The following are the steps on how to repair inflatable bounce house:
- Create round PVC patches right for the size of the area to be covered. Round is preferable to prevent corners from lifting. ...
- Using the sandpaper, sand the surface of the bottom patch and the surface of the inflatable.
- With your brush, apply a substantial amount of glue to the patch, including its edges. Do the same on the side of the inflatable where the piece will adhere.
- Ready your hairdryer and heat the patch and inflatable's surface.
- When the glue becomes sticky, place the patch over the area to be covered.
- Continue heating above the patch.
- With the use of a roller, remove trapped air from the patch.
- Leave the patch to dry thoroughly.
How to repair a tear in a bounce house?
If you’re repairing a tear on the bounce house, you will now follow the steps above for applying a bounce house patch using a Bounce House Patch Kit (link to Amazon). Sewing a tear with the awl kit and then applying a patch is the most permanent professional bounce house patch repair that you can do.
How to repair a bounce house netting?
Sewing a tear with the awl kit and then applying a patch is the most permanent professional bounce house patch repair that you can do. Fixing the netting on a bounce house in a professional way takes some time and involves some weaving skills.
How do you apply a bounce house patch?
Some larger bounce houses have zippers that can open up and give you access to the inside of the bounce house. This is the best place to apply the patch because the pressure when inflated will be pushing the patch more into place, rather than the air pressure pushing the patch outwards.
How do you tell if a bounce house is inflated?
The simplest way is to walk around the bounce house while inflated and the blower running and feel for any air escaping the bounce house where it shouldn’t be. For most bounce houses you won’t be able to hear where the air is escaping, and they will be too large to submerge them in water.
How do you repair a ripped seam on a bounce house?
0:101:48Repair Damaged Stitching using a Sewing Awl Kit: HOW TO | Magic ...YouTubeStart of suggested clipEnd of suggested clipArea. With your sewing awl kit push the needle through the vinyl and pull the end of the thread allMoreArea. With your sewing awl kit push the needle through the vinyl and pull the end of the thread all the way out. Pull out enough thread to cover the entire torn.
What kind of glue do you use to patch a bounce house?
vinyl cementSimply apply the vinyl cement to the cleaned area on the unit and also on the secondary vinyl (patch or what you are gluing to the inflatable). The vinyl cement needs to dry for a couple of minutes to become tacky then apply together with pressure for a few minutes.
How do you fix a hole in an inflatable bounce house?
Steps To Apply A Bounce House Patch:Clean the area to be patched.Cut the patch into the shape of a circle.Flatten the cut areas.Apply vinyl glue around the leak.Apply vinyl glue to the patch.Press the patch on and apply pressure.Check that edges are sealed.
Can you patch a bounce house with duct tape?
Quickly fixing a hole in a bounce house If you own small bounce houses, then can instantly fix the hole by using some duct tape over the hole. You need to remember that this trick works only on small holes and not for large ones.
How do you repair vinyl inflatables?
0:255:08Repairing Inflatable Pin Holes, Punctures, and Tears - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first step and one of the most important is to deflate the toy completely before attempting anyMoreThe first step and one of the most important is to deflate the toy completely before attempting any repairs. Most solvent glues for repairing vinyl temporarily make the vinyl very soft.
Can You Use Flex Seal on a bounce house?
0:021:532018.10.14 - Using flex-seal tape to fix bouncy houses - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe just apply that right in there and it sticks all the time keeps all that air from coming out andMoreWe just apply that right in there and it sticks all the time keeps all that air from coming out and it's got a nice clean.
How do you find a hole in an inflatable bounce house?
0:044:31How to Check & Repair Air Leaks for your Inflatables - YouTubeYouTubeStart of suggested clipEnd of suggested clipFull of dish soap and water and then spray the entire piece down looking for bubbles.MoreFull of dish soap and water and then spray the entire piece down looking for bubbles.
How do you fix a cut in a bounce house?
If the material in your bounce house is torn, you can repair it with a patch. You can purchase a vinyl repair kit or use the one that came with your bounce house. A vinyl repair kit has patches made from tough material that can resist punctures and tears and an adhesive that will bond to the vinyl in your bounce house.
How do you seal seams on bounce castle?
0:381:51How to patch a leaking seam with repair tape - Bounce House TutorialYouTubeStart of suggested clipEnd of suggested clipJust make sure that the edge of your tape is anchored and secure to the vinyl. Before you startMoreJust make sure that the edge of your tape is anchored and secure to the vinyl. Before you start peeling off the rest of it. So I'm going to keep the rest of the seam stretched out and firm.
Can you use epoxy on inflatables?
3:304:16How To: Inflatable Repair Adhesives Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll want to use G flex epoxy G flex is a very strong and flexible epoxy that will stick to justMoreYou'll want to use G flex epoxy G flex is a very strong and flexible epoxy that will stick to just about anything as long as the surfaces are prepared properly.
