- The first step in repairing any underground sprinkler hose is to locate it. ...
- Dig an extra five inches underneath the broken pipe space. This will provide you with plenty of room to work on your repairs.
- Using a hacksaw, cut out the broken section. Measure 2″ on both sides of the cracked section and put marks on the pipe for accuracy as you cut.
- Replace the pipe section you cut out using a new piece of pipe. ...
- Finish up the sprinkler system leak repair by testing for leaks of your repaired underground sprinkler pipe.
Full Answer
How do you fix a broken sprinkler line?
A broken sprinkler line can seem like a difficult and expensive repair, but it’s actually pretty simple to do. First, find the leak by looking for escaping water or sprinkler heads with little to no flow. Then, dig up and expose the damaged pipe so you can remove it.
How to fix an exposed sprinkler pipe?
Clean off the section of exposed pipe with a wet cloth. To avoid getting dirt and debris in the sprinkler line when you make your repairs, wash off the section of exposed pipe. Use a clean cloth and water to scrub the dirt from it. Part 3
How to fix a leaking water hose?
Slip the cut end of the hose into the compression coupling and twist the collar clockwise to tighten the seal and secure your water hose repair. – Connect the new coupling to a faucet and nozzle and slowly turn the water on to check for leaks. That drip, drip, drip from the faucet is a waste of water and money.
How do you fix a broken hose on a lawn mower?
Make sure to match the damaged end of your hose to the new coupling so that everything fits correctly. Slip the cut end of the hose into the compression coupling and twist the collar clockwise to tighten the seal and secure your water hose repair.
How do I fix a hole in my irrigation hose?
0:001:10How To Repair Holes in Drip Irrigation Tubing - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a pair of pliers to grip the smaller of the two sides. Position over the hole to be plugged andMoreUse a pair of pliers to grip the smaller of the two sides. Position over the hole to be plugged and push in a popping. Sound should be heard indicating the goof plug is fully seated in the tubing.
How do you fix an underground sprinkler line?
1:025:32How to Fix A Broken Lawn Sprinkler line - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut you could use regular hose clamps if you didn't have these on hand the one downfall of these isMoreBut you could use regular hose clamps if you didn't have these on hand the one downfall of these is that you need this special tool that helps you pinch those clamps together.
Can you patch a punctured sprinkler line?
2:024:32Howto: fix a puncture in your sprinkler system - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically I just use this this tool here you can use whatever you can use a razor blade you cutMoreBut basically I just use this this tool here you can use whatever you can use a razor blade you cut it cut it right at the the crack.
How do you repair a hole in a rubber sprinkler hose?
If you have a rubber or silicone patch, you may be able to use 2 hose clamps on both ends of it over the hole in the pipe. Apply the patch to the hole in the pipe, then install a hose clamp on ether side to attempt to hole the patch in place and stop the water leak.
How do you fix PVC pipe in the ground?
4:0010:44EASILY Repairing Broken PVC Pipes(Least Amount Of Digging)YouTubeStart of suggested clipEnd of suggested clipClear a little bit of soil or sand out of the way. The next thing you're going to do is take aMoreClear a little bit of soil or sand out of the way. The next thing you're going to do is take a coupling glue it onto the pipe that you cut over here push it all the way down until it meets the stop.
How do you seal a sprinkler pipe?
0:334:28How To Repair A Broken Sprinkler Pipe with FiberFix - Product ReviewYouTubeStart of suggested clipEnd of suggested clipAnd it looks like gloves. Put on gloves get roll in a fiber flex in water for 10 to 12 secondsMoreAnd it looks like gloves. Put on gloves get roll in a fiber flex in water for 10 to 12 seconds remove excess water wrapped tightly around object rub to distribute resident evenly okay wrap tightly
How do you fix a hole in a pressurized PVC pipe?
0:261:07A Fast and Easy PVC Pipe Repair (Low Pressure Line) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe center of the c-clip over the hole I ran out of the PVC glue. But then added some more later onMoreThe center of the c-clip over the hole I ran out of the PVC glue. But then added some more later on around the edges of the c-clip. Let the glue dry for 24. Hours after the glue had dried.
