Repairing Guides

how to repair gas dryer not heating

by Araceli Mueller Published 3 years ago Updated 2 years ago
image

Common solutions for: Dryer not heating

  1. Thermal Fuse. The thermal fuse is a safety device designed to protect the dryer from overheating. ...
  2. Gas Valve Solenoid. Gas dryers have two or more gas valve solenoid coils. ...
  3. Igniter. The igniter uses heat to ignite the gas in the burner assembly. ...
  4. Flame Sensor. On a gas dryer, the flame sensor detects the heat emitted by the flame. If the flame sensor isn’t working, the dryer won’t heat.
  5. Heating Element. The heating element warms the air before it enters the dryer drum. Over time, the heating element can burn out, causing the dryer not to heat.
  6. Heating Element Assembly. The heating element assembly warms the air before it enters the dryer drum. ...
  7. Incoming Power Problem. If your dryer is not heating, then you may have an incoming power problem. ...
  8. High Limit Thermostat. The high-limit thermostat monitors the dryer temperature and shuts off the burner if the dryer overheats.
  9. Cycling Thermostat. The cycling thermostat cycles the heat on and off to regulate the air temperature. If the cycling thermostat is defective, the dryer will not heat.
  10. Main Control Board. The main control board might be defective. However, this is rarely the case. ...
  11. Timer. If the dryer doesn’t heat, the timer might be defective. However, this is very rarely the case. ...

Full Answer

How to fix Kenmore Elite electric dryer not heating?

How to Fix It

  • When you have located the thermal fuse, remove the two wires which are attached to it.
  • With your multimeter set to measure resistance (Ω), touch the probe leads on the multimeter against the terminals on the fuse where the wires were attached.
  • If your meter gives a reading close to zero ohms (0Ω), that means that the fuse is still intact. ...

More items...

What to check when your dryer will not heat?

Why a Dryer Has Stopped Heating

  • Thermal Fuse. If your dryer is tumbling but no longer producing heat, your first suspect should be the thermal fuse.
  • Exhaust Vent. If your thermal fuse was responsible for the issue, your first course of action after replacing it should be to check your dryer vent.
  • Thermostat and Temperature Switch. ...
  • Heating Coils. ...

What causes a gas dryer to stop heating?

What Causes a Gas Dryer to Stop Heating?

  • Thermal Fuse. If the air flow in the dryer is restricted, the temperature in the heating chamber can get hot enough to blow the thermal fuse.
  • Igniter and Gas Valve Coils. The igniter is an electric conductor that works like the element in an electric heater, glowing hot enough to ignite gas when you turn on ...
  • Air Flow and Heat. ...
  • Warning. ...

What to do when gas dryer is not heating up?

Here’s how to replace the ignitor on a Whirlpool gas dryer:

  • Unplug the power from the dryer
  • Pull out the lint remover screen
  • Remove the screws around the lint screen
  • Use a putty knife to release the spring clips on the top of the dryer
  • Rotate the top up and flip it back
  • Disconnect the door switch wire
  • Remove the top, front panel screws
  • Lift the panel up and out

More items...

image

How do you fix a gas dryer that won't heat?

0:103:01Top 5 Reasons Gas Dryer Is Not Heating — Dryer TroubleshootingYouTubeStart of suggested clipEnd of suggested clipYou can use a multimeter to determine if there is a continuous electrical path present in the part.MoreYou can use a multimeter to determine if there is a continuous electrical path present in the part. If not the fuse has blown. And will need to be replaced.

Why is my gas dryer blowing cold air?

One of the most common reasons your tumble dryer decides to blow out cold air instead of hot is, rather ironically, because it has overheated. Manufacturers have a legal requirement to ensure that when your dryer gets too hot there is some form of control in place to prevent it catching fire.

How do you know if the ignitor is bad on a gas dryer?

0:062:11Dryer Won't Heat? Igniter Testing - Troubleshooting & Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can often determine that a dryer igniter has burned out by checking to see if the filament isMoreYou can often determine that a dryer igniter has burned out by checking to see if the filament is singed or cracked.

What causes a gas dryer to not heat up?

Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.

How do you fix a dryer that blows cold air?

0:121:56How to Fix a Tumble Dryer that isn't Heating - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou must ensure that the appliance is first unplugged from the mains. If your tumble dryer isn'tMoreYou must ensure that the appliance is first unplugged from the mains. If your tumble dryer isn't producing heat and it's just blown cold air it may be due to a faulty heater element.

How much does it cost to fix a gas dryer that won't heat up?

Dryer Not Heating Repair Cost Fixing a dryer that does not heat averages $100 to $350. The price for this repair depends on the problem because it could be something wrong with the heating element or with the thermostat or igniter when using a gas dryer.

