Repairing Joystick/Thumbpad on Gamecube Controller
- Clean the Thumbpad and Everything Else. Like paints and glues, you're gonna want to clean the surface that you're gonna be coating. ...
- Prepping the Drying Rack. You're gonna need to have a place where you can let the Plasti-Dip dry, if you already have a place in mind, just lay ...
- Prepping the Work Area. The joystick won't reach far enough into the Plast-Dip container to be submerged, so you're gonna need to fill up another container.
- Dip It... CAREFULLY! Dip the top of the joystick SLOWLY and CAREFULLY into the Plasti Dip and do not try to take a picture with one hand while ...
- Let It Dry. The instructions on the Plasti Dip recommend that you let it dry for at least 30 min between coats and 4 hours after the last ...
- Add More Coats. I only did 2 coats, although I'd like to add a couple more. ...
- Emergency Cleanup! You'll want to clean up the bulk of the Plasti Dip first with some paper towels. ...
- You're Done! I skimmed any solid bits or layers of the Plasti Dip out of the dipping tray and poured the rest back into the original container.
- Update! I put on a couple more coats. Just the 2 coats wasn't much and it started wearing away after a while, although it's not too bad.
Full Answer
How does the GameCube controller work?
The controller also features a built in motor to provide "haptic feedback", or rumbling, while playing games. A Nintendo GameCube controller is fairly easy to identify. If you flip over the controller so the buttons are facing down, you can find "Nintendo GameCube Controller DOL-003" engraved on the left side behind the C-Stick.
Can the GameCube be repaired?
The GameCube is Nintendo's fourth console gaming system. Repair is simple and requires only common tools. Join over 20,000 fixers in promising to fix more and buy less. Gamecube won't respond to controller input.
When did the Nintendo GameCube controller come out?
The Nintendo GameCube Controller, or DOL-003, was originally released in 2001, bundled with the Nintendo GameCube. Because of its compatibility with the Nintendo GameCube, the Nintendo Wii, and the Wii U (with a special attachment), it still is widely used as of 2013.
Does the GameCube have a power cord on the back?
The back has a variety of cable ports, including the power and video cable ports. The GameCube also sports a handle for easy transportation. On November 19, 2006, Nintendo released its newest console, the Nintendo Wii, which can also run GameCube games. Your right to repair is under attack!
How do I fix my GameCube Controller?
What to doEnsure your console has the latest system update. ... If you are using a Nintendo Switch dock with LAN port, update the firmware for the dock.Unplug the GameCube Controller and GameCube Controller Adapter from the Nintendo Switch dock, then plug them back in. ... Perform a Button Test for the GameCube Controller.More items...
Can you fix a GameCube Controller joystick?
A tight analog stick is absolutely necessary to perform well, but if yours is loose, it's going to be pretty hard to fix. You'll have to replace these things on the controller, and to do that, you'll need a solder, a solder sucker, and a soldering iron.
How do you fix a GameCube Controller drift?
0:000:22How to EASILY fix a drifting Gamecube controller - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's a real easy fix if you've got drift in your controller. Like this you're gonna press x and yMoreThere's a real easy fix if you've got drift in your controller. Like this you're gonna press x and y and start and hold it for three seconds there it goes the drift. Is gone.
Why is my GameCube Controller not working on GameCube?
The first thing you should do is turn your gamecube off and back on again. If the problem persists, the second step is to check if another controller works by plugging it in in place of the original. This will determine whether or not it is your controller. If that controller also doesn't work, try a different port.
How do you open a Gamecube controller?
1:3110:54Common Mistakes: Opening a Gamecube Controller - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's important to know that all the screws on the back are the same size and the tool that you'll beMoreIt's important to know that all the screws on the back are the same size and the tool that you'll be using to open all of them is your Tri wing screwdriver.
Can you calibrate a Gamecube controller?
Holding down X, Y and start/pause for three seconds at any time will recalibrate the controller. Unplugging and reconnecting the controller, and in the case of the wireless WaveBird controller, turning the controller off and back on, will also force a recalibration.
Do GameCube controllers get stick drift?
Description: The GameCube Controller can register correctly on Nintendo Switch, but one or both control sticks are not responding correctly, or responding at all. The characters appear to be drifting, lagging, or moving on their own while using the GameCube Controller.
How do I fix my mushy GameCube buttons?
3:027:28How To Fix Your Mushy GameCube Controller Buttons... (Easy Tutorial)YouTubeStart of suggested clipEnd of suggested clipLet's do the or we did the left one let's do the middle one. Now fits in like. So do the d-pad. ThatMoreLet's do the or we did the left one let's do the middle one. Now fits in like. So do the d-pad. That one fits in nicely. And we got a couple more buttons. And these are for the triggers. Now.
How do you reset a potentiometer?
You can't physically reset the pot in software but you can use the limit switch to learn a “home” position and thereafter subtract home from the current reading to derive an absolute position. If the pot will rollover (from max R to 0 and back) things get a little tricker.
