
If your GHDs are constantly beeping and wont heat up, before you book a repair let the straighteners warm up to above 11 degrees and they should then work properly. If you are in a rush to use them then they can be placed on a radiator for a short period of time or gently heated with a hairdryer.
Full Answer
What should I do if my ghds wont heat up?
If your GHDs are constantly beeping and wont heat up, before you book a repair let the straighteners warm up to above 11 degrees and they should then work properly. If you are in a rush to use them then they can be placed on a radiator for a short period of time or gently heated with a hairdryer.
Do you get ghds sent to you for repair?
At FixMyGhds we occasionally get GHD repairs sent to us and when we test them there doesn’t appear to be a fault. We go through the ghds and test all the components thoroughly and as a last resort we will ring the customer. When we ask what the fault is they say it is a constant beeping noise and they don’t warm up.
Should I buy GHD or ghd5?
My own personal advice is if you are going to buy GHDS then go for the older model ghd5 which is not only considerably cheaper but appears to more reliable and can be repaired if they ever go faulty Why choose GHD SS5.0 Wide Plate Hair Straighteners?
Why did my GHD ceramic heater crack?
However, the edges of each of the heating elements are very close to each other and 1 area may be cooling slightly while an adjacent area is heating. Over many cycles this is likely to stress the ceramic and eventually cause it to crack. Fortunately, GHD still make the previous model GHD 5.0 which was probably the most reliable model that GHD made.

Can you fix GHD Platinum?
NOBODY CAN! GHD have made the internal parts in a totally different way to other GHD models. Components cannot be removed from the circuit inside. The GHD Platinum is notoriously unreliable – typical then that they have made it unserviceable too.
Can GHD straighteners be repaired?
Ghd Gold can be repaired by fixmyghds.com FixMyGhds.com can also repair any model of ghds if they have a button that slides. The Model number is shown usually on the top left hand corner of a sticker that is inside the arm. The models that cannot be repaired are Platinum, Eclipse, Hairdryers and curling tongs.
How do I fix my GHD Platinum flashing red?
If your product stops working and the red fault light flashes, please follow the procedure below:Switch off the unit.Unplug the unit from the plug socket.Wait for 5 seconds and then plug the unit back into the wall.Switch the unit back on.
What does a red flashing light on GHD Platinum mean?
It's normal for the straightener to flash solid red as soon as you turn the switch on. It will then beep and start flashing as soon as it's hot and this tells you it's ready to be used.
Why have my GHD straighteners stopped working?
No power to your ghds could also mean the thermal fuse has blown inside. This is designed to blow when ghds overheat. They can blow prematurely for no reason other than prolonged use. However it could have blown due to a component failure on the chipboard that requires a full chip board replacement.
How do you fix a GHD straightener that won't heat up?
If your GHDs are constantly beeping and wont heat up, before you book a repair let the straighteners warm up to above 11 degrees and they should then work properly. If you are in a rush to use them then they can be placed on a radiator for a short period of time or gently heated with a hairdryer.
Why are my GHDS beeping and flashing?
1) The irons are too cold Not a problem with the irons exactly, but if the irons are too cold when they are switched on you will get a continuous beep and flashing light and the irons will not heat up. GHD call this a feature and say it is to protect against damage occuring.
Why is my GHD unplugged flashing red?
This is called Failsafe mode. If this happens you may get a bleep and flash of red LED and nothing else. Try unplugging them from the mains for a minute or two and then plugging them back in. Failsafe mode should then be reset and the irons would function normally.
Why is my GHD Platinum beeping?
If they randomly Ghd beeping from time to time when using them then it will be a power cable problem or with the power cable connector inside. The ghds will be turning off due to a intermittent power fault. They will be losing power for a short time and then when the power connection is made again there will be a beep.
How long does GHD straightener last?
How long do ghds last? Most ghd straighteners come with a warranty of two or three years for peace of mind but many users claim that their styler has lasted upwards of five years. The trick is to take good care of the styler, cleaning them after use (once cooled) and storing them in a heat-resistant bag.
