- Close off the drain. Before you start fixing the faucet, it’s a good idea to shut it off as well as close the drain tightly.
- Loosen the screw on the faucet’s handle. To separate the handle from the valve stem, you need to look for a hole with a fixed screw in it. ...
- Lift the handle off. If you’re lucky, then at this point, you can effortlessly prise off the handle by hand. ...
- Remove the brass nut. To do that, use a crescent wrench to loosen the brass nut underneath the faucet stem. ...
- Add grease to the faucet’s inner workings. By now, you can easily take out the cartridge, which refers to the inner part of the faucet stem. ...
- Reassemble the faucet handle. To put all of the components together, first, you need to put the faucet cartridge back at its original position.
How do you fix a faucet that won’t turn on?
Tighten the nut, and then replace the faucet handle. Tighten the screw that fixates the handle, and then check the handle. The handle should be moving normally, and now you can turn on the water supply once more and continue on with your day. Faucet handles that do not rotate the correct way can be frustrating.
How do you fix a two handle cartridge faucet?
Follow these steps to fix a two-handle cartridge faucet. Unscrew the set screw to remove the handle. Remove the retaining clip or nut. Reassemble the faucet. With the faucet knobs in the “on” position, slowly turn on the water supply. Too much initial pressure can damage the new hardware.
Do you have to replace the handle on a bathroom faucet?
You may have to replace the handle, but not the entire faucet. If the Allen screw is stuck, or if you strip it so it won’t come out, remove the cap with the handle still in place.
How do you fix a leaky ball faucet?
Follow these instructions for repairing a ball faucet. Loosen the set screw and take off the handle. Use a wrench to remove the cap. For leaky spouts, remove the cam, washer and ball. Use a small screwdriver to remove the seats and springs. To repair leaks at the base, remove the spout and replace the O-rings.
What happens if you loosen a faucet handle?
How do I fix a shower handle?
Where is the setscrew on a faucet?
About this website
How do you fix a broken faucet handle?
0:050:48Bathroom Repair : How to Repair a Sink Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's an allen wrench right inside of here that you're going to loosen. And this handle will pullMoreThere's an allen wrench right inside of here that you're going to loosen. And this handle will pull right off.
How do you fix a bathroom faucet handle?
0:192:47Bathroom faucet handles loose/wobbly - DIY fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipProject what you want to do is go to your handle. And locate your actual allen screw in our case onMoreProject what you want to do is go to your handle. And locate your actual allen screw in our case on the cold is right there.
How do you take apart a single handle kitchen faucet?
0:423:11How to Repair a Leaky Single Handle Ball Kitchen Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis may require using an allen wrench to loosen the hammer. There may be a button that covers aMoreThis may require using an allen wrench to loosen the hammer. There may be a button that covers a screw that needs to be removed first and then you can loosen the screw and remove the lever handle.
How do you take apart a bathroom faucet handle?
0:301:32Handles: Repair and Replace (2 Handle Bathroom Faucet) - YouTubeYouTubeStart of suggested clipEnd of suggested clipScrewdriver. Now use a Phillips screwdriver to unscrew and remove the handles from the cartridge.MoreScrewdriver. Now use a Phillips screwdriver to unscrew and remove the handles from the cartridge. Place the new handles on and tighten using the Philips screwdriver. Finally pop the caps back.
Can you just replace faucet handles?
You don't have to be an experienced plumber to replace a bathroom faucet handle as long as you have the proper tools and can follow some easy directions. Many people put off this DIY project, listening to the dripping night after night.
How do you take apart a faucet handle?
0:003:44How to Remove a Faucet Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you can't close the drain cover it up use a small screwdriver to pry the button off of the top ofMoreIf you can't close the drain cover it up use a small screwdriver to pry the button off of the top of the faucet.
How do you fix a kitchen faucet that pulls?
0:442:51How to Replace a Hose in Your Pull Out Kitchen Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the weight on the hose. Thread the hose into place until it's tight and secure it with aMorePlace the weight on the hose. Thread the hose into place until it's tight and secure it with a quarter turn with a wrench follow these steps if your host style is quick disconnect.
