
- Determine the Problem. Before doing repairs on the electrical coil, you need to properly diagnose the problem first. ...
- Remove the Housing to Reveal the Electric Coil. To get to the electric coil, you need to remove the coil housing. ...
- Note the Position and Configuration of the Coils. ...
- Remove the Wire from the Tabs. Carefully remove the wire completely from the tabs on the brush pads. ...
- Check the Insulation. Before rewinding the wire, check the insulation. Repair burned or damaged insulation using insulating tape.
- Rewind the Coil. Using the same gauge and type of magnet wire that was on the original electric coil, rewind the electrical coil carefully back to its ...
- Reassemble the Coil Housing. After rewinding the coil, reassemble the housing and replace the screws that you removed earlier. ...
Full Answer
How do I fix a broken lighter?
The first step is diagnosing what is wrong with your lighter, and then you can get to work fixing it. Don't get frustrated if it doesn't work immediately - check all potential problems before you give up. If your lighter has sentimental value you may be able to get it working again.
How to repair an electrical coil?
To repair your electrical coil, here is what you should do. Before doing repairs on the electrical coil, you need to properly diagnose the problem first. To do this, open the housing of the electrical coil and check the coils for signs of wear and tear, dust, grime, and corrosion on the coil or on the housing.
What to do if your cigarette lighter won't light?
If it won't spin, it won't light. If there is only dirt and debris inside the lighter you might be able to clean it out with your fingers or a pipe cleaner and get it going again. Check the fuel tank. Luckily the most common problem with these lighters is their incredibly small fuel tank.
Why won't my lighter light?
If you broke the plastic part of your lighter then you'll need a new one. The pressure is compromised and you won't be able to use it anymore. Look for rust, debris, or dirt. If you've left a lighter outside for a long period of time the metal wheel on top might be rusted in place. If it won't spin, it won't light.

Can you fix an electric lighter?
Sometimes a lighter can get stuck or broken. Generally it's a quick fix, but it's also very easy to buy a new one. The first step is diagnosing what is wrong with your lighter, and then you can get to work fixing it. Don't get frustrated if it doesn't work immediately - check all potential problems before you give up.
Why is my electric lighter not working?
If your lighter is not turning on, it is most likely because the Child Safety Lock was triggered or activated. The lock will need to be deactivated before the lighter can be used. To de-activate Child Safety Lock, press ignition button three times rapidly or until the blue indicator light flashes three times.
How do you clean an electric lighter coil?
To clean your lighter's plasma electrodes, you'll need a cue tip and a solution of alcohol or ethanol. Soak your cue tip with alcohol and rub back and forth gently against the prongs to get rid of any ash, tar, or debris deposits. Wait until all parts of the unit are completely dry before your next use.
How does an electric coil lighter work?
Once you push the button on the lighter, it gives out enough energy in the air to make it ionized. Due to ionization, the electrons present in the air start moving along the nucleus and create current in the form of an arc. This is why they are also called electric and arc lighters.
How do you make a lighter work again?
0:000:40How To Revive a DEAD LIGHTER! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWithout making it spark. After a few minutes you'll gather a small amount of Flint. Bunch it upMoreWithout making it spark. After a few minutes you'll gather a small amount of Flint. Bunch it up together and twist the tissue with the Flint inside. Now using the lighter spark up the tissue.
Do electric lighters wear out?
It never runs out of fuel because it uses electricity, it never needs to be thrown out because it's rechargeable, and it never blows out in the wind because it uses plasma arcs instead of a traditional flame to ignite.
How do you fix a jet lighter that won't spark?
Make sure that there is no debris, dirt or lint clogging or blocking the lighter's operation. Even a small amount of debris can stop a lighter from functioning correctly. Exercise care when checking for blockages and keep your fingers well away from the igniter.
What happens if you touch electric lighter?
A: Touching the electric arcs will feel like a sharp bite or the shock you get from static electricity, but about 10 times stronger. It will definitely wake you up! We do not recommend touching the arcs. However, if you do, there is no permanent damage other than a few small red marks on your skin.
Can electric lighters explode?
"With the lighter exposed to hot temperatures, the fluid and gases inside the lighter expanded, causing internal pressure to rise," Dr Wiesner said. "That increases stresses in the container of the lighter, and then it ruptured — and that would've caused the mechanical explosion of the lighter.