How much does a gas dryer igniter cost?

Compare with similar itemsThis item Whirlpool 279311 Igniter for Dryer, WhiteWhirlpool 20-48KITRC Gas Dryer Hook-Up KitAdd to CartAdd to CartCustomer Rating4.5 out of 5 stars (1050)4.6 out of 5 stars (86)Price$2184$3995Sold ByQuickShipPartsAppliance Parts By Trible's3 more rows

Is there a thermal fuse on a gas dryer?

0:081:29How to Replace a Whirlpool Gas Dryer Thermal Fuse - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen the thermal fuse is blown in a gas dryer the burner won't ignite. You can't reset the thermalMoreWhen the thermal fuse is blown in a gas dryer the burner won't ignite. You can't reset the thermal fuse. If it's blown you have to replace it with a manufacturer-approved replacement.

Where is the igniter on a gas dryer?

0:082:49How to Replace a Whirlpool Gas Dryer Igniter - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn a gas dryer the igniter is on the side of the gas burner funnel it glows white hot during theMoreIn a gas dryer the igniter is on the side of the gas burner funnel it glows white hot during the ignition process to light the gas if the igniter doesn't glow or get hot enough to light the gas.

Is it worth replacing a heating element in a dryer?

If your dryer's heating element burns out more than once within a year or two, the thermal fuse, which is supposed to protect it, is probably defective, so it's a good idea to replace it. The temperature in the heating chamber may also be too high, and that may be caused by poor venting.

How do I reset my thermal fuse?

2:524:55Reset Dryer Thermal Fuse / Switch (Dryer won't heat fix) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you have this issue and you keep spot or you trip this you may want to try drilling this. AndMoreSo if you have this issue and you keep spot or you trip this you may want to try drilling this. And then you got a little bit of pressure. And it resets. It. So if you're testing your dryer.

How much does it cost to replace heating element in dryer?

Dryer Heating Element Cost For the cost of parts and labor, you should budget at least $170 to $280 for a new heating element. An appliance technician typically charges between $80 and $100 per hour for labor. This cost also includes a one-time service fee. Most technicians' service fees span from $50 to $80.

Why is my gas dryer not drying?

When a gas dryer tumbles but doesn’t dry, it may have one of the following problems: While that appears to be a laundry list of potential problems, the cause is most commonly attributed to restricted airflow, a bad thermostat or a bad igniter.

How to test a gas dryer igniter?

The best way to test the igniter is to watch it in action. Remove the access panel on the front of the dryer. Set the dryer to run at the highest temperature setting and start the machine.

How often should I clean a dryer lint trap?

The lint trap should be cleaned after each and every load. Once you clean the lint trap, look behind the dryer to make sure the exhaust hose is connected to the outside vent, and look for any kinks in the hose that may be obstructing the flow of the exhaust.

Where is the thermostat located on a gas dryer?

They are usually small, silver discs that can sometimes be grouped together. Depending on the model of your dryer, they can be located under the lint trap, on the blower housing or inside the vent line.

What causes a bad gas valve coil?

Bad igniter. While that appears to be a laundry list of potential problems, the cause is most commonly attributed to restricted airflow, a bad thermostat or a bad igniter.

What to do if your burner doesn't work?

While watching the burner assembly, look for the spark or glow of the igniter. If you have the spark-type and it doesn’t work, it will probably have to be serviced by a professional repairman. If it is the glow-type igniter, you can perform a test using your multi-tester.

Can a gas dryer cause poor airflow?

However, even more than an inconvenience, poor airflow through a gas dryer can be a potential safety hazard.

Why won't my dryer heat up?

A dryer that won’t heat up may have a defective cycling thermostat. This part governs the temperature of the dryer drum by opening when the drum gets hot and thus breaking the electrical flow to the heating element. Then when the drum cools, the cycling thermostat closes, power can run through it, and the heater is switched back on.

Why is my dryer not producing heat?

If your gas dryer is not producing enough heat, there may be a problem with the gas valve, which is in the gas burner system. The gas valve is designed to receive power from the circuit of the igniter and flame sensor, which will power the coils of the valve and allow the valve to open. Gas is then released into the burner, the gas ignites, ...

What to do if the igniter is not working?

If it’s the igniter that isn’t getting its cue from the sensor, unplug the dryer and use your multi-meter to check the sensor for continuity. And if the igniter’s always aglow but the gas valve won’t open, then the sensor has malfunctioning electrical contacts and needs to be replaced.

What happens if the exhaust vent on my dryer is kinked or blocked?

Need Help Finding Your Model Number? If the exhaust vent on your dryer is kinked or blocked, the hot air will be confined in the dryer and the high limit thermostat attached to the heating chamber will trip and stop the electricity from flowing to the gas valve or heating element.