How do you remove a screwless faucet handle?
Once you find the necessary tools, you'll need to follow these steps to remove the screwless faucet handle successfully.Step 1: Turn off the water. ... Step 2: Remove the cap on top of your faucet. ... Step 3: Remove the hidden set crew. ... Step 4: Remove the faucet handle. ... Step 5: Rinse off mineral deposits.
How do you remove a screwless faucet handle?
Once you find the necessary tools, you'll need to follow these steps to remove the screwless faucet handle successfully.Step 1: Turn off the water. ... Step 2: Remove the cap on top of your faucet. ... Step 3: Remove the hidden set crew. ... Step 4: Remove the faucet handle. ... Step 5: Rinse off mineral deposits.
Why is my faucet handle loose?
It's usually a result of wear and tear on the faucet stem, or cartridge. The cartridge attaches to the handle and the two components work together to control the water flow. When the stem becomes stripped, the handle will feel loose or just spin on end.
How do you remove a faucet handle without a set screw?
You can use an allen wrench (also called an allen key) to remove it. Once you've done that, you can typically just lift the faucet handle off. However, if it has a cartridge inside, you may need to unscrew a top piece as well to be able to remove the cartridge.
The handle on my kitchen faucet keeps coming loose. What can I do ...
With time and use, the set screw on a handle may loosen up. Using a hex wrench will allow you to re-tighten the set screw in the handle. Your faucet came with the correct hex wrench. If you can’t find the hex wrench that came with your faucet, most single handle kitchen faucets will use a 1/8th inch wrench, while most two handle kitchen faucets will use a 3/32nd inch wrench.
Techniques for solving a tough faucet problem
Repair a drippy ball-type faucet using these pro tricks to deal with stubborn screws. You may have to replace the handle, but not the entire faucet.
Kitchen Faucet Repair: Loosen a stuck screw on a single-handle faucet
If the Allen screw is stuck, or if you strip it so it won’t come out, remove the cap with the handle still in place. You can’t grab the flattened edges with the handle in place. Instead, for this kitchen faucet repair, cushion the jaws of pliers and grip the round edge below.
How to Remove Faucet Handle
If you can’t loosen the Allen screw on the handle of a ball-type faucet, don’t let that 15¢ screw force you into a $100 faucet replacement… just yet! Normally you have to remove the handle to get the worn rubber seats that cause the drip (Figure A). First try spraying the screw with penetrating oil every day for a week.
Required Tools for this kitchen faucet repair Project
Have the necessary tools for this DIY kitchen faucet repair project lined up before you start—you’ll save time and frustration.
Required Materials for this kitchen faucet repair Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
Why Is A Faucet Handle Hard To Turn?
There are a couple of causes that can result in hard-to-turn faucet handles. One of the main culprits is mineral deposits that build up and begin to cause issues. Another possible reason lies in the faucet’s cartridge, which can eventually develop problems that make the faucet handle hard to turn.
Can You Use WD-40 On A Faucet?
Yes, you can try WD40 on a faucet. In this case, where the faucet handle is not wanting to turn, try using a little squirt of WD-40 to see if it fixes the problem. WD-40 will help lubricate the faucet handle, hopefully encouraging movement. This may help loosen the handle to the point where it is more fluid and easy to turn.
How Do You Loosen A Stiff Faucet Handle?
Loosening the stiff faucet handle will take a bit of time, but it is not hard to do. First, you need to examine the interior of the faucet to confirm the problem. From there, you can determine the best course of action.
Putting It All Together
Once you have cleaned the cartridge or purchased a new one if necessary, you need to reinstall each of the parts. Replace the cartridge according to the original orientation. Tighten the nut, and then replace the faucet handle.
Which Ways Should Faucet Knobs Turn?
The type of model will determine the faucet’s on/off directions to regulate flow. Generally speaking, cross handles typically turn in the same direction. This means counter-clockwise to turn on the flow and clockwise to turn off the flow. Think of it as tightening or loosening a nut on a bolt.
