To troubleshoot this issue:
- Disconnect the appliance from mains power and leave it in the powered off state for at least two minutes.
- Reconnect the power supply.
- Wait a further 30 seconds and then try to start the machine again.
- Watch for a repeat of the error code. If it appears again, contact Hotpoint repair services.
Full Answer
Why is my Hotpoint washing machine not spinning?
Why Is My Washing Machine Not Spinning
- Drain pump blockage. One of the most common reasons why your washing machine has stopped spinning is when it can’t drain properly due to a blocked drain pump.
- Imbalanced drum. When the load is too heavy for the machine, or sometimes if you are trying to wash one large item on its own, the appliance detects a risk.
- Motor brushes worn out. ...
How do you take apart Hotpoint washing machine?
How to Take Apart a Washing Machine
- Lift off the end caps which sit on the console by prying them from the back of the washer. Remove the screws under the end caps.
- Fold the console over to the back of the washing machine. Let it hang in place by the plastic hinges that hold it.
- Locate the two large brass clips under the console. ...
- Open the lid of the washer and remove the washer casing. ...
Is Hotpoint a GE Appliance?
Hotpoint is backed by GE Appliances Service. Hotpoint appliances are serviced by certified GE Appliances technicians. You can schedule service online 24 hours a day. Or you can call GE Appliance Service at 1-800-GECares (1-800-432-2737) to schedule a service appointment. Register Your Hotpoint.
Does Hotpoint appliances sell washers and dryers?
Washers & Dryers. Hotpoint washers and dryers can wash large loads of clothes, which means less time doing laundry. Designed to clean gently but effectively with a large washer tub, our washers feature a choice of special cycles to take extra care of every load.
What are the common problems in washing machine?
Common Washing Machine Problems and SolutionsVibrating Washer.Leaky Washer.Noisy Washer.Washer Won't Run.Washer Won't Drain.Detergent Won't Dispense.Smelly Washer.
How do I troubleshoot my Hotpoint washing machine?
0:034:52Hotpoint Washer Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy hotpoint washing machine is stopping mid-cycle. We recommend you check that your cold waterMoreMy hotpoint washing machine is stopping mid-cycle. We recommend you check that your cold water supply is on this is a common cause of your appliance failing to fill on the rinse cycle.
How do I reset my Hotpoint washer?
Motor Reset Procedure:Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ... The motor has now been reset and is ready for you to start a cycle.
Why is my Hotpoint washer not draining or spinning?
If the washer won't drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
How do you read Hotpoint error codes?
What do your washing machine error codes mean?F01 — Electronic circuit board fault. ... F02 — Motor circuit fault. ... F03 — Temperature sensing fault. ... F05 — Waste pipe blockage or pump issue. ... F06 — Door lock fault. ... F07 — Electronic circuit board fault / heating circuit fault. ... F08 — Heater fault. ... F09 — Software fault.More items...
How do I reset my washing machine?
1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Does a Hotpoint washing machine have a reset button?
If the on/off or reset button on your Hotpoint washing machine has cracked, fallen off or worn out then it can be very difficult for you to be able to switch on your machine. Simply replace it with this genuine replacement button. This part is suitable for selected Hotpoint Washer Dryers.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.
Why is my Hotpoint washer not starting?
If the electrical outlet is receiving power, but the washer won't start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
What causes a washing machine not to drain and spin?
If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do you fix a washing machine that won't drain?
What to Do When Your Washing Machine Won't DrainPerform a Master Reset. Unplug your washer for about one minute. ... Test the Lid Switch Assembly. ... See if the Drain Hose is Kinked. ... Check the Drain Hose or Pump for Clogs. ... Clean out the Coin Trap. ... Check the Water Level Control. ... Schedule Washing Machine Repair.
How do you fix a washer that won't spin?
How To Fix A Washer That Won't SpinLighten the load inside the washer. ... Rebalance the load in the washing machine. ... Check or repair the washing machine drain hose. ... Check for blown fuses. ... Check the washing machine lid safety switch. ... Replace the drive belt in your washing machine. ... Replace the motor in your washing machine.
Why are all the lights flashing on my Hotpoint washing machine?
End light flashing Indicates that the Hotpoint washing machine has reached the end of a wash programme. If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe.
