
How to repair drywall dents and tiny holes:
- Fill dents and tiny holes with lightweight spackle using your finger or a putty knife.
- Make sure the spackle completely fills the dent or hole and is level with the rest of the undamaged wall.
- Allow the spackle to dry for 15 to 30 minutes or the time recommended by the manufacturer.
- Once dry, use a fine-grit sandpaper to sand the area smooth.
- Brush away any debris and touch up the paint.
What tools are needed to fix a hole in drywall?
Other Tools That Are Nice to Have:
- Keyhole Saw
- Drywall Screw Gun
- Cordless Drill
- Drywall T square
- Rasp
- RotoZip ®
- Ten Inch Drywall Knife
- Halogen Light
- Sanding Pole
How to fix a large hole in your drywall?
Method 2 Method 2 of 2: Patching with a New Piece of Drywall Download Article
- Cut the hole into a neat square or rectangle. Home Improvement Specialist Expert Interview. ...
- Create a patch out of drywall that is 2 in (5.1 cm) taller than the hole. ...
- Put a screw through the middle of the patch to make a handle. ...
- Apply construction adhesive to the bottom and top edges of the patch. ...
How do you fix a hole in drywall?
How to Repair Cracks and Holes in Drywall
- Surface Crack Repair. Unlike plaster, drywall has a seamless paper covering that rarely cracks or splits. ...
- Deep Crack Repair. If the crack extends through the seam’s paper tape or if the tape has pulled loose from the wall, use a razor knife to cut the tape ...
- Nail Pop Repair. ...
- Corner Bead Repair. ...
- Small Hole Repair. ...
- Large Section Repairs. ...
How to patch screw holes in drywall easily?
Patching small Drywall holes:
- Start by removing the nail or screw from the wall (and be sure to remove the anchor as well if there is one).
- Use the cap of the 4-in-1 Patch Plus Primer to (very) lightly sand down the wall to remove any paint or drywall flakes.
- Squeeze a bit of the Patch Plus Primer into the hole – you want it to completely fill the hole and overflow just a little.

Can you repair drywall holes?
2:4915:38How to Fix Holes in Drywall - 4 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimilar with the first one you can buy a large patch that's a mesh adhesive patch like this one hereMoreSimilar with the first one you can buy a large patch that's a mesh adhesive patch like this one here we can actually just apply this eight by eight patch over the whole thing.
How do you repair a large drywall hole?
Fix Large HolesStep 1: Cut Out a Piece of Drywall to Use as the Patch. ... Step 2: Trace the Patch Size Over the Hole. ... Step 3: Cut Out the Hole. ... Step 4: Attach Furring Strips Inside the Hole. ... Step 5: Attach the Patch to Furring Strips. ... Step 6: Apply Joint Tape to the Patch. ... Step 7: Apply Joint Compound.
How do you fix a drywall hole for beginners?
0:318:18How To Patch a Hole in Drywall (For Beginners) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou need some mesh tape to start finishing that surface of the drywall. And then you're gonna needMoreYou need some mesh tape to start finishing that surface of the drywall. And then you're gonna need some compound to fill the cracks. And the holes and the mesh tape.
What repairs drywall holes?
0:033:09How to Repair Drywall - YouTubeYouTubeStart of suggested clipEnd of suggested clipGot a few holes in your walls fix your damaged drywall with these simple repair tips small dings andMoreGot a few holes in your walls fix your damaged drywall with these simple repair tips small dings and dents are easy scrape away loose debris apply lightweight spackle.
What is the fastest way to fix a hole in the wall?
0:211:48How To Fix a Hole in the Wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipThese plaster patches are super easy to attach. You simply peel off the back and stick it onto theMoreThese plaster patches are super easy to attach. You simply peel off the back and stick it onto the wall. Just smooth down the edges even grab your spatula to make sure it's really smooth.
How big is too big for spackle?
Use spackle to repair holes less than 4 inches (10 cm) in diameter. Spackle can be used to repair holes up to the size of your hand. You will have to use a support like mesh or wire to repair holes larger than 4 inches (10 cm) in diameter.
What kind of putty is used for drywall?
Joint compound, also called drywall compound, is a putty that has the consistency of plaster and is designed for larger jobs. Joint compound is made by mixing gypsum dust and water into a paste. It's usually comes in a pre-mixed container for your convenience and is commonly used for taping and finishing drywall seams.
How do you spackle drywall holes?
0:453:04How to fill and spackle holes in drywall. Fixing a hole in sheet rock ...YouTubeStart of suggested clipEnd of suggested clipInto your exterior spackle. And press it in so it fills up that hole. Take our whines back and.MoreInto your exterior spackle. And press it in so it fills up that hole. Take our whines back and. Right. Once that holds level in smooth.
