Repair the holes where the towel rack holders were cemented by patching the drywall with drywall tape or fiberglass mesh and joint compound and sanding it smooth, advises Chris Skubisz. Paint the area to match the rest of the bathroom.
How to repair a loose towel rack?
To repair this problem:
- Loosen the set screws under the towel bar and remove it from the wall.
- Loosen the bracket screws and remove the brackets from the wall.
- Insert toggle bolts in each bracket.
- If needed, enlarge the bracket holes in the drywall with a screwdriver, and insert the toggle bolts in the holes.
- Tighten the toggle bolts so the brackets are secure.
How do you remove a towel rack from the wall?
To remove a ceramic fixture, such as a towel rack, from a drywall surface, you must:
- Cut through the plastic bar that spans between the two ceramic posts.
- Tape the wall around the base of each ceramic towel bar post.
- Use an oscillating multi-tool to cut through the adhesive between the wall and the towel bar holders.
- If absolutely necessary use a hammer along with a chisel or pry bar to pop the towel bar holders from the wall.
How to take a towel rack off the wall?
Removing A Towel Bar From The Wall
- Find the Screws. Depending on the towel bar that you own, there may be screws fastening it to the wall. ...
- Remove the Screws. Using a hex key or Phillips head screwdriver, you can now remove the screws from the towel bar. ...
- Remove the Wall Brackets. If your towel bar is attached to wall brackets, you will need to remove them. ...
- Patch the Holes. ...
How to attach a towel rack to recessed drywall?
- Using the set screw and wrench provided with your towel bar, attach one of the bar holders to the bracket.
- Slide the bar into place and attach the next bar holder.
- Put a little pressure on the towel bar to make sure it is secure.
- Hang towels.
How do you fix a ceramic towel rack?
0:131:35How To Install A Replacement Towel Bar - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide it into the holder. Push it side to side to little center itself. So with the bar in placeMoreSlide it into the holder. Push it side to side to little center itself. So with the bar in place that's it you just replace the bar.
How do you fix a drywall towel rack?
6:2412:07How to repair a TOWEL BAR Ripped out of the Drywall - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that's actually just raw drywall mud all through there. And all through there with nothing elseMoreSo that's actually just raw drywall mud all through there. And all through there with nothing else just raw drywall mud. Same with that one but this one impresses me because it's so huge.
How do you remove an old ceramic towel bar from a wall?
Place a pry bar between the holder and the wall over the masking tape. Push the top of the pry bar back to force the holder away from the wall. Follow the same process on all four sides until the ceramic towel rack holder releases.
Can you screw into patched drywall?
Plastic anchors, toggle bolts, and molly bolts allow you to reuse holes in drywall. Never drive a screw directly into drywall unless there is a stud behind the drywall at that point. Unanchored screws cannot support much weight and will pull out of drywall.
How do you fix a stripped screw hole in drywall?
1:124:06Fixing A Stripped Sheet Rock Screw Hole - YouTubeYouTubeStart of suggested clipEnd of suggested clipGoing around the sheetrock area there you will bond it all together and then when you go in you'llMoreGoing around the sheetrock area there you will bond it all together and then when you go in you'll make new threads with that with that toothpick there and with the glue.
How do you remove a ceramic toilet roll holder?
1:132:09DIY - How to Remove a Wall Installed Toilet Paper Dispenser - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you wanted to take a razor blade. And cut around the edges of this would be a good way to startMoreIf you wanted to take a razor blade. And cut around the edges of this would be a good way to start just. So that it's broken.
How do you reattach a ceramic toilet paper holder?
Construction Adhesive: Use masking tape to hold the fixture in place until the adhesive dries. Be sure to clean up and adhesive that got onto the outside of the fixture before it dries. After the adhesive dries remove the tape and place a small bead of latex caulk around the entire fixture and you are ready roll.
How do you fix a bathroom towel bar?
1:503:52Bathroom towel bar repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe next step is to take the towel bar bracket and the new spiral wall anchors come with the newMoreThe next step is to take the towel bar bracket and the new spiral wall anchors come with the new screw and I'll just thread them in through the bracket. Clockwise with the Philips. Screwdriver.
How do you fix a ripped drywall anchor?
3:148:05How To Fix A Pulled Out Or Damaged Drywall Anchor | Toggle BoltsYouTubeStart of suggested clipEnd of suggested clipYou can also from the back side take some needle nose pliers. And hold on to the plastic. Part andMoreYou can also from the back side take some needle nose pliers. And hold on to the plastic. Part and then use your phillips head and back that screw. Out.
How do you glue a towel bar to the wall?
Apply a small bead of Loctite® Power Grab® All Purpose Construction Adhesive to the back side of each end piece. Position the ends in place below the pencil marks and press firmly into place. For added assurance, place masking tape over each piece adhering it to the wall or tiles. Allow the glue to dry for 24 hours.
How do you fix a towel ring holder?
0:000:56How to Fix a Loose Towel Bar - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then all we have to do is just set it on the top. And we're going to use our precisionMoreAnd then all we have to do is just set it on the top. And we're going to use our precision screwdriver. And that's all there is to it to tighten up a taller.
How do you fix a drywall hook?
1:182:16Repairing a Towel Rack or Hook in Drywall - YouTubeYouTubeStart of suggested clipEnd of suggested clipDrill into the drywall until it hits. The tabs the cutter then just twists off screw in the plug.MoreDrill into the drywall until it hits. The tabs the cutter then just twists off screw in the plug. And stop when it's flush with the surface of the wall.
Step 2: Clean the Attachment Plate for Your Towel Rack
Our towel rack has a separate plate that attaches to the wall first, and then the arm that holds the towel rack is tightened onto the plate.
Step 3: Put Toggle Bolts on Attachment Plate
Toggle bolts come in two pieces - the bolt and the then toggle, which is a spring loaded v-shaped nut that helps provide traction on the other side of the wall. You'll want to insert the bolts through the attachment plate to prepare for the install.
Step 4: Insert Toggle Bolts Through Wall
Pinch all toggles closed and carefully insert them though the holes in the wall.
Step 5: Tighten Attachment Plate to Wall
To tighten the bolts and secure the attachment plate in place, you'll need to pull forward on on the plate, creating tension on the toggles.
Step 6: Attach Rest of Towel Rack and Enjoy!
Once the attachment plate is in place, you can install the rest of the towel rack and then hang your towels.
1. Measure For & Buy Your Replacement Supplies
Figuring out the supplies that I needed was the hardest part – once I had them, this was a 10 minute fix. You’ll need two things – a replacement bar and spring-loaded end caps. For the replacement bar, measure to see whether you need a 3/4″ or 5/8″ bar and also measure the length that you’ll need and buy a replacement bar that is as long or longer.
2. Remove the Old Towel Bar
Now that you’ve got your supplies, it’s time to go to work by removing the old towel bar. I easily pulled my bar out on its own since it was too short to begin with but if yours isn’t, you can remove it by sawing through the middle of it.
3. Cut Your New Replacement Bar to Size
When cutting your replacement towel bar to size, it’s important that you not cut it either too long or too short. Here’s what I did – I put a spring-loaded end cap into one end of my chrome bar and then put that end into one of the fixed wall brackets.
4. Put the Spring-Loaded End Caps on the Bar Ends & Install It!
After cutting my replacement bar to the correct size, I put the spring-loaded end caps onto both ends of the bar and installed it between the two fixed brackets.
