how to repair concrete floors after removing tack strips

^{How to Repair Concrete Floors After Removing Tack Strips}

1. Wipe across the damaged concrete with a wire brush to remove cracked or chipped edges from the tack-strip nail holes.
2. Sweep the area with a broom or small brush to remove any loosened concrete, dirt or other debris.
3. Mix a quantity of epoxy concrete patch according to the manufacturer's directions.
4. Apply a dollop of epoxy concrete patch to each nail hole and smooth over with a putty knife.
5. Allow the epoxy concrete patch to cure for a minimum of 24 hours before applying any floor coating or treatment.

How do you remove tack strips from a concrete floor?

Clean concrete floors before patching the holes. Carpet tack strips are wooden boards installed around the perimeter of a floor to hold carpet in place. If you decide to remove the carpet, you must also pry up the tack strips, which are held in place with nails.

What happens if you remove carpet from concrete floor?

If you decide to remove the carpet, you must also pry up the tack strips, which are held in place with nails. If the floor is made of concrete, you are left with unsightly holes along the perimeter of the room. You can repair these holes by filling them in with a patching compound.

What should you do after prying up carpet tack strips?

The final step after you are done prying up all of the carpet tack strips is to clean up after yourself. While this sounds very basic, it is actually very important and should not be ignored. You will have to clean up the dust, tacks, wood, and any other debris. If you leave it, it could certainly interfere with the installation of a new floor.

What are tack strips for carpet?

Carpet tack strips are wooden boards installed around the perimeter of a floor to hold carpet in place. If you decide to remove the carpet, you must also pry up the tack strips, which are held in place with nails.

Do I need to repair concrete after removing tack strips?

Things You'll Need If you decide to remove the carpet, you must also pry up the tack strips, which are held in place with nails. If the floor is made of concrete, you are left with unsightly holes along the perimeter of the room. You can repair these holes by filling them in with a patching compound.

How do you fill nail holes in concrete floor?

You can fill small holes most easily using a premixed concrete patch, says Custom Building Products. Some products require you to add water, while others only need to be stirred; follow the manufacturer's instructions to determine how to use the compound you choose.

How do you remove carpet tack strips from a concrete slab?

0:002:02How To Remove Carpet Tack Strip From Concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight over where the nail is and then just hitting the end of the flat bar with a hammer and toMoreRight over where the nail is and then just hitting the end of the flat bar with a hammer and to jiggle the nail.

How do you remove tack strips without damaging concrete?

0:2612:53How to Remove Carpet Tack Strips From Concrete Floors - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll see these carpet tack strips are all out of order. And they basically look like this to be aMoreYou'll see these carpet tack strips are all out of order. And they basically look like this to be a nice little close-up shot here it's just a piece of strip of wood with these nails in it so you see

What do you use to patch concrete?

1:304:13How to Make Thin Repairs to Damaged Concrete with QUIKRETEYouTubeStart of suggested clipEnd of suggested clipUsing a margin trail mix the vinyl concrete patcher for three to five minutes. After a lump freeMoreUsing a margin trail mix the vinyl concrete patcher for three to five minutes. After a lump free consistency is achieved. Allow the mix to sit undisturbed.

How do you cover exposed carpet tacks?

0:5913:06DOORWAY TACK STRIP SOLUTION !!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr you can step on them with your bare feet and still fill those tacks come through a carpet unlessMoreOr you can step on them with your bare feet and still fill those tacks come through a carpet unless like I said it's a really thick.

How do you remove nails from a concrete floor without damaging it?

0:532:37Nails Be Gone - how to remove nail anchors from concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd leave the other part in the wall. Which is again in my case not really desirable scenario onceMoreAnd leave the other part in the wall. Which is again in my case not really desirable scenario once you hear this that means it's really moving in a concrete just needs a little bit of push.

How do you get rid of tack Steips?

2:053:48How To Remove Carpet Tack Strips | 2 Easy Methods! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the hole that's going through the tack strip is pretty small that nail in there so it'll just popMoreSo the hole that's going through the tack strip is pretty small that nail in there so it'll just pop right up now the second method is using a floor scraper.

How do you remove carpet grippers without damaging the floor?

2:055:32Carpet Removal (Gripper) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're trying to do this but the quickest way I found is to sort of delaminate. So I'm not touchingMoreWe're trying to do this but the quickest way I found is to sort of delaminate. So I'm not touching the parlor floor. Into the jail cells and getting underneath. If it lifts off the nail that's great.