How does an electric lighter make a spark?
When the button on a Piezo electric ignitor is pressed, a spring loaded hammer strikes quartz in order to create a spark. This is the typical process used in such lighters. This creates the necessary amount of voltage to generate a spark. Piezoelectric devices are much longer lasting than devices that depend on flint.
Are electric lighters worth it?
The best electric lighters are also more economical and environmentally friendly. Regular lighters have to be refilled with lighter fluid; the cheaper ones you usually toss out. But electric lighters can be easily recharged to let you use them again and again.
Can you use electric lighter for cigarettes?
For cigarettes, you can use pretty much any electronic plasma lighter. But for cigars, especially for the larger ones, not every electric arc lighter is convenient to use.
How do you fix a lighter that won't spark?
My Lighter Hisses But Won't LightMake sure that there is no debris, dirt or lint clogging or blocking the lighter's operation. Even a small amount of debris can stop a lighter from functioning correctly. ... Check the flame adjustment of your lighter. ... Check the flame height on your lighter.
How do you fix a cigarette lighter that won't work?
Use the fuse gripper tool included in the fuse box (or your fingers) to pull out the fuse. If the metal on the fuse looks broken or burned, it will need to be replaced. Buy a new fuse of the same amperage from your dealer or auto parts store and replace the bad fuse. Once installed, try the cigarette lighter again.
Where is the fuse for cigarette lighter?
0:404:023 things to check when your cigarette lighter socket stops working (car ...YouTubeStart of suggested clipEnd of suggested clipFind fuses go to that page and locate the power outlet fuse this owner's manual shows there are twoMoreFind fuses go to that page and locate the power outlet fuse this owner's manual shows there are two fuse panels one in the passenger. Compartment.
What happens if you touch an electric lighter?
A: Touching the electric arcs will feel like a sharp bite or the shock you get from static electricity, but about 10 times stronger. It will definitely wake you up! We do not recommend touching the arcs. However, if you do, there is no permanent damage other than a few small red marks on your skin.
How to remove wind coils?
Carefully remove the wire completely from the tabs on the brush pads. Count the number of winds in each coil as you remove the wire. Be careful not to bend the taps too much when removing the wires to avoid damaging them. After removing the wire, cut the coils of the wind at the top of the armature.
What is the purpose of electrical coils?
Electrical coils are usually wrapped with insulating tape or coated with varnish to provide insulation. To secure them in place, electric coils are often held together by electrical tapes and placed in secured housing.
How to wind a wire?
On your first wind, leave the end of the wire loose on the tab. When winding the wire, make sure that you follow the exact winding patterns and number of winds as the original. To complete the job, connect the end of the last winding to the loose end of the first wind.
Can you replace an electrical coil after a repair?
If the electrical coil is physically damaged, you have to replace it. On the other hand, if the electrical coil is physically intact, it may still work well after a repair so get your tools ready to rewind the coil.
How to fix a lighter that is not working?
The first step is diagnosing what is wrong with your lighter, and then you can get to work fixing it. Don't get frustrated if it doesn't work immediately - check all potential problems before you give up. If your lighter has sentimental value you may be able to get it working again. Steps.
How to refuel a lighter?
To refuel, turn your lighter upside down and put pressure on the fill valve with the butane can nozzle. Once the nozzle is inside, apply pressure until you feel the metal of the lighter get cold. Make sure to keep your lighter away from your face and anything flammable.
What to do if your lighter isn't working?
If your lighter isn’t working, check to see if the fuel tank is empty or the flint is gone, as these are simple to fix. Before you refuel your lighter, purchase a butane can, which can usually be found at a local hardware store.
How to clean a lighter that won't spin?
If it won't spin, it won't light. If there is only dirt and debris inside the lighter you might be able to clean it out with your fingers or a pipe cleaner and get it going again.
How to replace a butane lighter flint?
It's tiny black cylinder about a quarter inch long. To replace the flint, remove the metal surrounding the flame and the spark wheel. You'll have to twist it out of position .