How do I fill a hole in the wall?
Mix filler with a small amount of clean water and stir to a smooth, creamy consistency. Dip 2 inches of the edge of the filling knife into the spackling paste and apply a thin layer on the wall in one horizontal stroke. Press firmly to ensure that the mud fills the screw hole. PRO TIP: The coats shrink as they dry.
Small Dents and Dings
Scrape away loose debris from the hole. Cover the hole or dent with fast-drying spackle to bring the spackle level with the drywall surface and let it dry 24 hours -- or the time recommended by the manufacturer’s instructions. Sand smooth.
Popped Nail Heads
A popped nail isn't holding in the stud and backs out of the drywall, creating a popped nail head.
Small Holes
For small holes, like those created by a doorknob, a patch kit may be used.
Large Holes
For holes larger than 6 inches, you'll create a drywall patch with a different attachment method for the repair.
Corner Bead Patch
Corner bead is used where two pieces of drywall meet to form a corner. Corner bead is available in a variety of materials, including metal, paper and vinyl.
Finish the Repair
You're almost done. Here's where you make it look like nothing happened.
Repair Textured Drywall
Textured drywall is a bit more complicated, but still pretty simple to repair.
Why do drywall screws pop up?
But drywall screws sometimes pop up too, as a result of damp framing that dries out and shrinks during the first year or two in new construction. The first step of how to patch a small hole in the wall is to drive nails back down using a nail set.
How to get a hump out of tape?
Squeeze some, but not all, of the compound out from under the tape so you don’t create a big hump on the wall. Immediately apply a light coating to the topside of the tape, tapering it out onto the wall.
Tips
If you have a hole that is too large to repair with spackle, repair it with a square piece of drywall tape. Use joint compound to stick it to the wall. Cover it with a layer of joint compound and sand when dry. [37]
About This Article
This article was co-authored by Allen Lee. Allen Lee is a Home Improvement Specialist and the Owner of Honest Lee Handyman Services, a licensed and insured handyman business servicing Sacramento, California, and surrounding areas.
Need more help? Talk to a drywall repair expert
Our partners can help you compare quotes from top-rated professionals near you
Prepare the Opening
Trim the edges of the hole to create straight sides and a square or rectangular overall shape. Use a framing square and a pencil to mark cutting lines on the drywall. Then cut along the lines with a drywall saw.
Warning
Make sure there is no wiring or plumbing behind the drywall surface before cutting by looking through the hole with a flashlight.
Install the Backing Strips
Cut two pieces of lumber or plywood a few inches longer than the long sides of the hole (if it's a rectangle). Place one piece into the hole, parallel to one of the long sides, so the strip is centered over the drywall edge (half is behind the drywall and half is exposed).
Install the Drywall Patch
Cut a piece of drywall to fit the hole. It doesn't have to be a snug fit, but the seams should be not more than about 1/8 inch wide. Position the patch over the hole and secure it to the backing strips with screws. Keep the screws about 1 inch from the edges of the patch and space them 6 inches apart.
Tape the Seams
Cut strips to length of drywall joint tape using a utility knife. Cover each seam with a strip of joint tape. Overlap the tape strips at the corners. Make sure the tape lies flat, with no wrinkles or bulges.
Mud the Seams
Cover the drywall tape with a thin layer of drywall joint compound, using a 6-inch drywall knife. You should be able to see the mesh through the compound. Let the compound dry. Then scrape the surface with the knife to remove any burrs or clumps.
How to repair a sanded area?
If you cut corners on sanding, the repair site will be noticeable, so take your time. Once the repaired area is dry, use a fine-grit (100 or 120) sandpaper. After the first round of sanding, add a second layer of mud, spreading it about 2 inches beyond the boundaries of the first layer. Once dry, re-sand.
Is joint compound easier to sand?
DO keep it light. Less is generally more when it comes to joint compound. A thin coat is easier to sand, and you’ll be less likely to remove too much while sanding and expose the patch. Also, for joint compound to appear flush with the wall near the damage site, “feather” the mud as you apply it.
Is drywall indestructible?
Drywall is tough, but it’s not indestructible. Over time, gypsum-board walls can sustain ugly cracks or holes. Fortunately, drywall is fairly easy to repair, but there is an art to it. Here’s what to do—and what to avoid—when fixing drywall damage so it’s indiscernible to landlords, homebuyers, or visitors.
Do you need a mask when sanding drywall?
DO use protection. The fine particulate of drywall compound could injure your lungs if inhaled. So always wear a dust mask when sanding drywall compound. Disposable gloves are also a good idea to protect your hands from the dehydrating effects of gypsum dust.
