_WW_1.gif)
How to Fix a Hayward Navigator Pool Vacuum That Is Not Moving
- Determining What Needs to Be Replaced. If your navigator seems to spin around in circles without really going anywhere, or if it doesn’t really move at all, or if ...
- Checking the “A-Frame”. The A-Frame is inside the navigator, but I can usually tell if it's bad by how loose the pods seem to be.
- Disassembling the Navigator. ...
- The Gearbox. ...
Full Answer
What is the best automatic pool vacuum?
BEST FOR CUSTOM-SHAPED POOLS: Dolphin Sigma Robotic Pool Cleaner with Bluetooth; BEST FOR VINYL POOLS: Polaris 9350 Sport Robotic Pool Cleaner; BEST FOR LEAVES AND GUNK: Dolphin Premier Robotic ...
What is the best vacuum for an inground pool?
The Best Pool Cleaners (Reviews & Guide)
- Dolphin Nautilus CC Plus. With the Dolphin Nautilus CC Plus, maintaining the cleaner is done with ease thanks to the top load filter.
- Polaris Vac-Sweep 280 Pressure Side Pool Cleaner. If you’re looking for a powerful pool cleaner, the Polaris Vac-Sweep 280 may be the right choice for you.
- VINGLI Automatic. ...
Why is my Hayward pool cleaner not moving?
Possible reasons for this problem include the following:
- The water level in the pool is too low. Make sure the water is high enough to cover all the skimmers—if there is more than one—and all the return jets.
- The suction hose for the vacuum has holes, or it isn't fully connected. ...
- The skimmer filter is dirty. ...
- Air is getting into the pump through the pump cover. ...
What is the best pool vacuum cleaner?
- BEST OVERALL: Dolphin Nautilus CC Automatic Robotic Pool Cleaner
- BEST MANUAL: U.S. ...
- BEST PRESSURE-SIDE: Polaris Vac-Sweep 360 Pressure Side Pool Cleaner
- BEST SUCTION-SIDE: Zodiac Baracuda G3 Advanced Suction Side Pool Cleaner
- BEST FOR ABOVE-GROUND POOLS: XtremepowerUS Automatic Pool Cleaner Vacuum

Why is my Hayward Pool Vac not moving?
There is an obstruction in the cleaner. Remove the consumer inspection plate at the bottom of the cleaner (one self contained screw needs to be loosened) and see if a rock, twig or large piece of debris has stuck between the bearings and turbine. Shake the head of the cleaner to dislodge any internal debris.
How do you take apart a Hayward pool vacuum?
3:397:01Hayward pool vac tear down (disassembly) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just turn the body will you turn the body over shake them out usually fall out like that oneMoreSo you just turn the body will you turn the body over shake them out usually fall out like that one did it fell over here I didn't see it at least it's in the area it's on the towel.
How do you take apart a pool vacuum?
1:513:04How to Remove a Pool Vac - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst step make sure that that pump is off. Second step unplug from the wall. Lay the tools out showMoreFirst step make sure that that pump is off. Second step unplug from the wall. Lay the tools out show you in a couple different ways you can lay it out lon nice long piece.
How long does a Hayward pool vacuum last?
On average, you can expect your automatic pool cleaner to last around 4 to 5 years.
How do I fix my pool vacuum?
0:122:13How to fix common problems with pool cleaners - YouTubeYouTubeStart of suggested clipEnd of suggested clipChange the settings so that the springs are less extended a pour cleaner that is moving very slowlyMoreChange the settings so that the springs are less extended a pour cleaner that is moving very slowly in your pool. Might indicate that you need to backwash and rinse the filter.
How do you replace the parts on a Hayward Pool Vac?
4:477:35How To: Repair a Hayward Navigator or Pool Vac Ultra Pool CleanerYouTubeStart of suggested clipEnd of suggested clipNote that the new flaps are marked rear in front make sure to install the proper flap in the frontMoreNote that the new flaps are marked rear in front make sure to install the proper flap in the front and rear of the unit's.
Why is my pool vacuum moving slowly?
When a suction cleaner is sluggish or slow, it's usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.
How do you unclog a pool cleaner?
2:383:36How to Unclog Debris Jammed in "The PoolCleaner" by ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we just knock it out I should usually fleet up sometimes you have to put your hand in there andMoreSo we just knock it out I should usually fleet up sometimes you have to put your hand in there and pull it out so check the hose lengths.
