How to Repair Eaves & Roofs
- Using your hand drill, remove your gutters by unscrewing them from their support braces. Brace the gutter by having someone else hold the freed ends.
- Measure the height and length of the damaged eaves.
- Purchase replacement eaves at your local hardware store or lumberyard. ...
- Using a pry bar, pull the old eaves off.
Full Answer
How to repair rotted eaves on roof?
How to Repair Rotted Eaves. 1 Step 1 – Inspect Your Damage. While you are preparing for your repairs, do a thorough check. Run a hose on your roof. If the water streams into the ... 2 Step 2 – Remove the Shingle Mold. 3 Step 3 – Take off the Rotted Fascia. 4 Step 4 – Remove Soffit. 5 Step 5 – Take off Rotted Rafter. More items
Should I repair or replace my eaves?
Unless your home has been severely neglected, the need to replace the entirety of the eaves 1 is unlikely. In most cases, repairing the components of the eaves 1 requires replacement of specific sections of soffit 3, fascia, gutter, or rafter tails. Enhancement and Improvement Costs
How do you fix a leaking eaves on a house?
Start by prying away the bottom and sides of the old eaves and cutting new materials to match. Apply a resilient weatherproof coating to the new pieces, then secure them using stainless steel nails. Finish by sealing up cracks and crevices with caulk to keep water, squirrels, insects, and other destructive intruders out for good.
How much does it cost to repair roof eaves?
The national average cost to repair roof eaves damage runs from $460 to $1,330. Most people pay around $900 to have a carpenter repair a 30 linear feet section of the soffit and fascia damaged by moisture or insects. At the low end of the spectrum, you will pay $180 to repaint a 30 feet section.
How do you fix rotting eaves?
Soffit and Fascia RepairRemove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. ... Remove Rotted Fascia. Remove the rotted section of fascia. ... Remove Old Soffit. Pull down to remove the old soffit. ... Remove Rotted Rafter. ... Attach Cleat. ... Attach New Rafter. ... Seal Replacement Soffit. ... Attach Replacement Soffit.More items...
How do I fix a hole in my eaves?
You might find the easiest option is to replace that sheet of eave lining entirely. That would save the hassle of having to patch the hole. Depending on the size of the hole, you could use a Builders Edge 150 x 150mm Aluminium Plasterboard Hole Patch and cement filler.
How do you replace eave fascia?
0:2216:07How to Replace Fascia and Soffit without removing DRIP EDGE!YouTubeStart of suggested clipEnd of suggested clipPull this fascia out and then we'll get that little piece out of there. So then i can just take myMorePull this fascia out and then we'll get that little piece out of there. So then i can just take my next piece slip it back up there make sure you stick around at the end of the video.
How do you fix the end of rotted fascia?
2:074:27How to Replace a Fascia Board and Repair Water Damage - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat just loosen the gutter. So we can get the fascia board out a small flat pry bar is the perfectMoreThat just loosen the gutter. So we can get the fascia board out a small flat pry bar is the perfect tool for this job one of the nice things about rotting wood is it just lets. Go so easily.
What is the difference between an eave and a soffit?
Soffits can be manufactured from aluminium, wood or vinyl, and it's important to select a material that's suitable for the climate in which you reside. To summarise, an eave is part of a roof system and a soffit is part of the eave. In simple terms, eaves and soffits are two different parts of the same structure.
What kind of wood is used for eaves?
All About Eave Eaves are simple boxes. The bottom -- or soffit -- where the damage is, is typically thin plywood, usually 1/4-to-3/8-inch-thick. It's cut in long sections and butt-jointed together with a thin piece of plastic molding that slips over both ends forming a joint.
Can you replace fascia without replacing roof?
Sometimes you can repair a section of your fascia instead of replacing the entire board. For example, if only a few feet of the board have been exposed to water, your roofers may be able to cut out just that section of fascia, so long as it spans two rafters and can be safely resecured.
What's the difference between soffit and fascia?
The soffit helps regulate your home's temperature, allowing your roof to “breathe.” Cool, dry air is drawn into the soffit vent, and hot moist air is forced out of roof exhaust vents. The fascia is the attractive board along the side of the overhang and the roof that helps your roof appear finished.
Can you replace fascia without replacing soffit?
Companies that repair or replace gutters will typically teach their technicians about the basics of roofing, including soffit and fascia. Whether you're having your gutters serviced or not, a professional will likely need to replace or repair the fascia first, then the soffit and gutters.
How do you fix rotted wood soffits?
The good news is that you won't even need to climb on top of your roof to fix your soffit!Pry off your shingle mold. ... Remove the fascia. ... Remove the soffit's rotting wood. ... Take out the rotted rafter (when applicable). ... Install the new rafter (when applicable). ... Prepare the new soffit. ... Attach the soffit. ... Attach the fascia.More items...•
How do you replace a rafter without removing the roof?
Measure the dimensions of the old rafters beneath your roofing surface. ... Slide one of the newly cut rafter legs into position directly next to the old rafter. ... Slide the new joists into position beneath each of the new sets of rafters. ... Drive nails through the joists and into the new rafters at each end.
Can you repair damaged fascia?
5:168:54Repairing Fascia Board - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey get a little bit thinner. And you can just pull them right out they don't even hold well all ofMoreThey get a little bit thinner. And you can just pull them right out they don't even hold well all of these nails that are in here I just pull them right out now I have large holes the holes are easy
How do you fix a small hole in a soffit?
Patching the Soffit Measure the hole carefully, and cut a patch to fit. The patch should be slightly smaller than the hole, to allow for expansion. Care should be taken to match a tongue and groove patch to the existing soffit. Nail or screw the patch into place.
