How to Repair a Plastic Bumper Dent
- Inspect. Prior to undertaking any of the work necessary to repair the bumper dent, you should inspect it to determine the severity of the problem.
- Clean. Clean the area around the dent so any tools you might need to use can work properly. ...
- Use Heat for Small Dents. ...
- Rent Tools for Larger Damage. ...
- Repair Cracks or Holes. ...
- Touch Up Paint. ...
How much does it cost to fix a dented bumper?
Inusrance.com, in this car body repair article, said the average cost to repair a dented bumper could be as little as $450 for a repair to as much as $900+ for a replacement. Western Auto Body, a collision shop located in California, broke down the costs, including parts, paint and labor time.
How do you remove a dent in a plastic bumper?
The Two Fundamental Tools: Hot and Cold
- Method 1: Use Dry Ice. For a quick, inexpensive fix with minimal elbow grease, give dry ice a try. ...
- Method 2: The Boiled Water Method. As the name would suggest, this method entails using boiling water to remove the dent. ...
- Method 3: The Plunger Method. ...
- Method 4: Compressed Air and Heat. ...
How to repair a bumper Dent with a hair dryer?
Step 1: Equipment and Materials:
- kettle (boiling water)
- insulated rubber gloves (optional)
- hair dryer (extension cord long enough to reach your car)
- towel
- baseball bat (optional)
- various sized pieces of scrap lumber
- rubber mallet
- assistant (to hold hairdryer)
- nail polish (optional for scratches)
How to repair a bent or dented chrome bumper?
How to Repair a Bent or Dented Chrome Bumper
- Set the Emergency Brake. You need to make sure that the car will not move while you do the repairs, so it is best to set the ...
- Suck Out the Dent. In case the dent is small or you can’t reach behind it properly, it is better to suck out the dent using a ...
- Use Dry Ice. ...
- Banging Out the Dent. ...
- Repeat the Process. ...
Can you fix a dent in a bumper without replacing it?
By using the correct amount of heat and pressure, it is possible to reshape the bumper without causing more damage to it.
Can dents in plastic bumpers be repaired?
To fix a dent in a plastic bumper, you have to apply heat and then force the plastic back into its original shape. Here are a few strategies to remove a small dent from a car: Apply boiling water to the dented area. Reach under the wheel well and try to pop out the dent.
How do you get dents out of plastic bumpers?
Apply Heat to the Dent Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don't apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
How much does it cost to fix bumper dents?
If you just need to have the dent pulled back out and into place, the repair will likely cost $50-$100. However, if the dent is very deep and the paint was damaged as well, you could be looking at a repair of around $200-$1,000, depending on the dent and your chosen repair shop.
Do dent pullers work?
Do they work? Dent pullers only work on shallow dents that are positioned on a flat, flexible surface. They can improve the appearance of car dents but are unlikely to create a perfect finish. Unfortunately, DIY dent pullers will not work on deep, angular dents or damage along the edges of bodywork.
How do I get a dent out of my front bumper?
0:261:51How to fix a dent on the front or rear bumper cover on your ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying theMoreYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying the heat to the surface push out the dent using piece of wood.
Can hot water fix a dent in a bumper?
Yes, it can help remove dents from both metal and plastic bumpers. Fill a pot with water and bring it to a rolling boil. Carefully pour the water over the surface of the dent to heat up the metal. Allow the metal to flex and return to its original shape.
Does boiling water fix car dents?
Use boiling water Simply boil water in a teapot, protect yourself from burns with rubber gloves, and have a pot of cold water on hand. Then, pour the hot water from the teapot over the dent. Before it cools down, pop the dent out from the inside.
How do you pop out dents?
First, heat the dent with the hairdryer approximately six inches away for about 30 seconds. Then cover the dent with a piece of aluminum foil and rub dry ice over it. The rapid change from hot to cold should make the dent pop out within a minute or so. Another temperature trick involves boiling water.
Is it cheaper to repair or replace a bumper?
Bumper repair can be performed in-shop and is often cheaper than bumper replacement. Bumper repair normally costs between $100 and $1,000.
How long does it take to repair a bumper dent?