How do you remove carpet gripper?

2:065:32Carpet Removal (Gripper) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're trying to do this but the quickest way I found is to sort of delaminate. So I'm not touchingMoreWe're trying to do this but the quickest way I found is to sort of delaminate. So I'm not touching the parlor floor. Into the jail cells and getting underneath. If it lifts off the nail that's great.

How do you remove nail subfloor from concrete?

0:001:01How to Remove Headless/Chipped Nails from Concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can get it at Lowe's or Home Depot and the hammer. What you want to do get your pry bar. JustMoreYou can get it at Lowe's or Home Depot and the hammer. What you want to do get your pry bar. Just put it right like this get a hammer and just tap it sharply. Like.

Step 1

Walk around the entire perimeter of the floor and identify any nails that are still in the floor. Grasp them with a pair of pliers, pull them out and dispose of them in the trash.

Step 2

Scrub each hole in the floor thoroughly using a wire brush to smooth out the top of each hole and to remove any loosened edges.

Step 3

Vacuum the entire room to remove all concrete dust and debris. While vacuuming, hold the hose over each of the holes for approximately two to three seconds to suck out any dust inside the hole. This dust must be removed so that the patch adheres properly.

Step 4

Open a tub of latex cement and mix the two components as directed by the manufacturer's instructions.

Step 5

Scoop up 2 to 3 tbsp. of the mixture using a trowel, and press it down into one of the holes in the concrete floor. Smooth the surface with the back of the trowel, and then turn the trowel sideways to scrape the excess off the surface of the floor.

Step 6

Repeat the process all the way around the perimeter of the concrete floor to repair the remaining holes.

Step 7

Allow the floor to dry overnight, until the material in the holes is completely hardened. Then put on safety glasses and a dust mask and insert a masonry wheel into a 4-inch grinder. Plug in the grinder, and use it to smooth down any rough surfaces over the holes.

How do you remove tack strips from concrete?

Pry up the nail. If it sticks in the concrete, hit the heel of the pry bar hard with the hammer. This should pop the nail free. Pull the tack strip up and back with your hands until the next nail stops you.

What is the best way to remove tack strips?

To easily remove the carpet tack strip, move the pry bar near a nail and pry up while gently lifting the end of the tack strip with your other hand. With this method, you’ll never break a strip unless the wood is rotten. Oh, and do be careful when removing carpet tack strips. Those tacks are beyond sharp!

How do you repair concrete after removing tack strips?

Wipe across the damaged concrete with a wire brush to remove cracked or chipped edges from the tack – strip nail holes.

Should you replace tack strips when replacing carpet?

Please leave the old tack strips in place. We should be able to reuse them. If there are any that are in bad shape we will pull them up and replace them when we arrive. You do, however, need to remove all the staples left over from the old padding.

Can you glue tack strips to concrete?

Diamond Member. You use concrete tack strips, same thing as regular but they have concrete nails instead.

What happens if you pull up tack strip?

As you continue to pull up the tack strip from the concrete, you will notice a trend. Some nails will break through the wood and remain in the concrete. If this happens, then you have a bit of extra work ahead of you.

What is a carpet tack strip?

Carpet tack strips are very durable parts of the carpet placement process. They are designed to hold your carpet in place over the concrete surface. For that reason, they are secured with very durable elements such as the nails that hold them. In some cases, they are secured to the floor with glue.

What is the first step in the construction process?

The first step that you will want to take in the process is to prepare. The best and most successful projects will have a large amount of preparation involved. Preparing for your project will ensure there are no unnecessary delays or safety issues that make the project more difficult.

Can you use a hammer to pound a pry bar?

Many find it helpful to pound the pry bar with a hammer to get it to fit. It’s very important that you get your pry bar well underneath the carpet tack strip. If you do have to use your hammer, try to avoid damaging the concrete floor. This could create extra work for you later on.

Is it hard to remove carpet tack strips?

That is why they are so difficult to remove. The good news is that removing carpet tack strips is not a complicated process. While they are meant to hold your carpet in place, they are not necessarily permanent.

Can you remove carpet tack strips from concrete?

Carpet tack strips are quite handy when holding carpet to slabs of concrete. However, removing them is far from convenient. It is not a complicated process, but it can be time-consuming. If you want to remove carpet tack strips from concrete without damaging concrete, you’re going to need some guidance. Carpet tack strips are generally secured ...