How to Repair a Plastic Bumper Dent
- Inspect. Prior to undertaking any of the work necessary to repair the bumper dent, you should inspect it to determine the severity of the problem.
- Clean. Clean the area around the dent so any tools you might need to use can work properly. ...
- Use Heat for Small Dents. ...
- Rent Tools for Larger Damage. ...
- Repair Cracks or Holes. ...
- Touch Up Paint. ...
Full Answer
How do you remove a dent from a plastic bumper?
Things You'll Need
- Gloves
- A Phillips or flat head screw driver
- Long nose pliers
- Wrench
- Extension
- Socket
- Heating blower
- Object/stick
How to repair a dent in your plastic bumper.?
The Two Fundamental Tools: Hot and Cold
- Method 1: Use Dry Ice. For a quick, inexpensive fix with minimal elbow grease, give dry ice a try. ...
- Method 2: The Boiled Water Method. As the name would suggest, this method entails using boiling water to remove the dent. ...
- Method 3: The Plunger Method. ...
- Method 4: Compressed Air and Heat. ...
How much does it cost to repair a plastic bumper?
When these are summed up, it will merely show why it involves so much to fix a plastic bumper. Labor – It costs about $200-$300 at $100 per hour with a duration of about 2 – 3 hours. Painting – It costs about $300-$400 at $100 per hour with a duration of about 3 – 4 hours.
How do you fix a bumper Dent?
- Scrub the bumper with dish soap and water using a dish scrubbing pad.
- Sand the entire rubber bumper with 80-grit sandpaper to remove all of the paint.
- Wave a heat gun across the back and front of the bumper wherever there is a dent or blemish.
Can dented plastic bumpers be repaired?
To fix a dent in a plastic bumper, you have to apply heat and then force the plastic back into its original shape. Here are a few strategies to remove a small dent from a car: Apply boiling water to the dented area. Reach under the wheel well and try to pop out the dent.
Can a bent plastic bumper be repaired?
It depends on how seriously the bumper is misshapen. If you want to try a homemade fix: Apply boiling water to the bumper and then reach inside the wheel well to pop it back. Apply a heat gun or blow dryer to the area for three minutes and then pop the plastic back.
How do you fix an indent on a bumper?
0:261:51How to fix a dent on the front or rear bumper cover on your ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying theMoreYou can also achieve the same effect by using heat gun or hair dryer. Immediately after applying the heat to the surface push out the dent using piece of wood.
Can you fix a dent in a bumper without replacing it?
By using the correct amount of heat and pressure, it is possible to reshape the bumper without causing more damage to it.
How do you reshape a plastic bumper?
1:1616:22DIY Bumper Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipBag. Then take some cold. Water. And hold it on the bumper. And this is going to ensure that it doesMoreBag. Then take some cold. Water. And hold it on the bumper. And this is going to ensure that it does not warp. Back into its original. Shape.
Is it cheaper to repair or replace a bumper?
Bumper repair can be performed in-shop and is often cheaper than bumper replacement. Bumper repair normally costs between $100 and $1,000.
Can a body shop fix a bent bumper?
Damages that Require Replacement However, if all the connectors on your bumper are in place and intact, then your auto body shop may be able to fix the alignment or reattach it. This requires the bumper to still be in otherwise good condition.
How much does it cost to fix a dent in a bumper?
If you just need to have the dent pulled back out and into place, the repair will likely cost $50-$100. However, if the dent is very deep and the paint was damaged as well, you could be looking at a repair of around $200-$1,000, depending on the dent and your chosen repair shop.
Does boiling water remove dents in cars?
Use boiling water It can also be used to potentially remove unwanted depressions in your vehicle, that is, as long as you have a plastic bumper and are successfully able to access the dent from the backside.
Can you drive around with a dented bumper?
Damaged bumpers Bumpers may become cracked or loose during collisions. If your bumper appears to be ready to fall off or has sustained damage that may hurt pedestrians or others on the road, it may be safer to have the bumper repaired before getting back on the road.
How do you bend a bumper back in place?
1:064:44Easy Bumper Straightening - Hustler Stick Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you sight down it and then you twist it and align it well that gets it straight but the problemMoreAnd you sight down it and then you twist it and align it well that gets it straight but the problem is if your bumper brackets themselves are a little tweaked. This is the stick.
How do you weld a plastic bumper?
3:356:56Bumper Repair with Hot Air Plastic Welder - YouTubeYouTubeStart of suggested clipEnd of suggested clipHeat the tip of the rod and the base material with the welder until the rod melts together with theMoreHeat the tip of the rod and the base material with the welder until the rod melts together with the base material. Apply downward pressure on the rod as it is melting the downward.
Money-saving steps to repair this common problem
When you shop through retailer links on our site, we may earn affiliate commissions. 100% of the fees we collect are used to support our nonprofit mission. Learn more.
Get Access Behind the Bumper
Depending on the location of the dent on your bumper, you may need to remove the fender liner ahead of the front tire (see above) or a lower aerodynamic valance below the bumper to gain access to the interior of the dent. Both can be unclipped manually.
Apply Heat to the Dent
Warm the bumper surface with a heat-gun tool if you have one (hot water or a powerful hair dryer will work, too) to make the plastic more malleable. Don’t apply strong heat too closely or hold the heat source in the same spot for too long—either can damage the paint.
Gently Push Out the Dent
Use a rubber-tipped dowel or specialty tool (like the one shown in the illustration, readily available online) to push out the dent from the interior until it begins to pop back into its intended shape. You may need to gently work on any small indents with the tool to get a smooth surface. Then replace the fender liner.