Why Do I Need To Fix Faucets That Do Not Turn The Right Way?
If a faucet’s turning orientation is incorrect, it is best to fix it. For example, Moen faucet handles have a temperature limiter. When it reaches below its bottom limit, the faucet handle might have issues with its stopping point, which can cause the handle to move in the wrong direction.
How To Fix Faucet Handles That Turn The Wrong Direction
Fixing wayward handles is a relatively simple task that will take a small chunk of time to complete.
How to Fix a Dripping or Leaky Double-Handle Faucet
Learn how to repair three types of double-handle faucets: ceramic disc, compression/reverse-compression and cartridge.
Repairing Different Types of Faucets
Keep in mind that some cartridge bodies and ceramic disc bodies/cylinders can look similar. In most cases, the cartridge body doesn't have moving parts. The ceramic disc body/cylinder does have moving parts that pivot to open the ports on the bottom.
Locate the Leak
Determine which side of your faucet is leaking by shutting off the water supply valves one at a time. If the leak doesn’t stop after the first valve is turned off, it’s the other line that’s leaking.
Ceramic Disc Faucets
This type of faucet uses a cylinder with tiny discs on the bottom that control water flow. The most successful repair typically replaces the entire cylinder.
Compression & Reverse-Compression Faucets
In this repair, you’ll replace the washer and O-ring or gasket on the valve stem, as well as the valve seat in the faucet.
Aerator
After reassembling your faucet, run the water for a few minutes to clear debris from the new parts. Replace the aerator.
How to Fix a Dripping or Leaky Single-Handle Faucet
Learn to repair three types of single-handle faucets: ball, cartridge and ceramic disc.
How to tighten a headgear nut?
1. Screw the headgear nut back on using a spanner. Locate the headgear nut and place it back to its original spot. Make sure the handle is in its original placement before you tighten the screw. Turn the spanner towards the right to tighten the screw.
How do I fix a leaking faucet handle?
First, turn off your water supply at the valve under the sink and open the faucet to drain any water from the pipe. When the water’s stopped, remove the faucet handle.
What is the O ring on a faucet?
The “O” ring is a piece of rubber that sits under the headgear nut. A damaged “O” ring is the cause of a leaky faucet handle. Stretch the ring off the spout and pull it out of the faucet. Keep the “O” ring in case you need it to identify what size replacement ring you will need. [7]
Why does my faucet make a dripping noise?
The annoying drip of a leaky faucet handle can cause higher water bills and make an irritating dripping noise. Luckily, it's quite an easy problem to fix yourself. A leaking handle is normally caused by a damaged “O” ring inside the faucet.
How to stop water from gushing out of faucet?
This will stop water from gushing out of your faucet when you unscrew it later. Press the off switch on your water main box to turn off the water. Alternatively, look under your sink for a small valve.
What does it mean when a faucet leaks under the handle?
If you notice a leak under the handle of your faucet, you may have a faulty seat washer. Purchase a leak repair kit for your particular type or brand of faucet, follow the instructions, and use the included parts to take care of this type of leak.
How to put an O ring on a spout?
The new “O” ring needs to go in the same place that the original was sitting. Place the “O” ring on top of the spout and use your fingers to push the “O” ring down onto the spout. "O" rings can stretch if they've been in use for a long time.
How long does it take to fix a faucet handle?
The good news is that like a number of sink issues, a DIY faucet handle fix can be completed in just 10 minutes with nothing more than a couple screwdrivers, a wrench, and about $20.
How do I take care of a bathtub?
If you’re taking care of a bathtub, you’ll generally need to turn off your home’s main water supply. We also recommend covering your drain; it’s an easy-to-miss step that can result in screws and other items being lost forever. 2. Remove faucet handles or cover plates.
How do I shut off the water supply in my kitchen sink?
Turn off the water (and cover the drain!) If you’re working on the sink, you can usually find the valve and handle right below it or within the the cabinet it’s built into. Turn the handle clockwise—righty-tighty—to shut off the water supply.
