Service a Craftsman riding lawn mower to keep your mower in good operating condition. This includes changing the engine oil and filter; replacing the air filter and fuel filter; removing debris around the engine, transmission and mower deck; sharpening the blades; scraping the mower deck; and greasing riding mower.
Full Answer
How can I troubleshoot Craftsman lawn mower problems?
Troubleshooting a Sears Craftsman Riding Lawn Mower
- Does Not Start. Fill the fuel tank. ...
- Engine Does Not Turn Over. Press the clutch/brake pedal with your foot while starting the mower. ...
- Power Loss. Raise the cutting height or reduce your speed. ...
- Vibrations or Uneven Cutting. Turn the lawn mower on its side and clean the bottom of the deck to remove built-up leaves or grass.
- Grass Does Not Discharge Properly. ...
How to fix a lawn mower that won't start?
- Pull up the mower's hood to access the ignition switch.
- Remove its cable harness.
- Remove the tabs to pull the ignition switch out of its slot.
- Turn the key to the start position and set the multi-meter to measure resistance, not voltage.
- Connect the black multi-meter probe to the B prong and the other to the S prong. These terminals are along each other's diagonal at the bottom of the switch.
- Use the key to turn the ignition switch and start the engine. The resistance should display on the multi-meter when you do this.
How to repair Craftsman self propelled lawn mowers?
Some things that you have to check before working on your lanwmower:
- Safety gloves: Use safety gloves when you work with sharp or hot lawnmower parts. You also protect your hands from grease and oil spills.
- Use quality parts: Try to use quality parts. This can mean good OEM parts or genuine parts that the company recommends.
- Disconnect the battery: Disconnect the battery before working on your lawnmower. ...
How to fix a lawn mower with no compression?
- By reducing the cylinder diameter (to increase the compression ratio).
- By increasing the cylinder diameter (to decrease the compression ratio).
- By reducing the cylinder length/stroke length (to increase the compression ratio).
- By increasing the cylinder length/stroke length (to increase the compression ratio).
Why does my Craftsman mower won't start?
A Craftsman lawn mower won't start when the engine is not getting air, fuel or spark due to a plugged air filter, bad fuel, faulty switches, bad battery, bad spark plug, fuel blockages or dirty carburetor. Keep reading for my complete list of items that can prevent your Craftsman lawn mower from starting.
How do you fix a Craftsman riding lawn mower that won't start?
1:145:56Lawn Tractor Won't Start? Try This Easy Free Fix! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen just tilt the hood forward a bit lift it up now. Here's where the problem lies. This is theMoreThen just tilt the hood forward a bit lift it up now. Here's where the problem lies. This is the choke lever over here you can see it's loose.
How do you disassemble a Craftsman lawn mower?
2:177:06Craftsman Lawn Mower Disassembly – Lawn Mower Repair HelpYouTubeStart of suggested clipEnd of suggested clipUse a flathead screwdriver to help pry off both wheel. Covers. Now use a 9/16 inch socket to helpMoreUse a flathead screwdriver to help pry off both wheel. Covers. Now use a 9/16 inch socket to help loosen the mounting nuts securing the wheels unthread the nuts and you can remove both wheels.
Why does my lawn mower only run for a few seconds then dies?
If your lawn mower starts, runs briefly, then dies these are the four most common reasons that's happening: Dirty carburetor / clogged carburetor bowl. Old gasoline that has gone bad. Dirty or defective spark plugs.
When I turn the key on my lawn mower and nothing happens?
If your riding lawn mower doesn't do anything when you turn the key to start the engine, it could be a variety of things. This video shows you how to pinpoint the cause by checking the riding mower's battery, solenoid posts and coil, fuse, ignition switch, brake switch and blade switch.
What would cause a riding lawn mower to not start?
Your Mower Won't Start:Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten.Dirty Air Filter: Clean or replace.Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn't work, you might need a new fuel filter.
How do you service a Craftsman riding lawn mower?
1:444:14Lawn Mower Tune Up: Mower Tips From Sears Home ServicesYouTubeStart of suggested clipEnd of suggested clipYou can use a putty knife to remove any grass buildup while you're looking under the deck inspectMoreYou can use a putty knife to remove any grass buildup while you're looking under the deck inspect the condition of the blade if the blade is dull nicked or bent it should be replaced.
Who makes Craftsman mowers now?
All Craftsman mowers are made by MTD. Craftsman lawn tractors run the price spectrum from rear-drive models priced around $1,300 to fully featured, hydrostatic drive units that cost more than $2,000. Most Craftsman lawn tractors feature Briggs & Stratton engines, and the 42-inch-deck models are among the most popular.