How do you replace Hayward Navigator pods?
0:383:06Hayward PoolVac & Navigator Pod kit AXV417WHP - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake this 1/4 wrench stick it in there and we'll take this off here. And the pod may come off easierMoreTake this 1/4 wrench stick it in there and we'll take this off here. And the pod may come off easier may be you may need a screwdriver to knock. It off the screwdriver here push it off there.
Why is my automatic pool vacuum not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
Why does my Hayward Navigator move so slow?
If your Hayward pool vacuum becomes too slow to clean your pool effectively, the vacuum likely has a blockage or the shoes and wings need to be replaced. Shoes and wings have wear indicators for determining when they require replacement.
Is it OK to leave pool vacuum in pool?
Cleaners aren't meant to stay in the pool 24/7. This is true for all cleaners. Pressure side cleaners run on a schedule every day so why take it out? Leaving the cleaner in the pool 24/7 increases its exposure to corrosive chemicals in the water, such as chlorine or shock.
How do you take a pool vacuum off the wall?
0:132:20An Easy Trick to Remove a Polaris or Pentair Wall Fitting ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne of the things you need to do first put the quick disconnect back in you want to simply removeMoreOne of the things you need to do first put the quick disconnect back in you want to simply remove the quick disconnect by taking this nut. And turning it and pulling it off the hose.
How do you replace pool cleaner tires?
1:022:31Changing the PoolVergnuegen Tires (896584000-143) - YouTubeYouTubeStart of suggested clipEnd of suggested clipReally easy to do you just pull the tire. Towards you comes right off and putting a new tire on aMoreReally easy to do you just pull the tire. Towards you comes right off and putting a new tire on a really easy hill just split it over these white notches. And you work your way.
Where does pool vacuum debris go?
Dirt and debris will be transferred through the vacuum plate and into the pump. It will then move through the sand filter. Depending on the chosen settings, the filter should capture the excess particles. Make sure to backwash your sand filter after you've finished vacuuming the pool.
How do I replace my pool cleaner?
11:1612:09Replacing the Poolvergnuegen "The PoolCleaner" Bottom, Removing ...YouTubeStart of suggested clipEnd of suggested clipIn then I'm going to push down the snap this one in again it sounds like you're gonna break it butMoreIn then I'm going to push down the snap this one in again it sounds like you're gonna break it but that's how they go in that's. It. That's how you changed the bottom out on the pool cleaner.
How to clean the screen on a pool vac?
Use the long-handled brush from the kit to clean the screen at the rear of the Navigator/Pool Vac Ultra. This screen allows water to flow into the Navigator/Pool Vac Ultra's steering mechanism. If the water flow is obstructed, the Navigator/Pool Vac Ultra steering cannot function properly.
What to do if your pool cleaner is not working?
If your automatic pool cleaner is not operating efficiently, it may be time to replace the parts that are designed to wear . If you see significant wear on your cleaners shoes, wings or flaps, replace these parts to improve performance, and to prevent damage to the more costly components.
How to replace rear flap on Hayward Navigator?
To replace the rear and front flaps, insert the screwdriver between the flap and the lower body, near the pivot point of the flaps. Gently pry the flap pivot point out or the hole in the body and slide the flap out. Repeat to remove the other flap. Click Here to View Hayward Navigator Replacement Parts.
How to replace Hayward Navigator shoes?
To replace the shoes, first turn the navigator on its back. Then insert a screwdriver between the shoe and the pod to pry the shoe off. Click Here to View Hayward Navigator Replacement Parts.
What happens when you push a shoe up against a pool pod?
When the shoe is pushed up against the end of the pod, the shoe should extend above the surface of the pod or the pod will start to rub against the pool floor. This shoe should have been replaced before the surface of the shoe had worn below the surface of the pod.
How to remove a wing from a scuba diver?
Remove the old wing by bending it slightly and lifting it off their hooks on the pod. Note: If any of the wing hooks are broken, you will have to replace the pod. See other "How To Guides".
Does the pool vac ultra have a flap?
Now inspect the Navigator/Pool Vac Ultra's flaps (rear and front) for wear and cracks. The picture at left shows an example of a worn rear flap that needs to be replaced.
Step 1
Turn your Navigator/Pool Vac Ultra pool cleaner over and look at the cleaner's shoes. The picture at left shows an example of badly worn shoes. When the shoe is pushed up against the end of the pod, the shoe should extend above the surface of the pod or the pod will start to rub against the pool floor.