Can you remove a faucet with a pipe wrench?
On most models, removing the faucet reveals a locking nut that secures the cartridge; this can be removed with nothing more than a pipe wrench. Note that there is a small brass screw on the top of the cartridge; we recommend removing this and setting it aside as not all replacement cartridges will include a new screw. 4.
Can you lift out an old cartridge?
With the locking nut off, the old cartridge can be lifted right out (if there’s resistance, that’s not uncommon. Just reach for the pliers). If you don’t already have the replacement, a trip to the hardware store is in order; bring the old cartridge for comparison to make a foolproof purchase.
What is a setcrew on a faucet?
Some handles have setscrews on the side or rear. Others have a decorative cap (usually plastic) that conceals a screw that secures the handle. Your faucet may also have a removable lever that unscrews from the handle base to allow easy access to the handle setscrew. If your faucet has a decorative cap, pry off the cap with a small flathead ...
How many tabs does a faucet cartridge have?
Note the orientation of the faucet cartridge. You must reinstall the new cartridge in exactly the same way. Most cartridges have one or two tabs that fit into notches on the faucet body.
What is a compression type faucet?
If you have a very old two-handle faucet, it may be a compression-type rather than a cartridge. You'll know when you remove the faucet handle: Cartridges are usually plastic and are held in place with a metal retaining nut; compression faucets usually have a metal valve with a flat rubber washer on the bottom.
How to loosen a cartridge retaining nut?
Loosen the cartridge retaining nut, using a pipe wrench or tongue-and-groove pliers. Unscrew the nut all the way and remove it from the faucet body. Note the brass screw at the top of the cartridge, if there is one. Its purpose is to reinforce the cartridge shaft when the faucet body's setscrew is tightened against it.
How to get water out of a faucet when shut off?
Once the water is shut off, open the faucet fully to release any pressure in the water lines and let any water drain out. If your shutoff valves have levers instead of knobs, rotate the levers until they are perpendicular to the water pipes or tubing (the direction of the water flow).
What do new cartridges include?
New cartridges typically include new rubber O-rings for the cartridge. If desired, also pick up some plumber's grease for the O-rings. This makes it easier to insert the cartridge into the faucet body and is an especially good idea if the old cartridge was difficult to remove. Home-Cost.
What is a two handle faucet?
Most bathroom faucets that have two handles are cartridge-style faucets. Each faucet handle (hot and cold) has its own cartridge, a valve that turns with the handle to control the flow of water into the faucet spout. If you have a very old two-handle faucet, it may be a compression-type rather than a cartridge.
Things You Need To Fix A Squeaky Faucet Handle
Here is the list of necessary items to prevent your faucet from producing unpleasant, high-pitched noises:
6 Steps To Fix A Squeaky Faucet Handle
Before you start fixing the faucet, it’s a good idea to shut it off as well as close the drain tightly. This is because if you happen to let excess grease go down the drain, it will float around, solidify, and cling to your pipes.
Conclusion
After reading your step-by-step guide, you already have a thorough grasp of how to fix a squeaky faucet handle. We hope you will soon get the hang of this straightforward procedure with a bit of practice.
What happens if you loosen a faucet handle?
A loose faucet handle will gradually grind away the valve stem that it's screwed to, and should be tightened. Here's a trick to use if the stem is already badly worn.
How do I fix a shower handle?
How to Fix Shower Handle: Use Teflon pipe thread tape. If tightening doesn't work, the stem inside the handle may be worn, especially if it's plastic. Here's a trick to tighten worn stems on most types of faucets: Wrap the stem tightly with Teflon pipe thread tape and slip the handle back over the stem . In most cases, a single wrap creates ...
Where is the setscrew on a faucet?
With some faucets, you'll have to pry off the metal button at the center of the handle. With others, you'll find a setscrew near the base of the handle. Setscrews usually require a hex (or “Allen”) wrench. 10 Tips for Installing a Faucet the Easy Way.
