Chevrolet Silverado 1999-2006: How to Repair the Instrument Cluster
- Remove the gauge cluster trim. The upper-part of the dashboard is held in place via clips. Push the tilt lever for the steering wheel down.
- Remove the instrumental cluster. This part is easy, more so if you have a drill handy. ...
- Prepare the instrumental cluster board. The board is the chip set that powers all the gauges, lights and meters. First you have to gain access to it.
- Solder the points on the instrumental panel. First, you will need to remove the protectant clear finish on the contact points. ...
Is there a repair service for the instrument cluster on Chevy Venture?
If so, we offer a Malibu... This instrument cluster repair service is for 2001, 2002, 2003, 2004, and 2005 Chevrolet Venture. If your Chevrolet Venture instrument cluster is experiencing gauge issues or backlighting failure, then we can help!
What kind of instrument clusters do we repair?
We repair a wide variety of Chevrolet instrument clusters including Silverado, Suburban, Tahoe, Avalanche, Cavalier, Impala, Kodiak, Malibu, Monte Carlo, SSR, Tracker, Trailblazer, and Venture for many different issues. Click your make below to see the failures we service for specific models.
How much does it cost to repair a GM cluster?
Step 1: What We Repair? GM Gauge Repair If 1 gauge/needle is bad, they will all fail. These GM Clusters have 3 to 5+ issues with them. Our cluster rebuild covers ALL issues with our guarantee. $125.00 if you are in the following states: WI, MN, IA, IL, IN, OH and MI. $140.00 all other states.
How do I remove the instrument cluster?
After pulling off the trim bezel by hand (they have no screws on most models, they just pop off by pulling firmly.) you'll find a few 1/4" screws holding in the instrument cluster. Remove them and you will then be able to angle the instrument cluster out.
Can you repair a instrument cluster?
Sometimes it may be impossible to find an acceptable replacement instrument cluster for your vehicle. In that case, you can get it repaired.
How do you fix a car instrument cluster?
0:151:51Dorman's instrument cluster repair kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipBegin the installation by unhooking the trim panel from the - unscrew the two screws on each side ofMoreBegin the installation by unhooking the trim panel from the - unscrew the two screws on each side of the instrument. Cluster once unhooked unplug the connector harness in the back of the cluster.
What causes instrument cluster failure?
Overloaded Circuit A faulty voltage regulator, which sends power to the instrument panel in most current vehicles, may be responsible for what causes the instrument cluster to stop working.
What causes dashboard gauges to stop working?
When one gauge stops working, the problem may be in the gauge itself or a bad sensor, while all the gauges cutting out at the same time often indicates a blown fuse or a defective instrument cluster.
What are the common problems of the instrument cluster?
Some of the more common failures include:Erratic or non-functional gauges & inaccurate readings.LCD not Stuck or fluttering needles on gauges.Burned out indicator lights.Burned out/dark spot backlighting.Loss of LCD display or erratic operation (number 8 showing as 0)
How do I reset my GM instrument cluster?
Push and release the Sel/reset button button 3 times repeatedly. The instrument cluster begins its self-test. Each successive press of the Sel/reset button initiates a new cycling of all the gauges. To end, turn the ignition switch to OFF, or vehicle speed exceeds 1.5 mph.
Where is the fuse for the instrument cluster?
0:322:12INSTRUMENT CLUSTER FUSE LOCATION (2008 - 2016) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then leave the cover straight up on the back side of the cover you will also have a small fuseMoreAnd then leave the cover straight up on the back side of the cover you will also have a small fuse diagram. First fuse you want to check is the fuse.
Can you drive your car without the instrument cluster?
Can I drive my vehicle while the instrument cluster is out for repair? Yes, you can still start and run your vehicle without the instrument cluster.
Do you have to reprogram an instrument cluster?
In some newer vehicles, you may not need to do anything. The mileage will automatically show up on the new instrument cluster when you install it. It will receive the information from the computer or chip that contains it and display the mileage. In these cars, the instrument cluster is just a display.
How do I know if my gauge clusters are bad?
Indicators Of A Failing Instrument ClusterDim instrument cluster lights.The check engine light coming on sporadically or permanently. ... Intermittent failure of the gauges.Inaccurate gauge readings. ... Blinking lights.The lights glowing up or lighting up every now and then.More items...•
How do you test an instrument cluster?
0:000:53How to test a Ford Instrument Gauge Cluster - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you gotta do hold down the trip button when you turn the key on and that puts the cluster in aMoreAll you gotta do hold down the trip button when you turn the key on and that puts the cluster in a test mode.
How do you fix car gauges?
4:167:56How To Troubleshoot Faulty Gauges in your Classic Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe temperature sending unit is usually located in some sort of water passage. Inside the intakeMoreThe temperature sending unit is usually located in some sort of water passage. Inside the intake manifold or on the cylinder head and on this little 289. It's right here behind the distributor.
Can you drive your car without the instrument cluster?
Can I drive my vehicle while the instrument cluster is out for repair? Yes, you can still start and run your vehicle without the instrument cluster.
Can you just replace instrument cluster?
A broken or malfunctioning instrument or gauge cluster is not giving you the vital information you need about your vehicle. We're happy to tell you that you can replace your instrument cluster right at home. It's not as hard as it looks, and you'll save a lot of money in labor.
How hard is it to replace an instrument cluster?
Changing the instrument cluster is a relatively easy process and can be attempted by anyone who is familiar with a basic set of tools. There are a few things that can go wrong but the steps are still considered simple by most mechanics. Put aside roughly an hour to an hour and a half for this job.
Where is the fuse for the instrument cluster?
0:322:12INSTRUMENT CLUSTER FUSE LOCATION (2008 - 2016) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then leave the cover straight up on the back side of the cover you will also have a small fuseMoreAnd then leave the cover straight up on the back side of the cover you will also have a small fuse diagram. First fuse you want to check is the fuse.
How to remove a solder cluster?
First you have to gain access to it. Use your finger to separate the clips that hold the cluster together. Pull the backside cover of the cluster off. Figure 5. Removing backside cover. Place the board in a flat surface. Begin to heat up the solder torch. Inspect the solder points for the plug connector on the board.
How to get a truck out of the way?
With the key still turned to on, pull the gear selector down to one – use the emergency brake to keep the truck in place. Grab the dashboard panel and pull it towards you. Un-clip it and pull it out of the way.
Does the Silverado 1500 have an instrumental cluster?
The first-generation Cheverolet Silverado 1500 has an un fortunate tendency for their instrumental clusters to fail. Most drivers decide to replace their clusters without realizing there is an alternative, less expensive fix.
Can solder cracks be seen?
A good connection should not have any burn marks or cracks. When you visually inspect the solder you may be able to make out the damage areas, but it should still be noted that many cracks may not be so easily seen.
