
- Use a hand trowel to dig up the area above the sprinkler line. A shovel can break the sprinkler system even further.
- Cut a square patch with a shovel over the break if the line is buried. ...
- Remove the patch with 2–3 inches (5.1–7.6 cm) of dirt on the roots. ...
- Dig carefully around the sprinkler line to expose it. Once you’ve remove the patch of grass, you will be left with a clean square of earth above the break ...
- Clean off the section of exposed pipe with a wet cloth. ...
How much does repairing a sprinkler system cost?
The average cost to repair your sprinkler system is $75 to $250, with most homeowners paying $212. Most sprinkler repairs involve replacing sprinkler heads at $5 to $20 per head, or replacing valves at $20 to $40 per valve, not including the cost of labor of about $75 an hour by a professional plumber. Likewise, How deep are sprinkler lines buried?
How to repair a broken PVC sprinkler pipe?
Steps
- Ensure you have all the required supplies. Nothing is worse than having to run to the hardware store in the middle of a project.
- Find the rupture. Usually a soggy area of grass, but sometimes it is a geyser.
- Turn off the sprinklers, if you don’t this could be a very hard task.
- Dig up the pipe. ...
- Cut the pipe. ...
How to repair or replace a broken sprinkler head?
How to Replace a Sprinkler Head on an In-Ground Sprinkler System
- Shop for the right replacement sprinkler head. The first step in how to change a sprinkler head involves finding a replacement. ...
- Dig up the broken sprinkler head. After finding the right replacement, it’s time to start the sprinkler head repair. ...
- Unscrew the old sprinkler head. ...
- Attach the sprinkler head replacement. ...
- Test the new sprinkler head. ...
How do you replace a broken sprinkler head?
Steps to Fix and Replace a Broken Sprinkler Head
- Turn off the water system. Prior to starting the installation of the sprinkler head replacement, first, you have to ensure that you have shut off the water system properly.
- Dig a hole around the broken part. After you have shut off the water supply, it is time for you to dig up the issue. ...
- Dig down to the riser. ...
- Remove the old sprinkler head. ...

How do you splice a broken sprinkler wire?
2:004:36How to Make Waterproof Wire Splices for Irrigation Systems - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the stripped wires side by side and then twist on the wire connector with a clockwise motion.MorePlace the stripped wires side by side and then twist on the wire connector with a clockwise motion. This will draw the wires together and into the spring mechanism. Inside the body of the connector.
How do you fix a sprinkler cable?
1:464:47How to repair sprinkler or drip electrical line wire - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's different options the easiest. I found was using these Rainbird waterproof wire connectors.MoreThere's different options the easiest. I found was using these Rainbird waterproof wire connectors. So it came in a 10 pack about five six dollars for it. And it was actually cheaper than online.
Can you patch a punctured sprinkler line?
2:024:32Howto: fix a puncture in your sprinkler system - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically I just use this this tool here you can use whatever you can use a razor blade you cutMoreBut basically I just use this this tool here you can use whatever you can use a razor blade you cut it cut it right at the the crack.
How do you find a break in a sprinkler wire?
1:402:43Using a Pulser to Troubleshoot a Sprinkler System Wire BreakYouTubeStart of suggested clipEnd of suggested clipFrom the center point of the receiver. Move it back again. It's bouncing this direction now so IMoreFrom the center point of the receiver. Move it back again. It's bouncing this direction now so I know that the break is in between these two flags.
What kind of wire is used for sprinkler systems?
Most manufacturers include recommendations about what wire size to use with their valves, but typically, you can use 18-gauge wire if the length of the wire (not the distance) from the controller to the valve is less than 200 feet, and it's being installed as a residential system, says Sprinkler Warehouse.
What is a common wire in a sprinkler system?
Cut Common Wire The common wire is usually white in color and runs from your controller to your master cylinder and then to each of the other valves on your irrigation system in turn. If something happens to cut your common wire, then every valve after the cut will fail to turn on when activated.
How deep are sprinkler lines buried?
In most areas, burying the pipes 8 to 12 inches below the surface is adequate. This measurement is from the top of the pipe to the surface of the soil, which means your trenches must be slightly deeper to accommodate the pipes.
How do you cap a broken sprinkler pipe?
2:484:33How to Locate and Cap or Plug an Underground Sprinkler LineYouTubeStart of suggested clipEnd of suggested clipLooking good next slide the hose clamp on and insert the plug. There's not a lot of room in here butMoreLooking good next slide the hose clamp on and insert the plug. There's not a lot of room in here but i was eventually able to tap it in with a small hammer. Tighten the hose. Clamp.
What are goof plugs used for?
The goof plug is used to plug various-sized holes on drip tubing and drip line, or to close the end of 1/4″ micro tubing, 1/4″ soaker hose and 1/4″ drip line.
How do you run a sprinkler wire?
