Repairing Guides

how to repair electric fireplace heater

by Petra Glover Published 2 years ago Updated 2 years ago
image

STEPS TO COMPLETE:

  • 2 Phillips screwdriver remove four mounting screws from edges of fireplace.
  • Pull fireplace slightly out from its location.
  • Unplug fireplace from outlet and remove fireplace to a location to complete repair.
  • Clean fireplace exterior with damp rags or wipes to remove dust.
  • From the backside of the fireplace remove the 10 screws along the edge of the back panel. Lay back panel down. ...
  • Clean the area removing any dust and debris from the area.
  • Lubricate the motor shaft and rod end at the grommet with WD-40 Lithium Grease or similar lubricant. This is where the squeak comes from.
  • If you only had the squeak to get rid of you can put the fireplace back together at this point by following the steps in reverse order. ...
  • To remove the top panel remove the six screws along the top edge three on each side.
  • Remove top panel.
  • You now have access to the heater fan electrical panel and controller.
  • Blow the heater fan out with canned compressed air.
  • Wipe fan blades and surrounding area clean.
  • Put the fireplace back together by following steps in reverse order.

Full Answer

How do you fix an electric fireplace that won’t heat up?

Turn your electric fireplace off at the unit, and turn it off and unplug the power cable at the wall socket. Leave the fireplace for a period of time to cool down, and then try using it again. Ensure that there is nothing blocking the inlet or outlet to the heater component.

Why won’t my electric fireplace heater turn on?

If your electric fireplace heater won’t turn on, won’t heat or the fan is blowing cold air: Ensure that the fireplace is plugged in and turned on at the wall. Ensure that the main power switch on the fireplace is turned on. On my electric fireplace, the heater switches won’t work and the heater won’t turn on unless the main power switch is on.

Does my electric fireplace need repairs?

Before it’s determined that an electric fireplace needs repairs, some troubleshooting will have to be done to get to the root cause (s) of seeming malfunction. Many areas need to be looked at. These include the breaker, the power supply, and the fuses. Other points to focus on include the light bulb, the manual as well as cleaning the fan.

How do I know if my electric fireplace is working?

Check the Power Because electric portable fireplaces run off electricity, the first place to check is in the power supply when the unit is not working. You can check this in one of two ways. If you have a voltage tester, you can easily check the power outlet for voltage to ensure there is power available in the outlet.

image

Why would an electric fireplace stopped working?

Check the fireplace for any faulty wiring. A tightly bent or over-stretched power cord may be causing the problem. Check your fuse box or breaker for any switches that have tripped. Inspect the fuse on the electric fireplace and replace if necessary.

How do you reset an electric fireplace heater?

SOLUTION: Turn all switches to the “off” position and unplug the unit from the wall for five minutes. After five minutes, power everything back on.

Can you repair an electric fireplace?

Branded electric fireplaces, like the ones that we carry at Stylish Fireplaces, can certainly be repaired outside of warranty. It's one of our criteria for carrying a product line. All of the better brands provide parts so that the fireplaces may be repaired long after the warranty expires.

How do you fix a electric fireplace that won't turn on?

The first thing you should do is check the power source. Make sure that the outlet you're using is working and that your electric fireplace is plugged in correctly. If it's still not turning on, try pressing the reset button on the unit. If that doesn't work, you may need to call a technician.

How long do electric fireplaces last?

10-20 yearsElectric fireplaces can last for 10-20 years depending on how frequently they are used. Many manufacturers offer warranties ranging from 1 year to 10 years depending on the model.

Why does my electric fireplace have no flame?

The most common issues with the flame on an electric fireplace not working can be the need to replace the bulb if no flame effects are being displayed. Issue regarding no movement of the flames or squeaking during operation may be due to a problem with the motor or the rod.

Can you replace the bulb in an electric fireplace?

Replacing your electric fireplace light bulb is simple and easy. You don't have to be mechanically inclined to pull this one off. In most cases, all you'll need is a screwdriver and some replacement bulbs to get you and your family back to enjoying movies around the fireplace.

How do I reset my fireplace?

0:041:37How to Reset IPI on Your Gas Fireplace - IntelliFire Ignition SystemYouTubeStart of suggested clipEnd of suggested clipSo if you have a insert a gas insert which has a surround on it on the right hand side of theMoreSo if you have a insert a gas insert which has a surround on it on the right hand side of the surround towards the bottom there's a switch all you do is hit the switch.

Where is the light bulb in an electric fireplace?

Where Is The Bulb In An Electric Fireplace? The bulb in an electric fireplace is typically located within the center of the unit. The access cover, typically located at the back of the unit, will need to be removed in order to reach the bulb.

How do I reset my fireplace?

0:041:37How to Reset IPI on Your Gas Fireplace - IntelliFire Ignition SystemYouTubeStart of suggested clipEnd of suggested clipSo if you have a insert a gas insert which has a surround on it on the right hand side of theMoreSo if you have a insert a gas insert which has a surround on it on the right hand side of the surround towards the bottom there's a switch all you do is hit the switch.

How do I reset the thermostat on my infrared heater?

1:343:01How To Repair Your Infrared Quartz Heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut you'll want to take a little screwdriver. Or something down in there and push center button andMoreBut you'll want to take a little screwdriver. Or something down in there and push center button and it'll reset your thermostat.

How do I reset my twin star electric fireplace?

To manually restart Turn the power supply on the stop and disconnect the unit from the wall socket for 5 minutes. After 5 minutes, turn the unit back on to the wall socket, and it works as normal.

