How to fix ice maker on maytag refrigerator causes & fixing Cause1. Water valve. Fixing: Step1: in determining whether our water valve is working properly or not is check your water supply: 1) pulling the refrigerator forward, enough that we can access the back of it. 2) locate the manual shut-off valve and turn off the water supply.
How much Freon do you put in a Maytag refrigerator?
You can use a refrigerant charging cylinder or sensitive scale to weigh in the refrigerant 5,5 ounces of R-134a.... or since you do not have a scale, let liquid refrigerant into the valve you have fit into the suction line to admit *liquid refrigerant, with the compressor OFF... for 10 seconds. Then let it sit for 15 minutes.
How to fix Maytag refrigerator not cooling, Part 1?
Common solutions for: Why is My Maytag Refrigerator Not Cooling?
- Condenser Coils are Dirty. The condenser coils are usually located under the refrigerator. ...
- Condenser Fan Motor. The condenser fan motor draws air though the condenser coils and over the compressor. ...
- Evaporator Fan Motor. ...
- Start Relay. ...
- Temperature Control Thermostat. ...
- Start Capacitor. ...
How to remove the icemaker from a Maytag?
What do you need to clean the ice maker?
- Turn off the ice maker.
- Wait 5 to 10 minutes for the ice to fall into the storage bin. ...
- Unscrew the drain cap from the bottom of the water pan located inside the storage bin as shown. ...
- Replace the drain cap securely on the water pan. ...
- Read and follow all handling information on the cleaner bottle before completing the steps below. ...
How do I fix the ice maker in my Refrigerator?
If your ice maker has frozen up, take the following steps to thaw it out:
- Unplug the refrigerator or turn off the circuit breaker that supplies power to it. ...
- Find the fill tube. ...
- Warm the hose and surrounding mechanism. ...
- If you don’t want to use a hair dryer, you can soak the supply tubing with hot water, using a turkey baster and catching the overflow in a bowl. ...
See more
Why is my Maytag refrigerator not making ice or water?
Make sure the water supply is properly connected to a cold water supply and the water shutoff valve is fully opened. Check to make sure there are no kinks in the water supply line. A kink in the line can reduce water flow. Straighten the water source line to restore adequate water flow and pressure.
Why is my fridge ice maker not making ice?
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How do you unfreeze a Maytag ice maker?
2:514:01Ice maker FROZEN over - how to FIX your freezer machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I needed to clean it out a bit and kind of get things moving again line up your ice maker withMoreSo I needed to clean it out a bit and kind of get things moving again line up your ice maker with the water pipe and the brackets that hold it in place reconnect. The power screw.
Why is my ice maker not working but water does?
Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won't fill with water to make ice, replace the water inlet valve.
Why did my Maytag refrigerator stop making ice?
There are several reasons you may find your ice maker not working all of a sudden, including a blocked water dispenser, issues with your water supply line, or a clogged water filter.
How do I test my Maytag ice maker?
2:2120:28How to Test and Replace Maytag/Whirlpool Gold Ice Maker ...YouTubeStart of suggested clipEnd of suggested clipYou have to get into diagnostics. And you do that by shutting. The left door holding the twoMoreYou have to get into diagnostics. And you do that by shutting. The left door holding the two leftmost buttons on the display hold it for three seconds.
Is there a reset button on Maytag ice maker?
Try a Simple Reset If it is not a mechanical or parts failure, this simple fix may get your ice maker working again. Most ice maker models also have a reset button. Models with a display panel can be reset by consulting your manual for the reset instructions.
How do I unblock my ice maker?
Apply heat with a hairdryer to the ice maker fill tube, which is usually a white, rubber-like hose. Hold the nozzle of the hairdryer at the front of the ice maker so that the heat will blast into the fill line. Set the hairdryer to its lowest heat setting to avoid melting the plastic lines and parts of the ice maker.
Will unplugging my fridge reset the ice maker?
This will force the ice maker to run water and begin the process of creating ice. For models that have an on/off switch, you should turn the switch off and unplug the refrigerator. Leave the refrigerator unplugged for 5 minutes. This will allow the ice system to reset.
Where is the reset button on my ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
How do I force my ice maker to cycle?
If your gear has a small notch in it, then you may need a flat-head screwdriver. Use it to turn your gear counterclockwise until you hear the mentioned click. In both situations, the click that is heard will force the ice maker to cycle.
How do I reset my ice maker?
