
- Turn the ski or snowboard base-up and secure it in the vise to hold it in place. ...
- If you’re working on skis, be sure to lock the brakes up and out of the way. To do this, retract the ski brake by depressing the pedal. ...
- Check out the damage. If there are loose strands of base material around the hole, use your metal scraper to remove any extra base material around the gouge. ...
- Brush off any dirt or debris (brush from tip to tail).
- Clean the wound with a base cleaner to get rid of dirt and wax. Let the base cleaner dry completely.
- Use rubbing alcohol and a clean towel to remove residual base cleaner.
How do you fix a broken base on a snowboard?
Base Repair: Prepare the Base. Turn the ski or snowboard base-up and secure it in the vise to hold it in place. If you don’t have a vise, you can use a couple stacks of books to support your ski or board. If you’re working on skis, be sure to lock the brakes up and out of the way.
Can you fix damaged skis or boards?
Fixing serious edge damage by hand sometimes takes hours of work; it may be more cost effective to take your skis or board to a shop and let their stone grinder do the job. You’ll also want to make sure the base is flat and edge profile intact after working on them. Bent or missing sections of edge are pretty serious, but can often be fixed.
How do you fix moisture on skis?
Get the blade, chizzle, scraper or tool of your choice, underneath one end of the base weld and begin cutting anything that is higher than the base. Once you have removed the excess you may find very tiny air pockets. These are nothing to worry about, you can add more base weld if wanted, but your skis are now secure from moisture getting inside.
Can I repair a rock gouge in my ski base?
You're arcing perfect turns down the ski slope when you hear a loud scraping sound underfoot. Don't panic; repairing a rock gouge in your ski or snowboard base is relatively easy for a do-it-yourselfer. Here’s a step-by-step look at what to do.

Can you repair the bottom of skis?
Base Repair: Assessing the Damage If the gouge is shallow or mid-depth and does not touch the edge, you'll likely be able to repair it yourself. If the gouge is cavernous and touches the core or the edge, bring your skis or snowboard to a ski shop to be repaired.
How do you fix a ski base burn?
31:1934:50How To Renew A Sintered Base Ski and Fix Base Burn An ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipEven if it's just down each edge of the worked area of the ski. So. I've heard it said that you knowMoreEven if it's just down each edge of the worked area of the ski. So. I've heard it said that you know you can remove pace burn by applying a layer of hard wax and then coming back with the sharp.
How do you fix chipped skis?
0:001:00How to FIX & PROTECT your CHIPPED snowboard/ski, chipped ...YouTubeStart of suggested clipEnd of suggested clipBut the best option would be to go to an auto repair shop because they have books with colorMoreBut the best option would be to go to an auto repair shop because they have books with color swatches. And you can easily just find the right color match it will be in a spray.
How do you base weld skis?
Cut away any hanging or loose pieces of base material that will no longer serve any purpose.Take your lighter and begin heating the P-Tex stick. ... Core Shots. ... Now that the ski is clean you are going to need base weld or sometimes called metal bond. ... Begin pressing firmly down on the base weld using the metal scraper.More items...•
How do you repair a ski topsheet?
1:152:59How to - top sheet repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i tape these. Off. Then i'll just put a clamp. On. There let's try to get it right on that chip.MoreSo i tape these. Off. Then i'll just put a clamp. On. There let's try to get it right on that chip. And then i got one that i glued up over here last night i'll show you that one all dried.
How do you repair a PTEX ski base?
1:012:58How To Repair Your Ski And Snowboard Base With P-TexYouTubeStart of suggested clipEnd of suggested clipHold it low and close to the area. If. It is a deeper repair. It will need several layers of ptex toMoreHold it low and close to the area. If. It is a deeper repair. It will need several layers of ptex to filament. And let each new layer p-tech school in the base before relighting the stake.
How do you epoxy skis?
1:087:38How to repair a ski core shot when you still have plastic ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd see if we can get this to glue down and stay in place. So I got the Loctite marine epoxy whichMoreAnd see if we can get this to glue down and stay in place. So I got the Loctite marine epoxy which apparently works better on skis because it bonds to plastic. Be a little more flexible.
What is a ski base grind?
A grind is a pattern ground into the base of the ski with a stone grinding machine, and is performed by a ski service shop (that hopefully has a lot of experience and expertise doing this).
How long do skis last?
The average skier replaces their skis every 8 years but your skis peak performance diminishes after 100-125 full days of use – that's five years if you ski 20 days a year.
What is base weld material?
The material being welded, brazed, soldered, or cut.
What can I use instead of PTEX?
There is a product called JB Weld that works instead of P-tex and will sort of re-build your edge if your edge got pulled out. You will find it in a harware store for 5-6 bucks. It is more durable than P-tex and will weld better to your core, but it does not hold wax. clean up the wound, drown it in epoxy.
Can a core shot be fixed?
If you have a really deep core shot that goes into the fiberglass and has bits of broken glass or wood, you may need to glue them in place ahead of time, before P-texing, with a two-part epoxy adhesive.
Can a core shot be fixed?
If you have a really deep core shot that goes into the fiberglass and has bits of broken glass or wood, you may need to glue them in place ahead of time, before P-texing, with a two-part epoxy adhesive.
What is base burn on skis?
You'll also want to wax brand new skis and snowboards, even if they're waxed from the factory. Going too long in between wax jobs will damage your base, especially on dry snow. This is known as base burn, and it adds drag and compromises the ability of your base to absorb wax.
How much does it cost to repair a core shot?
A tune with a core shot that large would run folks between $60-$80. It's a lot of work. If you use p-tex, I recommend a base welder for the repair, which is a hot air gun that you use to melt p-tex. Many old-school ski shops have these.
What is base burn?