How do I find a broken sprinkler wire?
0:232:43Using a Pulser to Troubleshoot a Sprinkler System Wire BreakYouTubeStart of suggested clipEnd of suggested clipThe receiver goes parallel with the wire path. And when you turn it on there's an analog meter thatMoreThe receiver goes parallel with the wire path. And when you turn it on there's an analog meter that you'll watch when the needle bounces to the right that's the direction of the fault.
How do you fix a broken sprinkler pipe under concrete?
Swab one end of the pipe with PVC glue and then press a PVC coupler onto the end of the pipe. Swab the end of the exposed section of pipe that you cut from with PVC glue and press the other end of the coupler onto the pipe. This will seal the connection on one end of the concrete.
How do you fix a broken PVC sprinkler pipe?
0:253:543 Ways to Repair PVC Irrigation Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip theMoreSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip the coupling over one section of the pipe. And then over the other tighten. The nuts.
How do you know if your sprinkler pipes burst?
0:313:21Finding leaks in your in-ground sprinkler system - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf it keeps moving the leak is inside your home you can now watch our video on finding leaks if theMoreIf it keeps moving the leak is inside your home you can now watch our video on finding leaks if the low flow indicator stops. Moving the leak is in your main sprinkler system pipe.
How to find a leak in a sprinkler system?
After you turn on the sprinkler system, walk through the area where the sprinkler system is installed. Listen for running water and walk towards where you hear the sound to locate the leak in your sprinkler line .
How to tell if a sprinkler line is leaking?
Once you’ve identified where the leak is, mark the location so you can find it when the water is turned off.
Where is the break in the water line located?
The break or leak in the water line will be located between the last working sprinkler head and the first nonworking one.
How to stop water from leaking in a water line?
If you’ve found the signs of a leak and located the region where the line is leaking or broken, turn off the water so you can repair the line. Use the shut off valve in the control box to stop the flow of water through the system. Wait 1-2 minutes to allow the water to finish flowing through the system.
How to extend a plastic pipe?
Insert a slip coupling into the pipe. A slip coupling is a plastic pipe that is flexible and allows you to extend it to the length that you need it to be. Slide the end of the coupling into 1 end of the exposed pipe. Then, extend the coupling so it fits into the other end of the pipe.
How wide should a pipe be?
Make the whole wide enough so the pipe is exposed for 6 inches (15 cm) on each side.
What does a larger break in a system mean?
A larger break in the system could mean a costly repair.
How to repair a hose that is damaged?
Compression mender. Cut the Hose. Use a sharp pair of scissors, a hose cutter or a razor knife to cut out the damaged hose section. Be sure to make clean cuts, with no ragged edges. Install a Compression Mender. A compression mender gives a quick, yet secure, fix without any special tools.
How to tighten a water hose?
Slip the cut end of the hose into the compression coupling and twist the collar clockwise to tighten the seal and secure your water hose repair .
How to repair a water hose with a bent coupling?
A bent coupling will leak when connected to a faucet or sprinkler, while a crushed one cannot be connected at all. Use a compression coupling for a brand-new hose end.
How to fix a hose with compression mender?
A compression mender gives a quick, yet secure, fix without any special tools. Simply slip each cut end into the compression mender and twist the collar clockwise for a watertight seal. Inspect Your Work. Slowly turn the water on to make sure the hose repair seal is secure.
What to do if your faucet drips?
That drip, drip, drip from the faucet is a waste of water and money. If you recently noticed a drip coming from your hose, you’re probably looking for information on how to fix a garden hose leak. A worn-down washer may be the problem. Replace your old washer with Gilmour’s Flexogen Hose Seal for a water-tight seal.
What are the ends of a garden hose?
Make sure the edges are nice and clean. Choose the Fitting. The ends of your garden hose feature two different compression couplings: a female and a male. Female ends connect to the faucet, while male ends connect to your nozzles or sprinklers.
Can you replace washers on sprinklers?
You can use the same steps to replace worn washers and seals on sprinklers, nozzles and connectors.