How do you remove the engine cover on a Craftsman lawn mower?
0:131:04Briggs & Stratton Engine Cover Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere is only two screws holding it all but there's something can't see preventing it from comingMoreThere is only two screws holding it all but there's something can't see preventing it from coming off in order to remove the engine cover you're gonna have to do three things move the gas cap.
Why does my Craftsman lawn mower keep shutting off?
Your Craftsman Lawn Mower may start then die when your lawn mower is unable to regulate the air to fuel mixture required by the engine to form a combustion. This could be due to a dirty carburetor, bad fuel, plugged air filter, broken fuel pump, plugged fan or other components that can restrict fuel or air flow.
How do you fix a lawn mower that won't stay running?
0:166:26How To Fix Lawn Mower That Wont Stay Running! - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy back or look for tools or anything like that. So the kit that I use to rebuild the carburetor.MoreMy back or look for tools or anything like that. So the kit that I use to rebuild the carburetor. And air filter and all cost less than ten dollars off of Amazon.
How do you clean a carburetor on a Craftsman lawn mower?
1:269:52Cleaning Carburetor on Craftsman Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut it on here and just release it it shouldn't be too tight here pretty much uses this bolt and aMorePut it on here and just release it it shouldn't be too tight here pretty much uses this bolt and a rubber seal around the bowl to keep it sealed against the carburetor.
How do you clean a carburetor on a riding lawn mower?
4:398:15How to: Clean a Carburetor (Small engine) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith a little straw. And start blasting out this main jet and the fuel. Line. You don't need a tonMoreWith a little straw. And start blasting out this main jet and the fuel. Line. You don't need a ton just get all the gunk out.
How do you test a Craftsman ignition switch?
3:124:53How to test lawn mower key switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff the craftsman mower. So that's the concept on how to do it like I said go to your manuals theyMoreOff the craftsman mower. So that's the concept on how to do it like I said go to your manuals they have a section under the electrical. That usually will show a diagram.
How do I clean the carburetor on my lawn mower?
2:215:13How to Clean the Carburetor on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you want to make sure that's clean and the way you can do that is just simply get a piece ofMoreSo you want to make sure that's clean and the way you can do that is just simply get a piece of small wire. And see you and you poke it in and out of that hole make sure that it's clean.
How do you bypass a starter solenoid on a lawn mower?
How to bypass a solenoid starter on a lawnmower, step by stepStep 1: Turn the ignition switch on the “RUN” position.Step 2: Track down the lawnmower solenoid.Step 3: Find out the copper posts to be jumped.Step 4: Clean the carbon and rust deposits from the terminals.Step 5: Jump the solenoid.
What is Craftsman lawn mower?
Craftsman, as hinted by its name, offers its products to people who are professional mechanics to those who have the tenacity to do things themselves. They also have a series of self-propelled, electric, push, and reel lawn mowers that you can avail of. Ultimately, Craftsman offers a wide array of products that range from clothing, replacement blades, flashlights, and other utilitarian tools.
How does a transmission work on a lawn mower?
When the transmission is powered by the drive belt, the lawn mower wheels will engage and turn. To ensure that your transmission is properly working, check and observe it while the lawn mower is up and running. The lawn mower wheels should be turning while the transmission pulley spins. If not, this means that your transmission is damaged or defective. Replace it completely as the transmission cannot be repaired.
Why is my Craftsman mower not working?
If your Craftsman self-propelled lawn mower suddenly stops working, it might be because the traction control cable is misadjusted or broken. Check if the traction control cable moves freely to see if it’s working properly. If it doesn’t, lubricate it by putting a small amount of oil into the end of the cable.
What does a V belt do on a lawn mower?
The V-Belt is responsible for rotating the drive pulleys in order to drive the wheels of the lawn mower. if this part is broken or worn out, it means that your lawn mower wheels won’t be able to turn. To resolve this, check your V-belt first if there are damages. If there are, replace it completely.
What are the features of a self propelled lawn mower?
Some of which include grass-bagging, side-discharge, and safety features. There are also three-in-one models available that have mulching options as well.
What is hydro lock on a lawn mower?
Issue 2: Hydro-Lock. A hydro-lock can happen when the piston-cylinder is full of oil. This usually occurs when you tilt the lawn mower forward and hold it for a couple of minutes. In normal working conditions, the piston should move when you pull the starting rope.
How to remove a gear casing?
Using a flat screwdriver, you can put the casing off. Inside it, check first if there are any clogs in the gears. If there are, use a screwdriver to remove them. If the gears have any cracks, you will have to replace them. To do this, use a screwdriver again to remove the gears.