Unplug the machine and wait 10 seconds. Plug the machine back in and press the ON button. You should see a blue light appear, letting you know that the machine has been reset.
Where is the reset button on Frigidaire ice maker?
Where to Find the Reset ButtonIce Maker BrandWhere to Find the Reset ButtonFrigidaireThe reset button is on the front of the ice maker, under the motor housing, past the front coverGESome GE ice makers do not have a reset button. To reset one, try turning the ice maker off at the power source.3 more rows
What do you do when your ice maker stops working?
4:195:02Ice Maker Not Working? - Check these 6 Things first! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the water line you want to make sure it's not kinked it's not clogged. So how to do that is youMoreAnd the water line you want to make sure it's not kinked it's not clogged. So how to do that is you pull the fridge out make sure it's unplugged. Turn the water. Off that supplies the fridge with the
How do you troubleshoot an ice maker?
Ice Maker Troubleshooting GuideCheck the shutoff arm.Check the supply valve.Inspect the water supply line.Test the shutoff switch.Check the freezer temperature.Inspect the ejector gear.Test the ejector motor.Test the ice mold heater.More items...
What causes an ice maker to stop working?
There are several reasons you may find your ice maker not working all of a sudden, including a blocked water dispenser, issues with your water supp...
Not dropping ice
If your ice maker is not dropping ice, it could be that there’s a blockage in the ice tray, or an ice cube is jammed between the bin and the lever....
Not making enough ice
There could be several reasons your ice maker might not be making enough ice, including low water pressure or a kink in the water line. To check if...
Not making any ice
The culprits behind your ice maker not making any ice may cover a wide range, as listed below:Make sure your freezer’s thermostat is set to 0ºF for...
Leaking into freezer or on floor
Water leaking from the ice maker could mean that either your refrigerator or ice maker isn’t level. A faulty water line could also be responsible.L...
Ice is too small or tastes funny
Ice that has a weird taste or ice cubes that come out too small could be caused by the water line, or food odors from your freezer being absorbed b...
Is the Water Supply Line Connected to the Ice Maker?
Check that the water supply line is connected to the ice maker. Also, check that the water is turned on.
Is There a Diagnostic Function?
Some Maytag refrigerators will have a diagnostic function that may be able to identify the problem for you . Check the refrigerator’s manual or tech sheet for instructions to operate the diagnostic mode and interpret the results.
Is the Temperature Correct?
For your Maytag ice maker to work correctly, the freezer temperature should be between 0 to 5 degrees Fahrenheit (-18 to -15 degrees Celsius). Checking and adjusting the refrigerator and/or freezer temperature may get the ice maker working again. If the temperature is too high, cleaning debris off the refrigerator condenser coils will often fix the issue.
What to do if ice tray thermostat is bad?
If there is a fault with the ice tray thermostat, the ice maker will not know when water is required or when ice should be emptied from the ice tray. If you suspect the ice tray thermostat, test it with a multimeter for continuity. If defective, on most models the ice tray thermostat can be removed and replaced.
What to use to defrost ice maker?
Depending on where the ice blockage or freeze has occurred, you may be able to use a dishcloth with hot water, a blow dryer, a defrost tool, or a defrost function—or remove the ice maker from the refrigerator to allow it to defrost—to solve the issue.
Why does my Maytag ice maker stop working?
In most cases, the ice maker stops working because of ice build-up or the need for a new water filter. The next most common cause is a fault with the water inlet valve, which is relatively easy to check and replace. Read on to get your Maytag ice maker working again.
Why does my ice maker hum?
The water inlet valve can become defective if the valve becomes blocked with mineral deposits, which stop the part from opening. An unusual hum coming from the refrigerator when the ice maker should be filling up with water indicates a blocked valve. If the valve is blocked, it is recommended that the valve be replaced.
Is the ice maker turned on?
Verify that the ice maker is turned on. If the ice maker’s water supply is not connected to water supply line, turn the ice maker off. If the ice maker is on, but disconnected to water supply line, the following could happen:
How to fix ice maker that is jammed?
First, ensure that ice is not jammed in the ejector arm of the ice maker. Remove jammed ice from the ejector arm using only a plastic utensil so the ice maker is not damaged. This will likely resolve the issue. Because the ice may not be completely frozen yet, when the harvest fingers try to harvest the ice cubes, the fingers bring up icy water that attaches to the stripper. This icy water can then freeze on the stripper during the next cycle causing an ice bridge. This ice bridge will cause the harvest fingers to jam.