Step 1: So What You'll Need for This
Tools - a small philips head screwdriver (the tiny ones) it almost alway philips head. -a penknife or a small flathead screwdriver (for adjustments) -a pair of pliers, needle nose are great her but I can do it with my fake leatherman start to finish (make damn sure the pliers aren't magnetized it's annoying) -a safety pin or some thin tough wire or a drawing pin (you'll see what I mean if it comes up) Materials -some sturdy wire about 24awg (anything that fits will do (again you'll understand pretty quick) is handy -lighter gas, really helps diagnosis, in fact try the first... -You may need rubber tubing or a piezo spark depending how you broke it (if you dropped I already know whats wrong.
Step 2: Ok Diagnosis Time Doctor
First put gas in the lighter, you should have done this already but this helps us determine alot. Fill it with gas and listen, it may leak for a up to 30 seconds but that's ok as long as it stops. Push down the button, is there gas coming out and is there a definite click from the spark (if yes to both this will be easy) If there's no gas coming out at the nozzle but it's going somewhere then the connection has been broken probably nothing more than the flexible gas line has slipped off the seat of the reservoir end (there's more room here so it fall off that end but it's easy to fix anyway) If you push the button all the way down and no click go to the shop and buy a really crappy cheap electric lighter, not a bic though, their piezios have no wire. try turning down the gas a bit (sometimes the gas can't ignite because it going too fast for the tiny arc to heat...
Step 3: Opening Your Lighter Up
This step just tells you how to take it all apart. First look on the bottom, there should be a small (mostly likely philips head) screw not far from the filler valve, unscrew it, usually that is the only thing holding a lighter together, now pull the casing down off the rest (hold on to the cap and carefully pull the casing off) now you should see the guts of your lighter, there's probably 2 pins holding the assembly together.
Step 4: Adjusting the Spark
This is easily the most common problem with jet lighters because they have metal bodies... Basically the piezo is grounding out to the body or the chassis... All we need to do is move the wire out and put it against the nozzle so it's touching it, that'll be guaranteeing near 100% performance in lighting.
Step 5: So I Did That, But I'm Not Getting Anywhere
Simply check where gas is going by pushing down on the lever for the gas valve on the reservoir, look carefully along the gas line, you should see something similar to 'heat wiggles' (from the change in desity between gas and air) if theres a leak, I you have a crappy BBQ lighter kicking around then cannibalize that for some gas line (there's enough for five or six replacements) and if you needed it they're a great source of igniters due to the extra long cable. If the gas still isn't getting out the nozzle then the nozzle's clogged, symptoms include the lighter bursting into flame for a second during use.
Step 6: Putting It Back Together
Right now we rebuild the lighter From the picture you should be able to tell your own parts easily enough. This list goes bottom to top in stacking up the components again, refer to the pictures to make full sense BOTTOM - Reservoir -gas valve lever (best put in before piezo for convenience -piezo -button cover/s -lid top assembly (make sure the gas tubes go back in the right place) -slide the cover back on and screw on.
Step 7: I Do Believe We're Done
Again if there's anything I missed or any questions comment me and I'll do my best to help.
How to keep torch lighters firing?
Clean Your Lighter. For best results you’ll want to polish all of your torch lighters with essential oils and then dry them with a Mulberry silk cloth before locking them in an air-tight vault each night. Okay, I kid, I kid, but it’s no joke that cleanliness is key in keeping your torches firing strong and long.
What to use in a refillable torch?
1. Only Use High Quality Butane. When selecting a butane to use in your refillable torch you want to steer clear of the stuff in the yellow bottle at your local drugstore. In fact, you never want to use anything less than a triple-filtered butane (like this one.)
Why won't my cigar lighter stay lit?
If your lighter gets air in the line, that can cause the flame to flicker, sputter, or possibly fail to stay lit . It may also mean the torch won’t fire when you press the button the first time. And if you are trying to light your cigar, nothing is more frustrating than having to mess around with a temperamental lighter.
How to bleed a lighter?
Here’s how you do it…. Step 1 – Hold the button down on your lighter until the lighter is completely empty. To make sure there’s nothing left, listen for the sound of hissing air.
How to avoid air pockets in lighter?
It can be a bit tricky at first, but here’s how you can reduce the risk of air pockets when refilling: Step 1 – Resist your natural impulses and do not shake the can of butane before filling your lighter.
Does butane burn cleaner?
Purer butane burns cleaner and prevents clogging of your lighter’s torch nozzle. A clogged nozzle, and the lack of flame it causes, is effectively the death knell for most torch lighters. Prevent this tragedy by using good butane! Personally, I recommend Colibri Premium Butane.
