
How to Repair the Cord on Vertical Blinds
- Step 1. Examine your vertical blind and find where the cord is broken. Make sure that you will be able to access the...
- Step 2. Take the scissors and snip off the ends of the cord where the cord is torn. You only need to snip off enough to...
- Step 3. Spread an old blanket under the area that you will be working. Doing so will...
How to fix a broken roller blind chain?
To ensure that the chain repair works properly, follow these steps:
- Take the blind down from the fixing brackets on the wall. ...
- Now, lay the blind out on a clean surface, and take the chain drive fixing from the end of the roller tube. ...
- Next, lay the chain out so that you can easily access both broken ends. ...
- Now, pull the chain through the chain drive to position the joining link. ...
How to fix broken Venetian blinds?
If the lifting and lowering cord has stopped working
- Remove your blinds from the window
- Remove the clamps securing the cords to the bottom slats
- Remove the old cord from the slats
- Thread the new lift cord over the pulleys in the top of the blinds and back down through the slats.
- Before tying the new cord off, ensure there is an even distance between the slats
How to fix damaged or broken audio cables?
Broken audio cables of all kinds can be fixed pretty easily and painlessly with a little time and a touch of solder. Small, cheap cables are expendable, but nicer cables – especially those attached to expensive equipment – aren’t as easy to just throw out. In general, thicker cables are easier to fix without a drop in quality and also ...
How to fix broken mobile charger cable?
10 old cables you should keep around (and 6 to toss)
- Sugru. Sugru is simply great to have on hand for a number of reasons -- one of those being old and worn out cables.
- A repurposed spring. A DIY solution that might work for a short while is removing the spring from a retractable pen, stretching it out and wrapping it around the cable ...
- Cable savers. ...
- It may be time for a replacement. ...

Can you fix broken blind cords?
Fixing or repairing a blinds string can be done easily. You can replace the string fully or only repair the broken string. What you'll need to repair blinds yourself are: new cord string, wire restring tool or blunt head large needle, flat head screwdriver, pliers, scissors, a tape measurer, and a lighter.
How do you fix the pull cord on a blind?
1:092:49How do I fix the pull cord on my Hunter Douglas blinds? - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then we're simply going to snap them together to hold that all in place. So those are back inMoreAnd then we're simply going to snap them together to hold that all in place. So those are back in make sure none of these little pieces popped out again um. And make sure this is all aligned.
How do you fix the cord in the shade?
0:101:01How to Replace a Cord Loop in an EZ Glide Honeycomb / Cellular ShadeYouTubeStart of suggested clipEnd of suggested clipWith the shade on a flat work surface gently pry the clutch cover. Off remove the cord by rotatingMoreWith the shade on a flat work surface gently pry the clutch cover. Off remove the cord by rotating the gear with the cord. Replace the court by rotating the gear with the cord in the opposite.
How do you fix a string to open and close a blind?
0:121:43How To Replace a Blind Tilt Mechanism | Fix Blinds That Won't ...YouTubeStart of suggested clipEnd of suggested clipAnd placing it on a smooth flat surface your blind might have end caps on each side of the headrail.MoreAnd placing it on a smooth flat surface your blind might have end caps on each side of the headrail. If it does remove them then slide the metal rail out just enough to clear the tilt mechanism.
How do I fix the cord on my Hunter Douglas blinds?
Step 1 – Remove the shade from the window, and lay it on a flat surface.Step 2 – Remove the clutch assembly from the headrail. ... Step 3 – Remove the cover from the clutch assembly. ... Step 4 – Remove the cord retainer clip. ... Step 5 – Remove and replace the cord loop. ... Step 6 – Replace the cord retainer clip and clutch cover.More items...
How do you replace the cord loop on Hunter Douglas blinds?
1:515:09EasyRise™ Cord Loop Replacement - Hunter Douglas - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy new cord loop through the end cap first here. Pulling the end cap cord through the end cap. Then.MoreMy new cord loop through the end cap first here. Pulling the end cap cord through the end cap. Then. I just want to walk my cord around and I'm pushing it on the clutch.
How do you Rethread Venetian blind cord?
2:386:22How to Re-Cord a Venetian Blind. - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust grab a hold of it with your pliers. And then push it down through the cord lock.MoreJust grab a hold of it with your pliers. And then push it down through the cord lock.
How do you fix drawstring on vertical blinds?
1:206:26How to Restring a Split Draw Vertical Blind Headrail - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou fuse the new string to the existing string by melting both ends pushing them together andMoreYou fuse the new string to the existing string by melting both ends pushing them together and rolling in between your fingers. Pull through to where it is knotted off at the other center carrier.
