Repairing Guides

how to repair gear shifter on bike

by Prof. Karley Fahey Published 2 years ago Updated 2 years ago
image

There are two steps that you will need to take for replacing a gear shift: 1) Remove your old gear shift knob or lever 2) Disconnect the negative battery cable and remove it from its socket on the frame

Part of a video titled How To Fix Bike Not Shifting Gears - YouTube
1:10
9:15
Just hold the cable down here and just try shifting it do you feel it pull the cable down there andMoreJust hold the cable down here and just try shifting it do you feel it pull the cable down there and do you feel it releasing the cable. And. So if it's pulling holding and releasing a cable then.

Full Answer

How to replace the gear shifter on a bicycle?

How to Replace the Gear Shifter on a Bicycle

  1. Remove the grip that is on the same side of the handlebar as the shifter you are replacing. ...
  2. Shift the chain onto the smallest front or rear gears so there is a minimum of tension on the cable of the shifter you are replacing.
  3. Slide your new shifter onto the handlebar and tighten its hex bolt. ...
  4. Reinstall your brake levers if necessary. ...

How to shift gears correctly on your bicycle?

Part 2 Part 2 of 3: Shifting Basics Download Article

  1. Use your left hand to shift the front gears. Bikes with gears almost always have hand controls on the handlebars to use for shifting.
  2. Use your right hand to shift the rear gears. The rear gears have their own derailleur. ...
  3. Gear down to make your pedaling easier but less powerful. ...
  4. Gear up to make your pedaling harder but more powerful. ...

More items...

How to fix a broken gear cable on your bicycle?

Steps for Shifter Cable Replacement

  • Shift the chain onto the smallest front and rear cogs.
  • Unwrap your bar tape in order to access the shifters.
  • Clip off the end cap and remove the cable from the old housing.
  • Fully remove the old cable from the shifter.
  • Use the old housing as a guide measure, and cut the new lengths of cable housing.

More items...

How do I fix gears in a bicycle?

  • The front derailleur must be in the smallest ring or the middle ring. ...
  • Use the pedal gently to push the derailleur so that the chain comes up. ...
  • Now, start pedaling again so that the chain goes back to the smallest cog.
  • After this, you can test your gears once by using the shiftier. ...

More items...

image

Why is my shifter not working bike?

Cable tension and limit setting The most obvious and common causes for poor shifting are down to poor adjustment and the most common thing to go out of adjustment is cable tension. Indexed drivetrains rely on correct cable tension so that the shifters pull the derailleur to the intended spot.

How do you fix a shifter on a road bike?

3:256:395 Hacks For Perfect Shifting On Your Road Bike - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgainst your outer chain ring. At this point which you clamp the cable. And then when you screw theMoreAgainst your outer chain ring. At this point which you clamp the cable. And then when you screw the lower limit screw out to its correct position which is one or two mil inboard of the chain. Then.

How do you fix shifter not catching?

0:523:35How To Fix Shifter Not Catching/Clicking - Won't ShiftYouTubeStart of suggested clipEnd of suggested clipInto like a hole in the side of the shifter. It's just kind of flood the inside of it in there withMoreInto like a hole in the side of the shifter. It's just kind of flood the inside of it in there with wd-40. And then start working the mechanism.

How do I fix my front bike shifter?

1:3313:44How to Adjust a Front Derailleur - YouTubeYouTubeStart of suggested clipEnd of suggested clipListen Jen mounting bolt and move it up or down as needed keep in mind also any changes needed inMoreListen Jen mounting bolt and move it up or down as needed keep in mind also any changes needed in rotation secure the mounting bolt and inspect the cage.

How do you disassemble a bike shifter?

0:0012:17How To Disassemble/Reassemble Shimano RSX STI Shifters/Brifters ...YouTubeStart of suggested clipEnd of suggested clipOut. Like that and we might need to compress the brake lever a little bit. And there's the pin thereMoreOut. Like that and we might need to compress the brake lever a little bit. And there's the pin there put it aside and so now this will come apart. And there's no parts in here to really loose.

How do I fix my Shimano gear shifter?

0:136:09Your Shimano shifter needs cleaning, not an adjustment of the derailleur ...YouTubeStart of suggested clipEnd of suggested clipIn there simple wd-40 stuff goes a long way so this is great for breaking.MoreIn there simple wd-40 stuff goes a long way so this is great for breaking.

How do you fix a Shimano bike shifter?

0:253:43How to fix a shimano shifter that won't shift - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's easiest if you rotate the shifter. Back it's loosen up the little five millimeter bolt thatMoreIt's easiest if you rotate the shifter. Back it's loosen up the little five millimeter bolt that secures it to the bars. And remove the little Phillips. Screw. There you can remove the little cover.

Why is my front derailleur not shifting?

Common Front Derailleur Problems. Front derailleurs may cause sluggish or inaccurate shifting because (A) the derailleur body is not positioned properly, (B) the derailleur limit screws are not adjusted correctly, (C) the mechanism is dirty or (D) the cable is damaged or improperly tensioned.

Why are my bike gears slipping?

When your bike chain skips between gears while you're riding, or shifts twice instead of once when you try to change gears, the most common culprit is a loose cable. Your bike cables naturally stretch over time.

Which way tightens a barrel adjuster?

Clockwise "tightens" the barrel adjuster, like a screw, so it threads INTO the shifter and shortens the cable path, loosening the cable. When you install new cables, make sure your barrel adjusters are fully tightened so you have maximum adjustment as your cables lengthen.

