- Examine the insert to determine the location of all the rust. ...
- Turn off the gas to the fireplace. Remove the logs, lava rocks and any other pieces inside the fireplace.
- Recruit a friend to help you pull out the insert. Put drop cloths on the hearth and floor, then ease the insert straight out of the fireplace hole.
- Mix equal parts of water and baking soda in a bowl until it becomes a paste. ...
- Pour some distilled white vinegar in a bowl and dampen a cloth in the vinegar. ...
- Sand the metal with medium-grit sandpaper to remove any remaining rust and help the paint adhere.
- Paint the metal insert with a heat-resistant primer; it should be rated to at least 1,200 degrees Fahrenheit.
- Paint the insert with a heat-resistant paint rated to use on fireplaces. Let it dry, then add a second coat.
- Replace the insert, if you've removed it, once the second coat of paint dries. Slide it back into place, then reattach the screws or bolts inside.
How to replace fireplace insert?
How to Remove a Gas Fireplace Insert:
- Step One – Turn off the gas supply to the fireplace by turning the knob on the valve to “off.”
- Step Two – Disconnect the natural gas line from the fireplace insert by unscrewing the connector.
- Step Three – Remove the screws that hold the fireplace insert in place and pull it out of the fireplace.
How to tile around an existing fireplace insert?
Installing the Tile
- Remove the fireplace mantel, if possible, or apply a piece of 2-inch painter's tape along the entire inside edge of the mantel.
- Mix a batch of the thinset mix with latex additive with the amount of water suggested on the manufacturer's instructions.
- Fill and smooth the surface of the area to be tiled with a layer of thinset. ...
What is the average cost to repair a fireplace?
You need a professional to conduct the repairs when damage occurs to yours. The national cost average to repair a fireplace is between $200 and $1,000. Most homeowners pay around $600 to repoint a damaged section of a brick fireplace. Costs can be much higher or lower, depending on the problem and the amount of work required to fix it.
How to change a fireplace to gas insert?
- The first and most critical step is to shut off the valve or pilot light to the gas fireplace before using the highly flammable spray paint. ...
- Second, if there is a glass panel on the fireplace, remove it. ...
- The third step is to use painters tape and construction paper to protect the area around the fireplace that isn’t being painted.
Can a cracked firebox be repaired?
Repairing Firebox Cracks Depending on the damage, a professional chimney repair contractor may fill in the gaps with refractory caulk to seal them. Some repairs require tuckpointing or replacing loose bricks, which technicians with the training and experience should handle to do these repairs accurately.
How do you fix a fire insert?
Fireplace Insert FixStep 1: This Is Unsafe! Check out your fireplace. ... Step 2: Tools Needed. All you need is: ... Step 3: Cleaning. Clean the inside of the walls with soap and water and a big sponge. ... Step 4: Add Caulk. ... Step 5: Smooth Caulk. ... Step 6: Repeat. ... Step 7: Dry Time. ... Step 8: Curing.
Can you repair the inside of a fireplace?
Refractory caulk, also known as fireplace mortar, is suitable for minor repairs only. If your fireplace has broken or crumbling bricks, large gaps in the mortar, or missing mortar, have a professional mason or fireplace contractor inspect it.
How do you restore a fireplace insert?
0:159:27Restoring Wood-burning Stove Glass and Fireplace Insert ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to start by using hydrochloric acid to dissolve away the potassium. And the calciumMoreSo we're going to start by using hydrochloric acid to dissolve away the potassium. And the calcium deposits that are on the back of the glass. That's going to help a lot.
How much does it cost to repair a firebox?
Fixing a firebox costs $160 to $750. A stone firebox that needs rebuilding can cost upwards of $1,500 or $2,500.
How do you repair firebox mortar?
1:021:49Repairing Fireplace Mortar - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd work that mortar into the joint there. And smooth it out. And then you can always come back withMoreAnd work that mortar into the joint there. And smooth it out. And then you can always come back with a wet rag. And kind of smooth out the edges if you need to make a nice little mortar joint.
How do you replace a fireplace firebox?
0:4610:05Firebox Refractory Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen we're going to go ahead and cut the new panel to size we're going to install the new panel. AndMoreThen we're going to go ahead and cut the new panel to size we're going to install the new panel. And back and then we're going to reinstall the sides.
What can I use to fix a crack in my fireplace?
0:093:07How To Fix Cracked Mortar or Concrete in a Fireplace with Mor-flexxYouTubeStart of suggested clipEnd of suggested clipThis product is called more flex. This product is from a company called sashko. And it's a water-MoreThis product is called more flex. This product is from a company called sashko. And it's a water-based sealant that is sand filled.
How do you replace fireplace wall panels?
1:593:50How to install prefab fireplace panels - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the top bracket or cowling has been removed using a flat bar or flat screwdriver at the base ofMoreOnce the top bracket or cowling has been removed using a flat bar or flat screwdriver at the base of panel as leverage is lifted up out of place.
What is fire cement?
Fire Cement is a ready-to-use putty which is heat resistant up to 1250oc. There are a number of manufacturers and brands and it's available in different sizes in both black and cream. The cement can be used to seal joints in wood stoves, especially around the area where the flue rises out of the top of the stove.
How do you restore a wood burning fireplace?
0:365:39How to Restore a WOOD STOVE the EASY WAY - Like New in MinutesYouTubeStart of suggested clipEnd of suggested clipAnd you want to restore. It you can still do the exact. Same thing just hold the hose of the vacuumMoreAnd you want to restore. It you can still do the exact. Same thing just hold the hose of the vacuum cleaner near the pad while you're working. And all that dust should get sucked into the machine.