How do you reset an infrared quartz heater?

How Do You Reset An Infrared Heater?The first thing to do is unplug the heater from the electrical outlet.Next wait for about five to ten minutes for the unit to cool down.Once cooled down, plug the cord back into the wall socket.You can now switch the heater on.The heater should start operating as usual.

How to tell if a fireplace is not turning on?

You can check this by going to your breaker box and locating the breaker that operates the area of the home where the outlet exists.

How to check if a portable fireplace is working?

1. Check the Power. Because electric portable fireplaces run off electricity, the first place to check is in the power supply when the unit is not working. You can check this in one of two ways. If you have a voltage tester, you can easily check the power outlet for voltage to ensure there is power available in the outlet.

What does a fuse look like on a fireplace?

Depending on your make and model, this might be located in a different place; however, many keep them in the back. The fuse will look like a clear cylinder with a filament inside. If the filament is broken (a likely indicator of why your fireplace is not working) it will look black or gray.

Why is my fireplace fan not working?

The fan can become dirty, and it needs to be cleaned to ensure it functions properly. A build-up of dirt and debris could prevent the fan from spinning properly and lower the effectiveness of the fan.

When will electric fireplaces be available in 2021?

on May 12, 2021. Electric portable fireplaces are a convenient way to warm a room, barn, patio, deck, or any other area. A portable fireplace allows you to heat a room where a traditional fireplace is not an option. Also, the portable fireplace adds ambiance, visual appeal, and warmth to any space.

Do electric fireplaces have fuses?

Electric portable fireplaces have fuses in them that must be functional for the fireplace to heat properly. If the fireplace has lost its ability to heat, check the fuses to see if they are burned out before replacing pricier parts or the whole unit. The fuses are inexpensive and easy to replace.

What is the purpose of articles being reviewed?

To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience.

What to do if your electric fireplace won't turn on?

If your electric fireplace still won’t turn on: Ensure that the fireplace isn’t located in a confined space, is free of any obstructions and the components are clean.

How to tell if a fireplace heater is shutting off?

Ensure that the dial is set above the current room temperature or the fireplace heater will keep shutting off. The thermostat dial will make a ‘clicking’ sound when turning to let you know what the current room temperature is.

Why does my electric fireplace make a clicking noise?

An electric fireplace makes a clicking noise when the thermostat dial is turned to the current temperature in the room . Your electric fireplace may be making a clicking noise as the temperature in the room rises above and falls below the temperature set on the thermostat.

Why does my electric fireplace turn back on?

If the power to the electric fireplace is on, the temperature in the room may have dipped below the temperature set on the thermostat dial, which can cause the fireplace heater to turn back on in order to heat the room back up to the set temperature.

Why do electric fireplaces have overheat protection?

Many electric fireplaces also come with an overheat protection mode as a safety feature to prevent the fireplace from overheating.

What does it mean when the thermostat is turned to the left?

Turning a thermostat dial to the left typically decreases the temperature setting, while turning it to the right increases it. Lowest thermostat setting. Highest thermostat setting. An electric fireplace thermostat will typically make a ‘clicking’ noise when the dial has been turned to the current room temperature.

How does an electric fireplace reflect light?

Like many other freestanding electric fireplaces, my electric fireplace reflects light onto the back of the fireplace screen from a rotating rod that has strategically placed mirrors along it .

How to stop an electric fireplace from overloading?

Check your homes electrical panel to make sure that you haven’t tripped a breaker. When your circuit is overloaded, the breaker will flip off as a safety precaution. If you have several large appliances running on the same circuit as your electric fireplace, this can overload the circuit. Plug your electric fireplace into a separate plug or move other appliances to a different outlet.

Where is the on/off switch on an electric fireplace?

Electric fireplaces are turned on by an on/off switch which is usually located near the edge of the fireplace in a discreet location. Feel around for any buttons or switches. Most units also come with a remote.

Why does my electric fireplace freeze?

The other case is that the flame on your electric fireplace is powered by a motor that creates movement. When a wire comes loose or the motor stops functioning , the flame will freeze. Check the wiring to make sure that all connections have good contact. Look for exposed and frayed wires.

How much does a 37.5 inch fireplace cost?

The 37.5″ Acadian Walnut Electric Fireplace from Dimplex allows you to frame pictures directly into your fireplace mantel! How cool is that! $599.00.

How to fix a thermostat that is not working?

Check electrical wiring and look for any loose connections. Make sure that the wire running to your thermostat is properly attached. Sometimes this wire can break free from the connector. In this case, you can re-solder the wire to the connector. This is a pretty simple fix if you are the handy type (shouldn’t take more than 5 minutes).

What to do if your remote doesn't work?

When the remote doesn’t work (and the batteries aren’t dead of course), the problem usually lies with the circuit board. Contact your manufacturer to order a replacement remote control. Check your homes electrical panel to make sure that you haven’t tripped a breaker.

Do electric fireplaces wear overtime?

Time for a new electric fireplace? Like any mechanical device, electric fireplaces will gradually wear overtime. Why worry about the headache and expenses of fixing your fireplace? Prices on electric fireplaces have dropped dramatically in the past few years. Visit Portable Fireplace.com today!

How to check if a flame generator is running?

Open the back panel of the unit. Check whether the spinner spindle is connected to the motor and that the flame generator drive motor is running. If it's not, call customer service.

What to do if your wire is shorted?

The wire has short circuited. Plug the unit into another outlet or install a dedicated 15-amp circuit.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9