What happens if the ice maker is on but disconnected?
If the ice maker is on, but disconnected to water supply line, the following could happen: The ice maker will continue to try to make ice, causing a buzzing sound. A refrigerator section may to be too cold.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
Why do harvest fingers jam?
Because the ice may not be completely frozen yet , when the harvest fingers try to harvest the ice cubes, the fingers bring up icy water that attaches to the stripper. This icy water can then freeze on the stripper during the next cycle causing an ice bridge. This ice bridge will cause the harvest fingers to jam.
What causes an ice maker to stop working?
There are several reasons you may find your ice maker not working all of a sudden, including a blocked water dispenser, issues with your water supply line, or a clogged water filter.
How to check if ice maker is working?
To check if that may be the case, follow the steps below. Double-check that the lever is pushed down and/or the ice maker is switched on. Unplug your refrigerator. Cut off the water supply. Move your refrigerator to access the water line. Disconnect the water line and place it in a bucket or in your sink.
Why is my ice maker not dropping ice?
If your ice maker is not dropping ice, it could be that there’s a blockage in the ice tray, or an ice cube is jammed between the bin and the lever. If this happens, here are some things you can do:
Why does ice taste so small?
Ice that has a weird taste or ice cubes that come out too small could be caused by the water line, or food odors from your freezer being absorbed by the ice. Check your water line and look for any kinks, bulges or damage. If you see any, you’ll need a replacement.
Why does my water line stop flowing?
A frozen water line or a kink in the water line may cause the water flow to slow or stop altogether. Ensure the house water line is turned on and free of kinks as well.
How to get ice out of a fridge?
Remove the ice bin to see if there’s ice accumulation. Remove any blocked ice by carefully chipping at it with a plastic knife. If the ice is too large, you may have to let the ice melt by defrosting your fridge. 2.
What to do if ice is too large?
If the ice is too large, you may have to let the ice melt by defrosting your fridge.
Replacement Icemaker for Maytag ICE Ice maker not making ice
Step by step instructions on how to replace a Replacement Icemaker for Maytag ICE Ice maker not making ice #AP4135008 Read More...
My Repair & Advice Featured Story
My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself.
My Repair & Advice
Replaced icemaker with part from Appliancepartspros.com. Your video explained the process in detail and made the replacement very simple. Replacement part fit perfectly and arrived in less than 24 hours of placing my order.
My Repair & Advice
Searched online for ice maker found appliancepartsPros.com selected my ice maker it came very quickly I installed it in just a few minutes shortly afterward I had ice.
Water Valve Single for Maytag ICE Ice maker not making ice
Step by step instructions on how to replace a Water Valve Single for Maytag ICE Ice maker not making ice #AP3103467 for Read More...
My Repair & Advice
With parts I ordered from you with your help. Followed video and paper instructions.
My Repair & Advice
The hardest part of the problem was finding the proper place to find areplacment parts. Once I found Appliance Pro all when smooth. The second hardest part was moving the frig out from the wall but after i recieved ther part in 2 days as promised and it was a simple task to disconnet the water flow tube and elec connect.
What to do if icemaker has ejector blades?
If the icemaker module has ejector blades, check to ensure that ice cubes are not stuck in the blades. There are usually test points in the module that a technician can use to further diagnose problems with the module.
What temperature should an ice maker be when the thermostat contacts are open?
open. If the thermostat contacts are open, the ice maker will not make ice. The ice maker temperature must generally be lower than 20 degrees Fahrenheit for the thermostat contacts to close.)
What is an icemaker module?
The icemaker module is equipped with a motor that cycles the ice ejector arms or turns a tray to eject the cubes into the ice bucket. When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes. At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water. If the icemaker module is defective, the ice maker won’t make or dispense ice. First, depending on your model, make sure t...
How does an ice maker thermostat work?
The icemaker mold thermostat monitors the temperature of the ice mold (ice tray). Once the mold reaches the proper temperature, the icemaker ejects the ice cubes and refills the ice mold with water. If the mold thermostat is defective, the ice maker will stop making ice. To determine if the thermostat is defective, use a multimeter to test it for continuity. If the mold thermostat does not have continuity, replace it. (Note: If the ice maker is not cold enough, the mold thermostat contacts will ...
What is an ice maker inlet valve?
02 - Water Inlet Valve. The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice.
What temperature should an ice maker be?
The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear ...
How much pressure does an ice maker need?
As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve.
