Repairing Guides

how to repair graco airless pump

by Joanny Kilback DVM Published 3 years ago Updated 2 years ago
image

Remove defective pump (previously remove anti-static cable – only Graco UltraMax) Insert replacement pump – Leave plastic protection on pump (connect anti-static cable to pumpGraco UltraMax only) Position pump and remove plastic guard

Full Answer

How do you repack a Graco airless sprayer?

1:197:28Graco QuikPak - How to Repack Your Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd remove the packing nut packing a ring and dust shield unscrew the intake valve from the cylinderMoreAnd remove the packing nut packing a ring and dust shield unscrew the intake valve from the cylinder. Disassemble the intake valve remove the seat intake ball ball cage and white o ring clean.

Why is my airless sprayer not building pressure?

If this is the issue you experience the most likely cause is that the transducer is worn out. The transducer signals to the airless pump that pressure is needed and signals to run the pump to build pressure. Failure to build pressure often indicates that you need to replace the transducer.

Why is my Graco sprayer not working?

0:082:47Basic Troubleshooting With Your Graco Paint Sprayer - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the suction tube is immersed into the paint. Also the inlet valve check ball may be stuckMoreMake sure the suction tube is immersed into the paint. Also the inlet valve check ball may be stuck remove. The suction tube.

How do you fix an airless sprayer that is not priming?

4:546:54How To Fix An Airless Sprayer That Is Not Priming. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes the piece of debris. That's up inside there that won't pass through that ball is veryMoreSometimes the piece of debris. That's up inside there that won't pass through that ball is very small and sometimes just a little bit of a tap will get it to flow through.

How do you prime a sprayer pump?

0:492:20Priming the Pump on Your Chapin ATV Sprayer - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition take the shut off and rest the wand inside the tank with your sprayer. Connected. Turn itMorePosition take the shut off and rest the wand inside the tank with your sprayer. Connected. Turn it on. Hold the end of a garden hose to the end of the inlet hose where the filter.

How do you open a stuck pump sprayer?

Push the pump handle all the way down and turn counter clockwise into the locked position. Continue to turn the pump handle counter clockwise until the entire lid starts to turn and unscrew. This can be difficult sometimes if the lids are put on very tight.

How do you fix a spray bottle pump mechanism?

0:001:06quick fix SPRAY BOTTLE (nozzle sprayer, trigger spray, mister spray)YouTubeStart of suggested clipEnd of suggested clipNow when we apply this silicone grease you'll see how fast this works the plunger almost comes backMoreNow when we apply this silicone grease you'll see how fast this works the plunger almost comes back immediately. Just keep working in the grease. And you'll have your spray bottle.

How do you prime a Graco pump?

0:290:58What to do if your Graco Magnum pump is not priming - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd place the eraser end of a pencil into the inlet section of the pump to dislodge the inlet ball.MoreAnd place the eraser end of a pencil into the inlet section of the pump to dislodge the inlet ball. This will allow the pump to primed properly.

Why is my spray gun not spraying?

If your paint gun is not spraying paint at all, it's most likely due to a clog either in the air vent hole or the hose. Clean any dried paint with a toothpick, and use a cleaning solvent to clear any remaining gunk. If you've cleaned your paint gun and find that it still isn't spraying, take a look at the air supply.

How do you fix an airless paint sprayer?

0:064:59Fixing An Airless Paint Sprayer - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd stuff and it'll release or you'll get a piece of grass or a little rock. Or something that willMoreAnd stuff and it'll release or you'll get a piece of grass or a little rock. Or something that will get stuck in this ball. It's really easy to fix all you got to do is release this nut on the bottom.

How does an airless paint sprayer pump work?

An airless sprayer works by pumping paint at a very high pressure, up to 3,000 psi, through a hose and out a tiny hole in the spray gun tip. The tip is designed to break up the paint evenly into a fan-shaped spray pattern of tiny droplets.

Why is my electric paint sprayer not working?

0:581:50Wagner Tips & Troubleshooting: Sprayer Won't Spray - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe seal is in the wrong way or the tooth is clogged if flex your sprayer will not operate correctlyMoreThe seal is in the wrong way or the tooth is clogged if flex your sprayer will not operate correctly a second.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9