how to repair fiberglass jet ski hull

^{Repairing a Hole in a Fiber Glass Jet Ski Body}

1. Repairing a Hole in a Fiber Glass Jet Ski Body. ...
2. Begin by sanding both sides of the hole surface with the rough sandpaper until the larger pieces of old fiberglass are smooth.
3. Use the Acetone and a paper towel to clean both sides of the hole and be sure to remove any dirt from the surface.
4. On the back side of the hole take your fiber glass mat and size out the piece of material needed to cover the hole.
It's time to mix the resin and hardener together. Read the specific instructions on the back of the container to get the accurate ratio of resin to hardener.
With the throw away paint brush begin to apply the resin to the back side of the hole directly on the cleaned surface.
After the first layer has been entirely soaked in resin, the next layer can be placed on top of it. ...
Allow the layers to dry for the recommended amount of time listed of the back of the resin container.
Once dry, it is time to move onto the front side of the hole. ...
After you have again mixed your resin, begin by applying a small layer to the inside of the hole only.
Once dry, confirm that the resin has fully hardened. Use the sand paper to sand the resin surface and existing surface to create a seamless finish.

How to repair a jet ski Hull?

Repairing a jet ski hull is possible at home as a DIY by sanding around the hole, placing layers fiberglass mat, and then hardening fiberglass resin around the mat. Even large holes can be taken care of with only a moderate amount of effort. All of these products are available at your local hardware store.

Can you repair a fiberglass jet ski?

Jet ski repairs Do-It-Yourself Fiberglass Repair on Jet Ski Hull Damage to the hull on a personal watercraft (or jet ski) is a common occurrence for many people. Here is a handy guide to help jet ski owners easily perform DIY repairs.

How do you repair a cracked fiberglass boat hull?

You will also need a tool to grind out the wall of the hull around the crack. The best fix is to grind it down and then fill in the valley left from the grinding with flayers of fiberglass mat and hardened epoxy resin. The difference between the two repairs is that a crack is a one-side repair, whereas you repair both sides of the hull for a hole.

What type of fiberglass resin should I use for my jetski?

We recommend the epoxy type of fiberglass resin because it is the strongest and is made to bond well with fiberglass. The hull of the jetski is made of polyester fiberglass or a SMC (sheet molding compound). If punctured or damaged in any way, the fibrous material of the hull can grow and attach contaminants.

How do you fix a fiberglass hull on a jet ski?

1:477:41Jet Ski hull repair DIY - Part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's no way we can glue this stuff together and put the fiberglass on top it's just not going toMoreThere's no way we can glue this stuff together and put the fiberglass on top it's just not going to work that way just looking pretty good so far I cleaned up the area sanded. It down.

How do you fix the hull damage on a jet ski?

1:126:04Personal Watercraft SMC Hull Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipFiller it's very important to put a coarse sand scratch into the surface. Inside the v-groove. AndMoreFiller it's very important to put a coarse sand scratch into the surface. Inside the v-groove. And feather it back onto the painted surface.

How do you fix a hole in a Seadoo hull?

9:1510:27Repairing a Sea-Doo Polytec Hull - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe will melt the sandpaper fuzz off the surface with a propane torch. Keep the flame moving rapidlyMoreWe will melt the sandpaper fuzz off the surface with a propane torch. Keep the flame moving rapidly you don't want to overheat any certain area you just want to melt the fuzz created by the sandpaper.

How do you repair a deep scratch on a jet ski?

0:243:01How to fix large chips on Jet Skis - YouTubeYouTubeStart of suggested clipEnd of suggested clipSecond chip fix into the cavity. For deeper cavities several layers can be applied until fill. AllowMoreSecond chip fix into the cavity. For deeper cavities several layers can be applied until fill. Allow two hours drying time in between each layer use the leveling end of the tube to help apply nine.

How do you repair fiberglass hull damage?

0:5624:55HOW TO REPAIR FIBERGLASS DAMAGE WITH LIMITED ACCESS!YouTubeStart of suggested clipEnd of suggested clipEspecially when it's below the water line the ideal way or the the recommended way of repairing thatMoreEspecially when it's below the water line the ideal way or the the recommended way of repairing that is to basically do that repair on both sides of the laminate.

How much does it cost to repair fiberglass on a jet ski?

Fiberglass and Gelcoat repairs, which are the most common, can cost around $400. Furthermore, the higher the quality of repair materials, the higher the total cost of repair.

What is the hull of a Sea Doo made of?

The hulls of Sea-Doos are made of Polytec or with a fiberglass-based technology (CM TEC) depending on the model. The Polytec hulls debuted on the popular Spark series. Since then, more and more Sea-Doo hulls are made of this unique material.

How do you repair fiberglass?