0:009:00How To Run Sprinkler Wire - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we do not have to worry about running conduit all the way back to the controller. We can just runMoreSo we do not have to worry about running conduit all the way back to the controller. We can just run the wire. In the ground in the same trenches as the pipe.
Can you run sprinkler wire above ground?
Running the wire above or under ground is not the issue. The most important concern is to make sure the wire won't get cut or damaged by any means. Burying the wire is recommended, since it is hidden and not subject to damage from garden shears, nylon string trimmers, vehicle tires, foot traffic, etc.
How do you repair a hole in a PVC sprinkler?
0:113:543 Ways to Repair PVC Irrigation Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip theMoreSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip the coupling over one section of the pipe. And then over the other tighten. The nuts.
How do you fix a hole in a plastic water pipe?
0:211:11PVC-pipe patch - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is your patch. Now you slather the glue inside of this and making sure that the factory edge isMoreThis is your patch. Now you slather the glue inside of this and making sure that the factory edge is the one that's going to engage the coupling here you spread glue here as well along this edge clip.
How do you fix a leaking sprinkler system?
2:567:26EASY Irrigation Sprinkler System Leak Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can put some kind of system in there to catch water turn on your irrigation. Line let it sprayMoreYou can put some kind of system in there to catch water turn on your irrigation. Line let it spray out any dirt or that may have gotten in the lines you want to check your fittings. For cracks.
How to find a leak in a sprinkler system?
After you turn on the sprinkler system, walk through the area where the sprinkler system is installed. Listen for running water and walk towards where you hear the sound to locate the leak in your sprinkler line .
How to tell if a sprinkler line is leaking?
Once you’ve identified where the leak is, mark the location so you can find it when the water is turned off.
Where is the break in the water line located?
The break or leak in the water line will be located between the last working sprinkler head and the first nonworking one.
How to stop water from leaking in a water line?
If you’ve found the signs of a leak and located the region where the line is leaking or broken, turn off the water so you can repair the line. Use the shut off valve in the control box to stop the flow of water through the system. Wait 1-2 minutes to allow the water to finish flowing through the system.
How to extend a plastic pipe?
Insert a slip coupling into the pipe. A slip coupling is a plastic pipe that is flexible and allows you to extend it to the length that you need it to be. Slide the end of the coupling into 1 end of the exposed pipe. Then, extend the coupling so it fits into the other end of the pipe.
What does a larger break in a system mean?
A larger break in the system could mean a costly repair.
Where to get a slip coupling for a pipe?
Bring the damaged section of pipe to the hardware store so you can get a slip coupling with a diameter that fits into it.
How to connect wires to valves?
Connect the wires to each valve using the masking tape notations as guides. Twist the wires together and cap them with twist-on wire connectors.
Where to turn on power to irrigation system?
Turn on the power to the irrigation system at the main electrical panel. Carefully test the control panel's connection to each valve.
How to match wires on a control valve?
Place a piece of masking tape on each exposed wire at each control valve. Note the wire color on the tape with a pen. Notating the wire color will help you match the new wiring after replacement. Each valve should have a colored wire and white ground wire connected to the main wiring line.
Where are the control wires on a water heater?
Locate the control wires exiting the control panel on your wall. Follow the wires until they enter the ground. The wires commonly flank the water pipe underneath the topsoil.
How to repair a tree line that has roots?
If the line was damaged by tree roots, reroute the line by digging a new trench away from the tree.
How to tighten a pipe clamp?
Place a clamp on one of the line ends, insert a slip coupling, then tighten the clamp. Place a clamp on the second pipe end, expand the coupling while inserting the nipple into the pipe, then tighten the clamp. Step 5.
How to fix a defective solenoid?
Disconnect the wires and unscrew the defective solenoid from the control valve. Insert a new one and turn it until it's finger-tight.
What happens if your watering system is not turning on?
Your watering system is divided into a series of zones. Generally, if you have a zone that's not turning on, you have an electrical problem. Make sure the zone wires are firmly attached to the terminals in the controller, the transformer is plugged in, and the circuit breaker at the main panel is on.
What is the phone number to access underground water lines?
Caution: Before you start digging to access the underground water lines, electrical wires or spray heads, dial 811 to have your underground utility lines identified and marked.
How to clean a syringe head?
Remove the screen basket from the bottom of the head, then clean it with water.
Which way to turn a valve?
Turn the valve on the horizontal pipe first, then the vertical pipe valve.
Can you replace a sprinkler valve solenoid coil?
1. The solenoid coil assembly of many sprinkler valves is replaceable. This allows repair to occur without having to remove/replace the plumbing part of the valve assembly. If you have a similar type spare valve unit you could also consider swapping the solenoid coil off of it to replace the one with the damaged wire.
Can you swap a solenoid coil off a valve?
If you have a similar type spare valve unit you could also consider swapping the solenoid coil off of it to replace the one with the damaged wire.