Step 2
This picture shows a Navigator/Pool Vac Ultra with new shoes. Note how far the shoe extends above the pod surface.
Step 3
Next inspect the Navigator/Pool Vac Ultra's wings for wear and cracks. There is a wear line on each of the wings. When you can no longer see this line, replace the wings. The picture at left shows an example of a badly worn and broken wing. At 1, the wing has worn through by the peg that holds it in.
Step 4
Now inspect the Navigator/Pool Vac Ultra's flaps (rear and front) for wear and cracks. The picture at left shows an example of a worn rear flap that needs to be replaced.
Step 5
When replacing Navigator/Pool Vac Ultra parts, consider purchasing a pool cleaner tune-up kit. If one set of parts requires replacement, it's probably a good time to replace all of these parts. This kit includes a set of 4 shoes, a set of 2 wings, a set of 2 flaps (front and rear) and a screwdriver and brush to install the parts.
Step 6
For ease in replacing these parts, disconnect the pool cleaner from its hose. Pull the hose straight off to avoid breaking the internal gears.
Step 7
To replace the shoes, first turn the navigator on its back. Then insert a screwdriver between the shoe and the pod to pry the shoe off.
Step 1
Turn your Navigator/Pool Vac Ultra pool cleaner over and look at the cleaner's shoes. The picture at left shows an example of badly worn shoes. When the shoe is pushed up against the end of the pod, the shoe should extend above the surface of the pod or the pod will start to rub against the pool floor.
Step 2
This picture shows a Navigator/Pool Vac Ultra with new shoes. Note how far the shoe extends above the pod surface.
Step 3
Next inspect the Navigator/Pool Vac Ultra's wings for wear and cracks. There is a wear line on each of the wings. When you can no longer see this line, replace the wings. The picture at left shows an example of a badly worn and broken wing. At 1, the wing has worn through by the peg that holds it in.
Step 4
Now inspect the Navigator/Pool Vac Ultra's flaps (rear and front) for wear and cracks. The picture at left shows an example of a worn rear flap that needs to be replaced.
Step 5
When replacing Navigator/Pool Vac Ultra parts, consider purchasing a pool cleaner tune-up kit. If one set of parts requires replacement, it's probably a good time to replace all of these parts. This kit includes a set of 4 shoes, a set of 2 wings, a set of 2 flaps (front and rear) and a screwdriver and brush to install the parts.
Step 6
For ease in replacing these parts, disconnect the pool cleaner from its hose. Pull the hose straight off to avoid breaking the internal gears.
Step 7
To replace the shoes, first turn the navigator on its back. Then insert a screwdriver between the shoe and the pod to pry the shoe off.
What to do if your pool cleaner is not working?
If your automatic pool cleaner is not operating efficiently, it may be time to replace the parts that are designed to wear . If you see significant wear on your cleaners shoes, wings or flaps, replace these parts to improve performance, and to prevent damage to the more costly components. Click Here to Find Your Diver Dave & Wanda the Whale Parts.
How to clean pool cleaner steering?
Use the long-handled brush from the kit to clean the screen at the rear of the pool cleaner. This screen allows water to flow into the pool cleaner's steering mechanism. If the water flow is obstructed, the pool cleaner steering cannot function properly.
How to replace a pool shoe?
To replace the shoes, first turn the pool cleaner on its back. Then insert a screwdriver between the shoe and the pod to pry the shoe off. Click Here to Find Your Diver Dave & Wanda the Whale Parts. Click Here to Find Your Hayward Aquabug Parts.
What happens when you push a shoe up against a pool pod?
When the shoe is pushed up against the end of the pod, the shoe should extend above the surface of the pod or the pod will start to rub against the pool floor. This shoe should have been replaced before the surface of the shoe had worn below the surface of the pod.
How to remove a wing from a scuba diver?
Remove the old wing by bending it slightly and lifting it off their hooks on the pod. Note: If any of the wing hooks are broken, you will have to replace the pod. See other "How To Guides".
How to install a front flap on a sanitizer?
The rear of the unit has the screen in it. When installing the front flap, push the flap in place so that the pivot nibs engage the pivot holes in the body. Fold the flap in towards the bottom of the cleaner. There will be some resistance until the flap snap into place. Check that the spring is in place and that the spring action works freely.