Why did my GameCube controller stop working?
If the issue persists, try the following: Use a different port on the GameCube Controller Adapter. If available, use a different GameCube Controller. Verify if a different supported device, such as a Pro Controller or a Joy-Con Charging Grip, registers correctly while connected to the USB ports on the dock.
How do you reset a GameCube controller?
Recalibrate the Controller in one of the following ways:Push RESET (or turn the system OFF and then ON) while making sure to not touch the control stick. ... Press the X, Y, and Start/Pause buttons simultaneously for three seconds during game play, making sure to not touch the control stick.More items...
Why does my GameCube controller keep disconnecting?
Check Contact Of The port The port contact where the controller goes may be dirty and need cleaning to make contact fully. Rumble should work after that if no other controller works with rumble in the same slot.
How do you fix a loose Gamecube stick?
2:5816:17How To Fix a Wobbly/Loose GameCube Controller StickYouTubeStart of suggested clipEnd of suggested clipSo what you want to do is put in your flat head and pry it up same thing off the other. AndMoreSo what you want to do is put in your flat head and pry it up same thing off the other. And eventually it'll just pop out. Like. So there you go.
How do I get rid of my drift Nintendo switch controller?
9 Ways to Fix Joy-Con Drift on Your Nintendo SwitchReset Any Button Remapping. ... Check Your Controllers Are Connected Correctly. ... Update Your Switch System. ... Update Your Joy-Con Firmware. ... Recalibrate Your Control Sticks. ... Check for Game Software Update. ... Remove Any Skins or Covers. ... Clean the Joy-Con Control Sticks.More items...•
How do you mod a GameCube Controller?
1:169:14Restoring and Modding a Gamecube Controller + Giveaway! Get ready ...YouTubeStart of suggested clipEnd of suggested clipBut they are definitely more stiff compared to the OEM stick boxes that would have come with a gameMoreBut they are definitely more stiff compared to the OEM stick boxes that would have come with a game controller. Soldering the new joystick on is easy-peasy. Just use a little bit of flux.
What screwdriver Do you need to open a GameCube Controller?
Tools Featured in this TeardownPhillips #0 Screwdriver.$1.99.Flathead 3/32" or 2.5 mm Screwdriver.Y1 Tri-point Screwdriver.
Step 1: Clean the Thumbpad and Everything Else
Like paints and glues, you're gonna want to clean the surface that you're gonna be coating. While you're at it you might as well clean the rest of the controller. Use cotton swabs dipped in alcohol to scrub up any stains and the thumbpad area.
Step 2: Prepping the Drying Rack
You're gonna need to have a place where you can let the Plasti-Dip dry, if you already have a place in mind, just lay some paper towels under it and disregard this step. I poked 4 holes into a cardboard box that my TV came in, threaded the aluminum wire through and tied it together on one side.
Step 3: Prepping the Work Area
The joystick won't reach far enough into the Plast-Dip container to be submerged, so you're gonna need to fill up another container. Preferably something shallow since you don't need to use a lot, just maybe a quarter of an inch deep, but the important thing is to fill up your container as close to the rim as you can.
Step 4: Dip It... CAREFULLY!
Dip the top of the joystick SLOWLY and CAREFULLY into the Plasti Dip and do not try to take a picture with one hand while you dip with the other or you will dip it in too far and cover the entire area with Plasti Dip, which will probably require that you take the controller apart to clean up. The instructions on the Plasti Dip suggest that you dip at a rate of 1" every 5 sec.
Step 5: Let It Dry
The instructions on the Plasti Dip recommend that you let it dry for at least 30 min between coats and 4 hours after the last coat before use. The rubber should shrink as it dries, so if it looks like it has a weird bulge, just let it dry for the full 4 hours and it should go away.
Step 6: Add More Coats
I only did 2 coats, although I'd like to add a couple more.
Step 7: Emergency Cleanup!
You'll want to clean up the bulk of the Plasti Dip first with some paper towels.
Why do buttons fall out?
Some of the buttons may fall out if they are knocked around.
Can you grab a rumble motor?
Do not grab the rumble motor to lift the circuit board as shown in the picture. It will in many cases just remove the rumble motor. Instead, grab the edges of the board.
What is the code for the Nintendo GameCube?
There are 2 main revisions of Nintendo GameCube, under the code name DOL-001 and DOL-101.
Which Nintendo consoles can run GameCube games?
On November 19, 2006, Nintendo released its newest console, the Nintendo Wii, which can also run GameCube games.
How many memory cards does a GameCube have?
On the front it has four controller ports and two memory card slots.
How to get the controller apart?
Gently pry the two halves of the controller apart using plastic cards or tools.
What is the best tool to pry a bar down?
A flathead screwdriver may be used to gently pry the bar down. Do not bend the bar or break the plastic.