What is the sensor on a dryer?

On a gas dryer, there’s a radiant sensor or flame sensor on the burner assembly, next to the igniter. This sensor detects heat, whether it comes from the burner flame or the igniter. The igniter’s heat signals the gas valve to open, and the burner flame keeps the gas valve on. A broken sensor will result in a valve that won’t open ...

How to test if a dryer is cool?

You can test your heating element with a multi-meter to see if it is the source of your dryer’s coolness. Just remember to unplug the dryer first, then find the heating element behind either the front or rear panel.

What does it mean when a dryer goes off?

Keep in mind that if this safety device has gone off, it usually means that the dryer has gone above its safe level of heat, and it would only do that if one of the other thermostats or components has failed, or the exhaust vent is restricted.

Why is my gas dryer not getting hot?

If you made it all the way though and you still haven’t found out why your gas dryer is not getting hot, you could have a defective motor centrifugal switch or a wiring failure in the heating circuit. You would need a service technician to check this out for you.

What could keep my dryer from heating up?

There are a few things that could keep your dryer from heating up. You might have a problem with the gas supply to the dryer , or problems with the flame sensor, gas valve coils, high-limit thermostat, operating thermostat, thermal cut-off fuse, thermal fuse, igniter or timer.

How to release tension on a dryer?

Push the idler pulley to the right to release tension on the drive belt. Pull the drive belt off the idler pulley and the motor pulley. Pull the drum out of the dryer and set it aside. Unplug the wire harness from the igniter. Place one meter lead on each terminal of the igniter.

How to remove the back panel of a dryer?

First, unplug the dryer. For safety, always disconnect power before checking continuity. Remove the back panel from the dryer, then remove the back of the control panel. Pull the wire harness plug with red, black and blue wires off the timer and the light blue wire from the thermal fuse.

Why does the igniter fade off?

The igniter should fade off to divert electric current through the gas valve coils to light the burner when the flame sensor detects that the igniter is hot enough. When the flame sensor opens, electric current flows through the gas valve coils and the burner ignites.

Why won't my dryer heat up?

One of the chief reasons why a dryer won’t heat up is that only one of the hot contacts of the circuit breaker is attached properly, while the other two are hanging loosely. As a result, the dryer can only get 120, not 240 volts of power — so there’s no hot air coming out of the device.

Why is there no hot air coming out of my dryer?

As a result, the dryer can only get 120, not 240 volts of power — so there’s no hot air coming out of the device. Reason #2. Heating element issues. Although it sounds fancy, the heating element is nothing but a non-conducting wire inside the dryer.

How to fix a dryer filter?

Here’s how to fix the dryer filter problem: Unplug the appliance. Remove the cover panel and use a pin or a pair of tweezers to get rid of any dust in the filter in the back of the dryer.

How to contact a dryer repair?

To hire our professional technical team for a dryer or other appliance repair, leave us a message or call 1-888-242-0777. We’ll get in touch with you right away and find out why your dryer doesn’t heat up.

What is the main control board on a dryer?

Main control board. This is one of the most important components of a dryer as it controls all cycles and circuits inside the appliance. Charring inside the control board or short-circuiting can both hinder the steady heating of the appliance.

Can a dryer not heat?

Struggling with a dryer not heating properly is a common problem. The good news is, most problems can be repaired easily — there’s no need to worry about having to purchase a new one.

Why is my dryer not heating?

Reasons Why Your Dryer Is Not Getting Hot. Dryer vent is clogged. Improper or no electric or gas supply to the dryer. Clogged lint screen. Uneven loads. Washer leaving clothes too wet. 1. Dryer vent is clogged. This is the most common cause of a dryer not heating.

What happens if your dryer vent is too low?

If there’s little airflow, your venting likely needs to be cleaned or replaced. If the temperature’s too low, there may be an operational issue with the dryer, which should be checked by an authorized service technician. 2. Improper or no electric or gas supply to the dryer.

What type of load are you drying?

What type of load are you drying? If you mixed large and small items, that might be the problem. Washing and drying similar items together is imperative to proper performance. This is especially true on an auto dry cycle. Putting things like towels and sheets together can cause the dryer to heat at a lower level and sometimes even shut off, thinking the items are dry. The smaller or lighter clothes will be dry, but the larger, heavier items will still be damp.

Does a dryer run on gas?

If only one of the lines is working, the dryer will run but not heat up. With gas, the appliance won’t heat if your gas is off. Both issues should be checked by a professional.

Do dryers dry clothes?

They’re supposed to actually dry your clothes. So when you’ve got wet clothes after running a load in the dryer, your appliance isn’t doing its job. Before you panic, though, not all dryer problems require a visit from a technician.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9