How do you Rethread Venetian blind cord?
2:386:22How to Re-Cord a Venetian Blind. - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust grab a hold of it with your pliers. And then push it down through the cord lock.MoreJust grab a hold of it with your pliers. And then push it down through the cord lock.
How do you fix the loop on a Hunter Douglas continuous cord?
2:215:09EasyRise™ Cord Loop Replacement - Hunter Douglas - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy new cord loop through the end cap first here. Pulling the end cap cord through the end cap. Then.MoreMy new cord loop through the end cap first here. Pulling the end cap cord through the end cap. Then. I just want to walk my cord around and I'm pushing it on the clutch.
How to order replacement cord for blinds?
Call Customer Service to order replacement cord. You will be asked for the workorder number of that particular blind. That number is inside of the headrail, if you don't have the original paperwork handy. Customer Service will reference this number to determine how much cord is needed.
Why do blind cords break?
Cords break for any number of reasons. Constant pulling up and down of a blind will produce friction. Friction causes heat. Heat causes weakness of some materials. Weakness in small objects cause breakage. Accidents happen. Dogs happen. You name it, it happens.
Can you pull cords out of headrails?
With the two ends joined, you can now pull on the corresponding cord that comes out of the headrail at the cord separator until you see the splice (tape or melt).
How to melt a cord?
Hold the end of the new cord in your hand. Light a lighter, and catch the end of the new cord on fire. Immediately blow out the flame. Attach the old cord and new cord together. This will melt the ends of the cords together.
How to bond cords?
Carefully, roll the hot, melted ends together between your fingertips to bond the cords together. Press gently so you don't burn yourself. When the ends are bonded after a minute or so , gently tug on the cord connection to ensure that the ends are bonded securely. If not, repeat the lighting procedure.
Can you replace a pull cord on venetian blinds?
Venetian blinds. Sometimes a pull cord for a blind gets stuck, needing repair--or breaks, requiring replacement. You can purchase replacement cords for your blinds from companies over the Internet or at your local hardware or building-supply store. Different-size blinds require specific cord widths; and since different styles ...
What to do if your vertical blind cord is broken?
Emery board. Paint that matches the color of your vertical blind’s cord. Repair your vertical blind's cord. If your vertical blind's cord is broken on an area that you can access easily, you can repair it yourself.
How to cut a cord that is torn?
Take the scissors and snip off the ends of the cord where the cord is torn. You only need to snip off enough to give the cord a clean cut with an even end.
How to get a cord out of a fire?
Hold one end of the cord in one hand. Make sure you are not holding too close to the end of the cord since you will be holding the cord over a fire. Strike the lighter with your other hand and carefully hold the lighter under the end of the cord only until it starts to melt. Do not let the cord catch on fire. If the cord catches on fire, immediately blow out the flame, snip off the end of the cord again, and start over.
How to burn a cord?
Hold one end of the cord in one hand. Make sure you are not holding too close to the end of the cord since you will be holding the cord over a fire. Strike the lighter with your other hand and carefully hold the lighter under the end of the cord only until it starts to melt. Do not let the cord catch on fire. If the cord catches on fire, immediately blow out the flame, snip off the end of the cord again, and start over.
How to stop vertical blinds from sticking?
Open and close the vertical blind slowly with the cord to make sure that it's working properly. Sand the cord again with the emery board if your vertical blind is sticking or stopping when opening or closing the blind.
2. Measure Your Blind Strings
Blind strings generally come in four different sizes, so you’ll need to measure or match the ones currently on your blinds to the new ones.
3. Cut Your Blind Strings to the Necessary Lengths
Cut one length of cord for each blind string you’ll be replacing. Have all of them ready to go so you can tackle the whole project at once.
4. Lower Your Old Blinds, Then Remove the Old String
Bring your blinds down to cover the window. Lift the bottom horizontal blind up and turn it over. A rail button or cap should be underneath, which you can remove with your fingers. Inside, you’ll find the knot holding your blind cords. Cut this knot.
5. Fuse the Old Strings to the New Strings
Note: You’ll need to use a lighter here, so be careful and make sure nothing flammable is nearby while you work.
6. Guide the New String Through the Blind, Then Tie It Off
Using the other end of the blind string, pull your new string through the blind until it reaches the proper length. Thread it through until your old cord has removed itself from the blind and been replaced by the new one. Then, cut the old blind cord.
7. Raise Your Blinds Carefully to Test Your Work
Now, the moment of truth: Gently pull on your blind cord to test them.