What would cause a transmission to not go into gear?

Transmission won't engage or stay in gear If when you put your vehicle into gear and it won't move, this may be a problem with low transmission fluid due to a leak, the shifter, shifter cable, or it could even be a problem in the valve body of your automatic transmission.

Why is my gear shifter stuck?

Common causes are: You're parked on a hill: When you park on a steep incline, pressure on the praw can cause it to get jammed into the parking gear. In this case, you have to relieve the stress to switch gears—often by recruiting another person to help you rock the vehicle back and forth.

How do I adjust my grip shift?

0:375:16Bike Restoration: Grip Shift & Final Steps - YouTubeYouTubeStart of suggested clipEnd of suggested clipAt this shift handle for the front dérailleur will go ahead and turn the barrel gesture all the wayMoreAt this shift handle for the front dérailleur will go ahead and turn the barrel gesture all the way in. And then we'll turn it out several turns shift to the smallest chainring.

How do you adjust a thumb shifter?

8:019:37microSHIFT Thumb Shifters Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the barrel adjuster counterclockwise to add tension. And clockwise to release it. If the frontMoreTurn the barrel adjuster counterclockwise to add tension. And clockwise to release it. If the front derailleur is slow to shift to a bigger chain ring add tension.

How to fix bike gears that won't shift?

How to Fix Bike Gears That Won’t Shift Step by Step. Step 1. Position your bike on a bike stand. Getting the right angle when fixing your bike gear is incredibly important as well as spinning your wheels from time to time without moving the bike.

Why won't my bike gears shift?

There are several reasons why your bike gear wheels won’t shift. It can be due to derailleur problems, cable issues, mis-adjustments, and malfunctioning chains. To understand these issues better, read through the following so you can fix gears mountain bike: 1. Derailleur problems.

What is a bike derailleur?

Bike derailleurs are responsible for shifting the bike gear and keeping the bike chain in place. There are two derailleurs present on the bike: the rear derailleur and the front derailleur. You have to identify them both and ensure that they are clean without any unnecessary components built up.

How to diagnose a bike shifting problem?

Diagnose bike gear shifting problems. To determine the shifting problem, you have to test each gear. You can use your hand to move and pedal the bike. Start with the back derailleur and pedal test each gear slowly. In this way, you can determine whether your bike won’t shift to the highest gear front.

Why are bike gears important?

Bike gears are crucial when you want to enjoy a hassle-free and smooth ride. It is equally important to understand how bike gears work, and how to fix them in case a problem arises. Fixing bike gears that won’t shift will no longer be challenging now that you have read through these detailed steps provided for you.

Why is my bike slowing down?

Misadjusting the cable or misaligning it can cause your bike to slow down. It is crucial to check the position of your cable frequently. You need to clean it regularly for optimum performance as well. If you have an old cable, and your gear won’t shift, you have to replace it.

Why do you need bike gears?

Bike gears give you a more pleasurable and enjoyable ride no matter the terrain. Gears are a crucial component of your bike. It transfers the energy you put into the pedals as an output of your wheel. It also lessens your effort to pedal when you shift to the right gear.

How do bicycle shifters work?

Usually located on the handlebars, the shifters connect to the bicycle's derailleurs via a wire cable. Pushing or pulling the shifter levers moves the cable and causes the derailleur to push the chain onto a different gear.

How to replace a shifter on a sandbox?

Step 1. Remove the grip that is on the same side of the handlebar as the shifter you are replacing. Using a butter knife, pry the grip away from the handlebar and pour water under the grip. Periodically twist the grip as you are doing this until you are able to remove it from the bar. Advertisement.

Can you lose control of a bicycle if you have loose grips?

Be sure to let your grips dry completely before riding; loose grips can cause you to lose control. If at any point you do not feel comfortable completing any of these repairs, consult with your local bicycle shop.

Why are bicycles with gears becoming so popular?

Bicycles with gears are becoming increasingly popular because they allow you to deal with multiple terrains and provide greater control over your pedaling efficiency.

Cable Issues

The main component that connects your gears with the rest of the bike is cables. The reason behind a bicycle gear shifter not working can often be down to issues with the cable. It’s important to periodically check the cables that connect your shifter to the drivetrain.

Derailleur Issues

A bike derailleur is a mechanism responsible for shifting the chain in the rear sprockets. Even though there might be several different derailleur models, the basic concept is the same. They shift the chain at the rear sprocket and help control the pedaling efficiency.

Shifter Lever Issues

You can also potentially encounter issues with the lever. This is one of the most common reasons behind Shimano gears not shifting properly. When levers are positioned on the bottom of the shifter, it’s possible for water and other materials to accumulate.

Chain Issues

Lastly, the final component that you should check is the chain. Every chain features a B-tension screw that requires adjustment to function properly. The screw controls how close the upper jockey wheel sits next to the cassette.

Conclusion

While multi-speed bicycles are definitely helping take cycling forward, they can also present some issues. Learning how to deal with these issues is a crucial aspect of improving as a cyclist.

Why bananas good for cyclists

After learning how to ride a bicycle much later than all the other kids, James Dawson hasn't looked back. The author now actively rides a bicycle as a part of the community cycling group and competes regularly in local competitions. Aside from that, he loves technology and always keeps up to date with the latest cycling tech.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9