Here's how.Drill a tiny hole at each end of the crack. This will stop the crack from extending any further.Examine the crack. ... Wipe the crack with a dry rag to make sure it's clean and dry. ... Fill the crack with a fair amount of fiberglass epoxy resin, using a plastic applicator. ... Let the epoxy dry for a day.

How do you protect a jet ski hull?

3:285:12The Best Tips to Protect Yamaha Hulls: WCJ Quick Topic - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut i strongly work or i strongly suggest clear coat way with a flex additive clear automotive clearMoreBut i strongly work or i strongly suggest clear coat way with a flex additive clear automotive clear coat with a flex additive. And that's like a 35 45 additive from any paint supply.

How do you get scratch out of a jetski?

The Steps to Repairing a Jet Ski Hull ScratchDiagnose. how deep the problem truly is. . ... Clean! Clean the area of debris. Even if you don't think your jet ski is particularly. ... Sand down. the area. . ... Replace. the gel coat. ... Once the. gel coat has cured to consistency, apply a layer of.

How do you fix a chip in a gelcoat?

2:265:22How To Repair Boat Gelcoat [MATERIALS LIST ] | BoatUSYouTubeStart of suggested clipEnd of suggested clipI thoroughly mix the Jocko and the catalyst together. And all I'm going to do is use one mixingMoreI thoroughly mix the Jocko and the catalyst together. And all I'm going to do is use one mixing stick. And drop it into the crack. And just tap it to make sure that there's no trapped air bubbles.

How do you remove scratches from a Seadoo?

0:063:16Seadoo Hull Repair - How to Repair Scuff Marks - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow what we do is we take it out firstly we use a thousand correction 2000 and 2500 sandpaper theMoreNow what we do is we take it out firstly we use a thousand correction 2000 and 2500 sandpaper the whit sandpaper. And we lightly go over that.

How do you repair a broken hull?

2:0315:14Fiberglass Hull Repair how to easily fix a thru hull hole - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe next step is just going to be to clean the entire area with acetone just put it on a cloth wipeMoreThe next step is just going to be to clean the entire area with acetone just put it on a cloth wipe it all down. And we're going to build up the fiberglass. In layers. So it's going to fill that void.

How do you protect a jet ski hull?

3:285:12The Best Tips to Protect Yamaha Hulls: WCJ Quick Topic - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut i strongly work or i strongly suggest clear coat way with a flex additive clear automotive clearMoreBut i strongly work or i strongly suggest clear coat way with a flex additive clear automotive clear coat with a flex additive. And that's like a 35 45 additive from any paint supply.

Can I use Bondo on a jet ski?

bondo is 100% fine to use on a ski for chips and filling small dimples...

How do you paint a jet ski hull?

Here are Neil's key steps and tips on how to paint a jet ski.Step 1: Remove the stickers. ... Step 2: Take off your accessories. ... Step 3: Clean the ski. ... Step 4: Reinforce the hull (optional) ... Step 5: Sand and prime. ... Step 6: Apply a guide coat and sand. ... Step 7: Apply your base color. ... Step 8: Tape your lines.More items...•

How to fix a 9 second chip?

If a rich, glossy finish is desired, apply a top-coat of Hairline fix over the 9 Second Chip Fix repair. Use the the scraper end of the tube to spread the Hairline Fix. For inverted or upside down areas, a 50mm foam roller and hairdryer may be helpful. In this instance, squirt the Hairline Fix on to the foam roller and begin to roll over the area. Whilst doing this, simultaneously blow warm air from a hairdryer to prevent dripping and help the cure process.

What color is MagicEzy 9 second chip fix?

MagicEzy 9 Second Chip Fix Midnight color (black), being a filler, cures to a matte finish, which can appear dark grey. If a rich black, glossy finish is required, then a top-coat of MagicEzy Hairline Fix (Midnight) is also required over the 9 Second Chip Fix repair.

How long to let MagicEzy stand?

Clean the scraper with a tissue and trim any excess MagicEzy using the scraper again. Set with a hair dryer for 2 minutes and let stand for approximately 2 hours. If required, apply a second layer of 9 Second Chip Fix.

How long to let Mega Fusion stand?

Set with a hair dryer for 2 minutes and let stand for approximately 2 hours.

How long to wait to reapply a coat of sand?

If more coats are required, wait at least 2 hours before reapplying. If temperatures are expected to drop below 20C / 70F, blow a warm hairdryer over the completed repair for about 2 minutes.

What is MagicEzy?

About MagicEzy. MagicEzy is unique, because it is a one-part, pre-colored system that is ready to use. This means no mixing or painting is needed and repairs can be performed in a matter of seconds. MagicEzy products have been developed using the latest nano technology, which provides ultra-strong adhesion.

Can you scrape a jet ski hull?

Here is a handy guide to help jet ski owners easily perform DIY repairs. Even the most cautious rider can easily scrape or chip the hull or may even notice stress cracks beginning to form in the high impact areas.