Standard dent repair can take anywhere from a couple days to 2 weeks. The biggest factor that contributes to the repair timeline is paint work – that is why paintless dent repair can happen so fast. Once the damage is repaired and the surface is perfectly smooth, the technician can begin painting.
How can I remove dents from my car at home?
0:413:15How to Remove Car Dents Fast - YouTubeYouTubeStart of suggested clipEnd of suggested clipSome water on your stove in a big pan. And pour it all over the dent area then put the suction cupMoreSome water on your stove in a big pan. And pour it all over the dent area then put the suction cup on it'll all batter. Plus the heat off and makes the metal. Get more flexible.
How to Pull a Dent From a Plastic Bumper Cover - Instructables
How to Pop a Dent Out of a Plastic Bumper - Car Care Portal
How to remove a dent from a front bumper?
Depending on the location of the dent on your bumper, you may need to remove the fender liner ahead of the front tire (see above) or a lower aerodynamic valance below the bumper to gain access to the interior of the dent. Both can be unclipped manually.
How to get a dent out of a car?
Use a rubber-tipped dowel or specialty tool (like the one shown in the illustration, readily available online) to push out the dent from the interior until it begins to pop back into its intended shape. You may need to gently work on any small indents with the tool to get a smooth surface. Then replace the fender liner.
How much does it cost to replace bumper covers?
Replacement bumper covers can cost more than $1,000. But dents in the soft plastic bumper covers on cars and SUVs can often be smoothed out at home by applying heat and a little elbow grease. It takes a bit of patience, and certainly experience helps. If you don't have a skilled friend to assist, be sure to watch a couple videos on YouTube for further insights on the techniques needed to get good results.
What happens if you damage a bumper?
Damage that affects the surface, like deep scratches or punctures, will require the services of a body shop. In such cases, the entire bumper cover may need to be replaced and painted, as well as other trim elements replaced and possibly lights moved.
How to make plastic bumpers malleable?
Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don’t apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
How to fix a dented bumper?
When you have access to the area behind the bumper and the dent is a minor one, you will find it can be fixed with the use of a heat gun or hair dryer. Heat guns can reach very high temperatures, so be sure you are wearing heat-resistant gloves, clothes, and eyewear when performing this repair. Direct the hot air from the hair dryer or heat gun at the dented section until it is just warm enough to become pliable. Then, simply reach around to push the dent out from the rear carefully. Leave the area to cool when it is finally back to normal.
How to fix dents in car rim?
For larger dents, a plunger tool will be required. The mouth of the plunger must be firmly attached to the surface to create an airtight seal, which can be improved by applying a little petroleum jelly to the rim. Once the plunger is correctly positioned, it should be held tightly and tugged backward to pull the dent out.
How to clean a dent in a car?
In either case, use a cloth to thoroughly dry the surface after it has been cleaned.
Can you use a bumper repair kit on plastic?
If you noticed any cracks during repair, or if you had to drill a hole to fix the dent, you can use a bumper repair kit to seal it. The kit should contain all the items that you need, but before you buy one, make sure you can use it on whichever type of plastic your bumper is made from.
Can a car accident cause a dent in a plastic bumper?
Anything from a car accident to just backing into a pole can leave a dent in your plastic bumper. An auto body shop can fix it, but why spend hundreds when you can easily do it yourself? By following the steps below, you can remove and repair unsightly dents in your plastic fender, and get your car looking as good as new again.
How to fix a dented bumper?
When you have access to the area behind the bumper and the dent is a minor one, you will find it can be fixed with the use of a heat gun or hair dryer. Heat guns can reach very high temperatures, so be sure you are wearing heat-resistant gloves, clothes, and eyewear when performing this repair. Direct the hot air from the hair dryer or heat gun at the dented section until it is just warm enough to become pliable. Then, simply reach around to push the dent out from the rear carefully. Leave the area to cool when it is finally back to normal.
Can you use a bumper repair kit on plastic?
If you noticed any cracks during repair, or if you had to drill a hole to fix the dent, you can use a bumper repair kit to seal it. The kit should contain all the items that you need, but before you buy one, make sure you can use it on whichever type of plastic your bumper is made from.