How do you fix rust on a fireplace?
Pour some distilled white vinegar in a bowl and dampen a cloth in the vinegar. Scrub the rusty areas with the cloth, then dip a steel wool pad in the vinegar and scrub them again. Alternate the cloth with the steel wool until the rust is gone.
How do you repair a metal firebox?
0:243:21how to fix firebox crack, cracked fireplace, fireplace repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipStore just a heads up all right so we've got this vacuumed out but it says that we need to wipe itMoreStore just a heads up all right so we've got this vacuumed out but it says that we need to wipe it with a wet sponge. So we're just gonna kind of get all the dust off of it.
How do I fix my electric fireplace?
Check the fireplace for any faulty wiring. A tightly bent or over-stretched power cord may be causing the problem. Check your fuse box or breaker for any switches that have tripped. Inspect the fuse on the electric fireplace and replace if necessary.
How do you fix a refractory fireplace panel?
1:334:36DIY Fireplace Panel Cracks repair of Firebrick Refractory Panel - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you can cut it so you have to find a special separate knife to cut the tip off with pleaseMoreAnd then you can cut it so you have to find a special separate knife to cut the tip off with please load them up. And let's get started look at the size of these holes.
How do you replace a brick fireplace liner?
0:192:44Renegade Brick Liner Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep 1 install the two floor pieces in the slot at the front of the fireplace. Place the short pieceMoreStep 1 install the two floor pieces in the slot at the front of the fireplace. Place the short piece to the left and the longer piece to the right.
Why do chimney sweeps inspect fireplaces?
A chimney sweep inspect your fireplace and chimney so that breaches in the safety of the unit are identified and repaired. That is the main purpose of the inspection. However, a professional is not always needed to know that the firebox is beyond simple repair. If you notice that the bricks in the firebox are crumbling and you see ...
What are the benefits of a fireplace insert?
Not only will you achieve a new look with the fireplace insert, but you will also gain practical benefits such as: A fireplace insert will allow the heat to stay inside your home rather than going up the chimney.
Can you use a fireplace without a sound box?
You may be informed one day that you will have to repair your firebox. A professional chimney sweep will tell you how unsafe it is to use a fireplace without a sound firebox. You will have to take immediate action. Although this might seem like bad news, it has a good side: repairing your firebox is a great opportunity to update your fireplace’s ...
Is a fireplace insert more expensive than a fireplace?
A fireplace insert is way less expensive than a fireplace repair. A fireplace insert burns more efficiently than the traditional fireplace. A fireplace insert will allow the heat to stay inside your home rather than going up the chimney. Since your fireplace will add heat, then your heating bills will be reduced.
Can you switch from tile to brick?
You can switch from tiles to bricks, or vice versa. Tiles come in many different colors and patterns, and they are easy to install. Achieving complete fireplace revitalization can be accomplished through changing the outer hearth.
Can you replace a fireplace with a floor to ceiling look?
If you think that your fireplace looks horribly outdated, don’t worry, you don’t have to be stuck with it . It is so easy to replace the entire floor to ceiling look of the fireplace. A simple change in the design can make your fireplace a centerpiece in your home. You will soon take great delight in your fireplace.
Is Your Electric Fireplace Light Not Working?
If you just found out that your electric fireplace just stopped working, that isn’t a nice feeling at all. However, most electric fireplace faults can be fixed. So, what do you do when this happens?
What Type of Electric Fireplace Do You Have?
The type of electric fireplace you have determines how a problem is tackled or fixed.
Troubleshooting Your Electric Fireplace
Before it’s determined that an electric fireplace needs repairs, some troubleshooting will have to be done to get to the root cause (s) of seeming malfunction. Many areas need to be looked at.
Preferred Fuel Type
Fuel preference is an easier decision to make based on the fact that you’re buying a new insert to take the place of the old. Part of the reason why an insert needs to be replaced is that it’s old and no longer burns fuel efficiently.
Fireplace Insert Replacement Cost
To replace a fireplace insert, you’ll need to figure out how much a new insert will cost.
Can I Perform the Replacement Task Myself?
Replacing a fireplace insert will require an understanding of its basic operations. Technically inclined persons will consider going ahead with the replacement process. For others, this might be a tall order.
Turn off Utilities
What actions you take during replacement is mostly determined by the fireplace fuel type. For gas and electric fireplace inserts, all utility connections must be turned off.
Remove Fireplace Doors
With utilities switched off, the next step to take is to remove the fireplace doors. These doors could be held in place by screws. Using a screw, remove the doors by unscrewing all points holding the hinges.
Unhook All Connections
With the fireplace doors successfully removed, remove all connections attached to the old fireplace insert. These could include electric cables (for electric fireplace inserts) and gas attachments.
How to tell if a metal insert is rusted?
Examine the insert to determine the location of all the rust. If rust is only visible in small areas of the front section of metal, it likely means that's the only place that's rusted. If the rust extends around the corner past your line of vision or if you see it inside the insert, you must remove the entire insert.
How to get rust off of steel wool?
Pour some distilled white vinegar in a bowl and dampen a cloth in the vinegar. Scrub the rusty areas with the cloth, then dip a steel wool pad in the vinegar and scrub them again. Alternate the cloth with the steel wool until the rust is gone.
What does rust on fireplace inserts mean?
Rust that's on the outer edges of the insert is easy to remove to help you restore the look of the insert.