Why is my Hotpoint washer not starting?
If the electrical outlet is receiving power, but the washer won't start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
Why does my washing machine get stuck on the wash cycle?
If your top load washing machine (or some older front load washers) is stuck on one continuous cycle and will not advance and forward to the next wash cycle, then most likely the washer timer is faulty and needs replacement. The timer on your washing machine controls all aspects of the wash, spin, and rinse cycles.
Why is my Hotpoint washing machine not filling with water?
If you are getting a flow of water through your hose but your washer is still not filling with water then the problem could be with your water valve. If you're lucky the issue might simply be that the filter needs cleaning, be careful with your water valve filter though because many of them are very fragile.
When was the Hotpoint washer invented?
The name Hotpoint comes from the hot point of the revolutionary first electric iron of 1905 , invented by an American. No need to call an expensive Hotpoint washer serviceman, and then wait a couple of hours (or DAYS) for him to show up! Diagnose your problem RIGHT NOW, cheaply and easily, with our FREE ONLINE Hotpoint washing machine repair manual!
What are the symptoms of a hotpoint washer?
Diagnosis and repair procedures are included for the most common symptoms, such as leaking, slowly or not filling, clothes too wet after cycle ends, no agitate, not spinning, not draining, timer, drive motor, electrical troubles and other Hotpoint washer problems .
What is the phone number for Hotpoint washing machine?
If you need further assistance please call Hotpoint customer service on 0344 822 4224. My Hotpoint washing machines is leaking. As part of the manufacturing process we thoroughly test your washing machines to ensure that it will not leak from any internal components after you have installed it.
Why does my Hotpoint washer light flash?
The most common are: Pre wash light flashing. Indicates that the Hotpoint washing machines is failing to fill correctly. Check your fill hoses to make sure they are turned on correctly.
Why is my washing machine leaking?
It’s also possible for a leak to appear from your detergent dispenser, which can be caused by excessive water pressure or the washing machines has not been levelled properly during installation.
What is the phone number for Hotpoint?
If you need further assistance please call Hotpoint customer service on 0344 822 4224. My Hotpoint washing machines is noisy and unstable. If your Hotpoint washing machines appears noisy or unstable when using it for the first time it’s possible the installation has not been completed properly.
3. Hotpoint Washer Making A Loud Noise
The first thing you should do is make sure that the agitator/spinner is not hitting anything inside the tub. If it is not, and if this is a brand new washer, then you may have a loose connection somewhere.
4. Water Level Too Low
This condition occurs when there is a leak in the water supply line or the drain hose. In either case, the water level gets too low very quickly and the agitator stops turning.
5. Faulty Machine Pump
This is the least common washing machine problem. It occurs when the impeller of the washing machine’s pump becomes worn and stops turning. This causes the water level to get very low very quickly and the agitator/spinner will eventually stop turning.
6. Worn Out Drive Belt
This is another most common mechanical problem with Hotpoint washing machines. As the name implies, a drive belt goes around an idler pulley that holds the agitator/spinner, and two main pulleys that hold the motor.
7. Washing Machine Not Filling Up
This is when the washing machine is not getting full of water during a cycle. In other words, you may notice that your washer is only using a small amount of water during the entire cycle.
What happens if a washer spring breaks?
If a spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation. Inspect the counterbalance springs to determine if any of the springs are broken. If a counterbalance spring is broken, replace it. Additionally, check the frame where the counterbalance springs are attached. If the frame is rusted, replace it.
Why does my washer tub shake?
The suspension springs help to absorb the movement of the washer tub. If a suspension spring breaks, the tub might become unbalanced , causing it to shake and vibrate during operation. Inspect the suspension springs to determine if any of the springs are broken. If a suspension spring is broken, replace it.
What does a suspension rod do on a washer?
The suspension rods help to dampen the movement of the washer tub. If one or more of the suspension rods are broken, the washer will vibrate or shake. To determine if the suspension rods are at fault, check the rods to determine if any of them are broken. If a suspension rod is broken, replace it. Required Part.
What happens if a washer shock absorber is worn out?
The shock absorbers dampen the vibration of the washer tub. If one or more of the shock absorbers are worn out, the washer will vibrate or shake. Sometimes, when a washer is moved to another location, the shock absorbers can separate.
