- Inspect. Prior to undertaking any of the work necessary to repair the bumper dent, you should inspect it to determine the severity of the problem.
- Clean. Clean the area around the dent so any tools you might need to use can work properly. ...
- Use Heat for Small Dents. When you have access to the area behind the bumper and the dent is a minor one, you will find it can ...
- Rent Tools for Larger Damage. Tools specifically made to repair this kind of damage are available from car accessory supply stores or can often be rented when ...
- Repair Cracks or Holes. If you noticed any cracks during repair, or if you had to drill a hole to fix the dent, you can use a ...
- Touch Up Paint. Finish up by going over the whole repair with a proper primer and an automotive paint that matches your specific color.
How much does it cost to fix a dented bumper?
Inusrance.com, in this car body repair article, said the average cost to repair a dented bumper could be as little as $450 for a repair to as much as $900+ for a replacement. Western Auto Body, a collision shop located in California, broke down the costs, including parts, paint and labor time.
How do you remove a dent in a plastic bumper?
The Two Fundamental Tools: Hot and Cold
- Method 1: Use Dry Ice. For a quick, inexpensive fix with minimal elbow grease, give dry ice a try. ...
- Method 2: The Boiled Water Method. As the name would suggest, this method entails using boiling water to remove the dent. ...
- Method 3: The Plunger Method. ...
- Method 4: Compressed Air and Heat. ...
How to repair a bumper Dent with a hair dryer?
Step 1: Equipment and Materials:
- kettle (boiling water)
- insulated rubber gloves (optional)
- hair dryer (extension cord long enough to reach your car)
- towel
- baseball bat (optional)
- various sized pieces of scrap lumber
- rubber mallet
- assistant (to hold hairdryer)
- nail polish (optional for scratches)
How to repair a bent or dented chrome bumper?
How to Repair a Bent or Dented Chrome Bumper
- Set the Emergency Brake. You need to make sure that the car will not move while you do the repairs, so it is best to set the ...
- Suck Out the Dent. In case the dent is small or you can’t reach behind it properly, it is better to suck out the dent using a ...
- Use Dry Ice. ...
- Banging Out the Dent. ...
- Repeat the Process. ...
Can you fix a dent in a bumper without replacing it?
By using the correct amount of heat and pressure, it is possible to reshape the bumper without causing more damage to it.
Can a plastic bumper dent be repaired?
While these damaged plastic car bumpers can be repaired, for most of them, they shouldn't be repaired. And there is one main reason why. It is more expensive. Most often, replacing a damaged plastic front bumper is actually going to cost less than getting it repaired.
How do you get dents out of plastic bumpers?
Apply Heat to the Dent Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don't apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
Can you push out a dent in a bumper?
To remove a dent from your bumper, you need to make it more malleable. This can be accomplished by dousing the dent with hot water. Heat water to boiling in a pot or big tea kettle and pour it over the dent. Wearing gloves to protect your hands, quickly reach behind the bumper and push out the dent.
How much does it cost to fix a dent in a bumper?
If you just need to have the dent pulled back out and into place, the repair will likely cost $50-$100. However, if the dent is very deep and the paint was damaged as well, you could be looking at a repair of around $200-$1,000, depending on the dent and your chosen repair shop.
How do I get a dent out of my front bumper?
0:261:51How to fix a dent on the front or rear bumper cover on your ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying theMoreYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying the heat to the surface push out the dent using piece of wood.
Can hot water fix a dent in a bumper?
Yes, it can help remove dents from both metal and plastic bumpers. Fill a pot with water and bring it to a rolling boil. Carefully pour the water over the surface of the dent to heat up the metal. Allow the metal to flex and return to its original shape.
Do suction cup dent pullers work?
They can improve the appearance of dents but probably won't create a perfect finish. But these tools will not work on deep, angular dents or damage along the edges of bodywork. Dents in areas of thick metal will also be very difficult to remove at home.
How do you pop out dents?
First, heat the dent with the hairdryer approximately six inches away for about 30 seconds. Then cover the dent with a piece of aluminum foil and rub dry ice over it. The rapid change from hot to cold should make the dent pop out within a minute or so. Another temperature trick involves boiling water.
Can you fix a dent in a metal bumper?
0:251:49How to Remove Metal Bumper Dents - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you had a softer metal where you don't want a lot of this to raise up you can use this there's aMoreIf you had a softer metal where you don't want a lot of this to raise up you can use this there's a bunch of others in there and you just tap from the backside.
How to remove a dent from a front bumper?
Depending on the location of the dent on your bumper, you may need to remove the fender liner ahead of the front tire (see above) or a lower aerodynamic valance below the bumper to gain access to the interior of the dent. Both can be unclipped manually.
How to get a dent out of a car?
Use a rubber-tipped dowel or specialty tool (like the one shown in the illustration, readily available online) to push out the dent from the interior until it begins to pop back into its intended shape. You may need to gently work on any small indents with the tool to get a smooth surface. Then replace the fender liner.
How much does it cost to replace bumper covers?
Replacement bumper covers can cost more than $1,000. But dents in the soft plastic bumper covers on cars and SUVs can often be smoothed out at home by applying heat and a little elbow grease. It takes a bit of patience, and certainly experience helps. If you don't have a skilled friend to assist, be sure to watch a couple videos on YouTube for further insights on the techniques needed to get good results.
What happens if you damage a bumper?
Damage that affects the surface, like deep scratches or punctures, will require the services of a body shop. In such cases, the entire bumper cover may need to be replaced and painted, as well as other trim elements replaced and possibly lights moved.
How to make plastic bumpers malleable?
Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don’t apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
How to fix a dented bumper?
When you have access to the area behind the bumper and the dent is a minor one, you will find it can be fixed with the use of a heat gun or hair dryer. Heat guns can reach very high temperatures, so be sure you are wearing heat-resistant gloves, clothes, and eyewear when performing this repair. Direct the hot air from the hair dryer or heat gun at the dented section until it is just warm enough to become pliable. Then, simply reach around to push the dent out from the rear carefully. Leave the area to cool when it is finally back to normal.
How to fix dents in car rim?
For larger dents, a plunger tool will be required. The mouth of the plunger must be firmly attached to the surface to create an airtight seal, which can be improved by applying a little petroleum jelly to the rim. Once the plunger is correctly positioned, it should be held tightly and tugged backward to pull the dent out.
How to clean a dent in a car?
In either case, use a cloth to thoroughly dry the surface after it has been cleaned.
Can you use a bumper repair kit on plastic?
If you noticed any cracks during repair, or if you had to drill a hole to fix the dent, you can use a bumper repair kit to seal it. The kit should contain all the items that you need, but before you buy one, make sure you can use it on whichever type of plastic your bumper is made from.
Can a car accident cause a dent in a plastic bumper?
Anything from a car accident to just backing into a pole can leave a dent in your plastic bumper. An auto body shop can fix it, but why spend hundreds when you can easily do it yourself? By following the steps below, you can remove and repair unsightly dents in your plastic fender, and get your car looking as good as new again.
Can you fix a dent in a chrome bumper?
Dents in a metal or chrome bumper can be unsightly and tempting to fix, and there is a simple method for fixing them. While you may not be able to repair a chrome or metal bumper to a completely smooth condition or appearance, it is possible to fix dents enough so they are hardly noticeable. If you have a dent in your bumper and would like to remove it, this guide explains how to get a dent out of a metal bumper with a hammer and dolly.
Will the Dent Smoothen Out Perfectly?
It’s probably not possible to repair the dent to the original condition, but it should smoothen out.