How long does GHD warranty last?
2 years warranty: straighteners (including ghd platinum), curling tools, hot brushes, helios hair dryer (excluding professional use) and flight travel hair dryers. 1 year warranty on ghd air hair dryer and professional use ghd helios.
How do I get my GHDS out of shiver mode?
To get them out of Shiver Mode, switch off and unplug. Hold the plates in your hands for a few minutes to warm them up, then try again. During the colder months store your ghd's wrapped in a towel.
Do GHD straighteners have a lifetime guarantee?
2 years warranty: straighteners (including ghd platinum), curling tools, hot brushes, helios hair dryer (excluding professional use) and flight travel hair dryers. 1 year warranty on ghd air hair dryer and professional use ghd helios. 6 month warranty on ghd hair brushes.
How long should GHD straighteners last?
2-3 years'Straightening irons normally need to be replaced every 2-3 years,' Jackie concludes. 'Store yours in a heatproof zip-up case for maximum use. '
Why do hair straighteners stop working?
Check the cord for any frayed or exposed wires. If that is fine, it could either be a faulty on/off switch or a blown fuse. See our troubleshooting guide here for more information. if your flat iron is not working then make sure it's plugged in or you can replace it with a new one.
How do you fix a straightener plate?
0:499:29How too repair loose flat iron plate. - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut you mix equal parts of this.MoreBut you mix equal parts of this.
FILL IN THE ONLINE RETURN FORM
Please fill in the returns form below. This will help you to provide us with the details that will make your return process as fast and simple as possible.
PRODUCING THE RETURN FORM
You will be emailed and given the option to print your returns form, we require you include this with your styler/product. You will also receive a postage paid label which you will need attach to the outer package.
PREPARING THE PACKAGE
Place your styler/product into secure packaging, the original packaging and its contents are not needed.
SENDING THE PACKAGE
We highly recommend that you use a registered insured delivery service. This will allow you to keep track of your package.
Will I have to pay for my styler to be returned?
Within the warranty period we will cover any return charges to UK addresses. Regrettably we are unable to cover any postage costs outside the UK.
Why do ceramic heaters crack?
With time and heat cycles the rubber supports appear to deteriorate and stick to the plate and cause problems as the ceramic heater heats and cools. Secondly and probably a more contributory factor is the “Tri Zone Technology”. As explained earlier each heater is divided into 3 zones which heat and cool at different times in theory to keep the plates a constant temperature along the length of the plate. However, the edges of each of the heating elements are very close to each other and 1 area may be cooling slightly while an adjacent area is heating. Over many cycles this is likely to stress the ceramic and eventually cause it to crack.
Is GHD still making the GHD 5.0?
Fortunately, GHD still make the previous model GH D 5.0 which was probably the most reliable model that GHD made. Eclipse and Platinum appear to be a step backwards and it is important that potential customers read the reviews online to get an idea for themselves as to whether the Eclipse and Platinum are worth the money for a product that may not be as reliable as the old models and may not last as long.
Does GHD have a heater?
‘tri zone technology’. In Ghd5.0 and older there is one heater in each arm. The heater in the non-switch arm has an electronic component (thermistor) bonded to it. The Thermistor senses the temperature and sends a signal to the electronics to control both heaters and so the temperature in both plates.
What is shiver mode on a GHD?
Shiver Mode is a feature that GHD straighteners have built in in all models after the GHD 3.1b. (so GHD4.0 to 4.2b, 5.0 ect). It is designed so that when the temperature is below about 11 degrees C the ghds will not power the heater plates up and the GHD,s will just make a constant beeping noise.
Can a GHD be left in a cold car?
Also if you have been travelling and the ghd’s have been left in a cold car for example they may go into Shiver Mode when you first take them into the house. If your GHDs are constantly beeping and wont heat up, before you book a repair let the straighteners warm up to above 11 degrees and they should then work properly.