How do you cover roof eaves?
In some home construction, the eaves are left exposed, which leaves the ends of the roof rafters visible. You can enclose the eaves by installing soffit panels. These are panels made of vinyl or metal that create a solid cover over the eaves.
How do you replace a rafter without removing the roof?
Measure the dimensions of the old rafters beneath your roofing surface. ... Slide one of the newly cut rafter legs into position directly next to the old rafter. ... Slide the new joists into position beneath each of the new sets of rafters. ... Drive nails through the joists and into the new rafters at each end.
How do I fix a squirrel hole in my roof?
Seal All But One Entry Point When Squirrels Aren't Home Some sealing options: Stainless steel mesh, sheet metal, or aluminum flashing can't be chewed through. Use caulk or foam sealant to close up holes.
All About Eave
Eaves are simple boxes. The bottom -- or soffit -- where the damage is, is typically thin plywood, usually 1/4-to-3/8-inch-thick. It's cut in long sections and butt-jointed together with a thin piece of plastic molding that slips over both ends forming a joint. In some cases, the joint may be trimmed out with a thin piece of wood trim.
Reverse Psychology
Insert the tip of a prybar under the ledger board between the exterior siding. Pry it out gently. Remove the prybar and reinsert it 12 inches away from the original insertion point. Continue prying and pulling until the ledger board comes loose from the house.
The Cover-Up
For a quick pick-me-up, try overlaying the plywood under the eave. There are lots of products that will work for this, but it should be exterior grade. Use some type of textured composite for an updated look, go with regular exterior plywood or even textured aluminum.
Replace or Repent
If the plywood under the eves is warped or damaged beyond repair, it's better to replace it. Start by prying off the ledger boards to release the plywood. Pull the sections apart, releasing them from the plastic tracks in the center. Measure, and purchase new exterior grade plywood of the same thickness.
What is the vertical board on the eaves?
That's the name for the vertical board or panel on the front of your eaves. Its complement is the "soffit"—the board that forms the bottom of the structure—and technically, that's the only part that's really supposed to be called the "eave.". The first thing is getting to the eaves, which means using a ladder.
What is 1x6 fascia board?
The common board in use for this purpose in North America is a "1 x 6"—a board whose pre-milling dimensions are one inch thick by six inches wide.
Is it hard to repair a eaves?
Eaves are a vulnerable part of your house, exposed to weather and damage by falling limbs. Luckily, they aren't too hard to repair when the inevitable happens and repair is needed.
Can you replace a section of fascia board?
But if you have damage to a long section of fascia board, you may choose to replace just the damaged portion. That's not easy, because the need to protect the roof decking itself makes it hard to make a complete cut across the fascia board.
What is the repair of eaves 1?
Repairing eaves 1 involves repainting, repairing, or replacing sections of soffit 3 ( the underside of the eave 1 ), fascia (the forward-facing surface of the eave 1 ), or the gutters. Prices can vary based on size, accessibility, and materials. In some cases, replacement materials are supplied in minimum lengths that you may have to cover the cost of, regardless of what you need.
How much does it cost to clean gutters on a eaves?
When the gutters on your eaves 1 begin to overflow they are most likely clogged with leaves and debris. Professional gutter cleaning services cost on average $150. Rotted eave 1, fascia, or soffit 3. Rotting of the eave 1, fascia or soffit 3, may not be instantly recognizable.
What does rotting eaves 1 mean?
Rotting of the eave 1, fascia or soffit 3, may not be instantly recognizable. Peeling paint, cracks, and sagging or overflowing gutters can indicate a deeper problem. Usually, the repair of rotting eaves 1 requires sections of the material to be completely removed and replaced.
What is eaves 1?
Properly designed and installed eaves 1 provide shade and divert water away from features of your home that are vulnerable to moisture damage. Depending on where you live, damage due to weather, age, and/or pests might lead 2 to needed eave 1 repair in the soffit 3, facia, or gutters.
How long does paint last on a roof?
Peeling paint. When peeling paint appears around your eaves 1, it may be simply normal wear and tear, or an indication of a bigger problem. Exterior paint should last approximately seven to ten years. If your paint is significantly younger, or is showing signs of staining in addition to chipping, you may have a leak in the eave 1 or the roof above. A thorough inspection will let you know if you need the help of a professional painter, roofer, or carpenter.
What happens if you leave snow on your roof?
Of course, snow on the roof will continue to melt, creating an ever-growing pool of water. If left unaddressed, ice will continue to build up, putting increased weight on the eaves 1 and gutters, and the water will eventually find its way through the roof surface.
Why are eaves 1 so complicated?
Eaves 1 are complicated because they are vulnerable to elements and made up of a number of components that, once damaged, will cause more damage to other parts of the roof and walls.
How to remove warps from poplar?
Drive a series of 2-inch screws through the poplar, pulling it tight against the fascia to remove warps. Using a drill/driver, drive in one row of screws 2 inches from the top and one row 2 inches from the bottom edge. Examine the bottom edge. If you see spaces between the fascia and the poplar, drive additional screws where needed to close them.
How to install poplar on a house?
Place a piece of 3/4-by-3/4-by-120-inch poplar in the corner on the opposite side of the plywood, flush with the end. Repeat Step 9, installing the poplar on the exterior side of the house.
Can you remove gutters before fixing soffits?
If your fascia has gutters attached, remove them before fixing your soffits . Gutters are a constant source of problems, so consider leaving them off. Warnings. Check the eaves for hornets, spiders or other critters that might have inhabited cracks, gaps or holes.