Chemical burns can be caused by acids or bases that come into contact with tissue. Acids are defined as proton donors (H+), and bases are defined as proton acceptors (OH-). Bases also are known as alkalis. Both acids and bases can be defined as caustics, which cause significant tissue damage on contact.
What is a core shot on a ski?
Core Shots. A core shot is when the core of the ski is exposed to the elements (water, moisture, snow etc..) instead of being protected. Moisture getting into the core of the ski is bad, that moisture can freeze too, so let's talk about how to fix it. Core shots are the most tricky and require the most work.
How to remove a P-Tex stick?
Take your lighter and begin heating the P-Tex stick. Hold the flame on the stick until it remains on fire. Rotating it while heating the P-Tex will speed up this process. Once you have a steady flame, start dripping the P-Tex into the gouge. Continue doing this until the P-Tex starts building up slightly higher than the base. Let the P-Tex cool for a few minutes and grab the tool you wish to scrape with -- A razor blade or a metal scraper seem to work the best. When you start removing the P-Tex, make sure to start from one end of the P-Tex you just melted and begin scraping over and over until you have made it flush with your base. Finish off with a few passes with the metal scraper and its almost as good as new.
Can you damage your ski base?
Whether its early, mid, or late season and it almost inevitable you will damage your ski or snowboard bases. A fresh piece of protruding ice on the east to a gnarly rock collision on the west, gouges and core shots are part of the sport. Bringing it to your local shop for repairs throughout the season can become costly, but fixing these problems can be done at home with the right tools.
Can you wax a ski?
So those pesky superficial scratches are driving you crazy. Don't let it, they are strictly visually disturbing and does not affect the performance of the ski. It may be difficult to ignore these hairline scrapes, but it is not worth filling. The best solution for this sort of damage is to give it a fresh hot wax. The wax will fill the scrapes and keep the skis gliding smooth without getting hung up or snagged on the snow.
How to repair scratches on ski board?
Many people burn sticks of P-Tex and fill the damaged area with dripping base material. This works, and fills the scratches evenly, but the high heat of the flame changes the character of the P-Tex and the repair will be softer than the rest of the base. If you use any color other than black, the soot may also be visible in the repaired area. For a cleaner, longer lasting repair, it’s best to use a commercial P-Tex gun (kind of like a hot glue gun that runs at a higher temperature and holds sticks of base material) or a base repair tool (basically a soldering iron with a flat tip). These tools also use specific P-Tex stock – either large round stock (for the gun) or small diameter “spaghetti” stock that will make your job easier.
How to repair a narrower core shot?
Narrower core shots are probably best repaired in the conventional manner after making sure the core is sealed, using either the base gun or base repair tool and razor blade or metal scraper.
How to repair a gouge in a car?
Make sure the damaged area is free of dirt and debris, and cut away any dangling bits of base before you start the repair. Work the new P-Tex in thoroughly and make sure it’s fully melted and fills the gouge completely. After the area is cool to the touch (around ½ hour), you can trim the excess off with a Surform tool (a handled scraping tool) or razor blade. Finish off with a sharp metal scraper to make the filled area totally level.
How to fix scratches on P-Tex?
Shallow, superficial scratches in your base (less than 1/2 mm in depth) are really hard to fill, since the P-Tex won’t stick well. You can min imize the depth of shallow scratches by removing the high spots with a sharp metal scraper or single edge razor blade (SERB). Hot wax over the area and you’ll hardly notice the damage. If you have several shallow scratches or are simply more picky about your gear, a stone grind from a qualified shop can often completely remove shallow base scratches and edge damage.
Can you wax ski clamps?
The patched area can be prepped and waxed as soon as the clamps are removed; you will probably need to do a bit of grinding and scraping to get the repaired area flush with the rest of the base. This is especially true on skis that have been tuned many times, where the ski base material is thinner than the P-Tex sheet used, and you may wish to bring it to a shop for a stone grind to get the repair totally smooth.
1. Clean the gouge
Carefully clean out any gouges with a knife or scraping instrument so that they are free from dirt and wax. Also cut off any loose slivers of base material as they will fall off in the future.
2. Light the candle
Hold your candle at one end and set alight the other. As soon the candle is lit, hold a metal scraper next to the flame, this should stop the flame turning orange. It is important to do this or the oxidisation of the candle produces carbon (little black bits) and this in turn weakens the material filling the gouge.
3. Let the P-Tex set
Let the P-Tex cool to form a solid bond in the gouge (approx 10 mins).
4. Scrape off the excess P-Tex
Take your metal scraper (holding at 45 degrees) and starting from the middle of the gouge (this helps to not rip out the new P-Tex) pull towards yourself till you reach the end of the gouge. Repeat this for the other half of the gouge
5. Look smug
Et voilà! You have filled and scraped your first gouge. Repeat this for all the gouges in your skis and you will be back up to top speed.
Recommended Tools
Base cleaner – Used to clean the wax out of the base in the area required.
Step 1: Clean the area
Start by inspecting the damage. If it’s a gouge then you’ll generally just need to cut off any overhangs and make the area flat using the razor blade. For a core shot, you’ll be looking to do the same thing but adding in the extra step of shaping the hole into an upside down wedge shape where possible.
Step 2: Melt the P-tex into the affected area
Using the lighter, set fire to your ptex stick. The trick with ptex is to keep the flame as blue as possible by holding the stick fairly upright and close to the damaged area.
Step 3: Scrape the excess P-tex
Time to be really careful and use the razor or whatever sharp scraping tool you have handy. As a general rule, always work in a tip to tail direction on skis to preserve the channels that help your skis glide efficiently.
Step 4: Wax
Finally, give your skis a good wax. They’ve earned the TLC from getting you down the mountain safely after running over some nasty debris.