What glue is good for vinyl?
Polyurethane glue is ideal for gluing thinner flexible vinyl together as well as gluing vinyl to other surfaces like wood or plastic.
How do I prevent rips and tears in my Bounce House?
Choose an appropriate site that is free of sticks and rocks - Store your bounce house properly - Set rules for children, including a no shoe policy.
How much does it cost to repair a Bounce House?
Vinyl Repair Kits, Sewing Awls, and other tools you may need will ultimately determine the total cost. For a rough estimate, let’s call it $10-30....
How do I repair any netting on the Bounce House?
You could sew the netting back together with the right equipment (needle, string, etc).
How to repair a ripped bouncy castle?
The use of glue and patch to repair ripped sections of the bouncy castle is another quick fix you can do. The method may not be as sturdy as stitching, but it’s still an effective means of restoring torn castles. Here are the things you need to prepare to pull off a DIY inflatable bounce house repair:
How to glue a patch to an inflatable?
With your brush, apply a substantial amount of glue to the patch, including its edges. Do the same on the side of the inflatable where the piece will adhere.
Can you repair an inflatable bounce house?
With the right knowledge on how to repair inflatable bounce house, there is no need to panic when your baby’s castle sustains damages. You won’t even have to spend a lot on repair, and it’s needless to buy a new one. A DIY bounce house repair can last long when done pretty well. Just make sure to follow this guide, and your inflatables are good to go! Find out more about play pens.
Can you repair a bounce house with tear tape?
You can still manage to fix small tears in the bounce house while it’s all set up using tear tape. You can purchase an inflatable repair tape from various camping shops. You can buy them in small packets or larger rolls. Here’s how to repair inflatable bounce house using tear tape.
When glue becomes sticky, where to place patch?
When the glue becomes sticky, place the patch over the area to be covered.
Do you have to repair in section or in a single run?
Repair in section instead of doing it in a single run, so when the stitches wear out someday, it’ll come off in parts. This way, you don’t have to stitch the whole stretch again.
What does it mean when a part is sticking up?
Any part that is sticking up is a part that will not properly bond. Add more glue if need be, or, get a heavier object to press down upon the patched leak.
How to get a patch to not stick?
First, make sure the patch is flat and not stuck to another piece of itself. After that, you have two choices . One, sit there and hold the pieces together for several minutes. Or two, find a heavy object and get it to do the job of maintaining an adequate amount of pressure on the patch site. Your choice.
What to use to make bubbles last longer?
If all else fails, you’re going to want to turn to soap and water. Some folks recommend mixing in some glycerin, which is useful for retaining the effectiveness of the bubbles you’re about to create - using a detergent helps to lower water’s surface tension, which in turn enables bubbles to last longer.
Can you use corn syrup in a bounce house?
You will want to properly clean your b ounce house if you’re going to add in a third party adjunct (ie - the glycerin, corn syrup, or other substitute).
How to fix a leaky bounce house?
Another quick fix options is to get some Vinyl Repair Tape (link to Amazon) and tape over the leak with that. For us, this has had more success than a duct tape fix, but still is not a long term solution. This could work great for smaller bounce houses. The problem is, after enough use, the tape starts to pull up and air starts leaking out again.
What to do if your bounce house is tearing?
Sewing a tear with the awl kit and then applying a patch is the most permanent professional bounce house patch repair that you can do.
How to make soapy water for bounce houses?
1 Tbsp glycerin. 1 Gallon of water. Combine, shake, and use to coat the bounce house a couple square feet at a time. I’ve done this without the glycerin, just using soap and water, and was able to locate a small leak.
Why is my bounce house discolored?
If you’re discoloration is from mold, mildew, or something else, your bounce house could benefit from a good cleaning. Check out my How To Clean A Bounce House article for a step by step walk through of the proper cleaning process.
How to tell if a bounce house has a hole?
The simplest way is to walk around the bounce house while inflated and the blower running and feel for any air escaping the bounce house where it shouldn’t be .
How to find a leak in a sandbox?
Ways To Find A Leak: 1 Feel for air escaping 2 Submerge in water (only viable for small models) 3 Coat with soapy water 4 Listen for air escaping
What can prevent a patch from sticking?
Dirt and debris can prevent the patch from sticking properly. Make sure the area you will be applying the patch is free from water, grease, dirt, and any other debris.
How big of a damage to an inflatable bounce house?
If the damage to your inflatable is larger than 6 inches, we recommend having it repaired by a professional bounce house repair center.
How to contact Magic Jump Inc?
website visitors. If you are a bouncer repair company and would like to be included in this list of inflatable repair centers, please contact us at 818.847.1313 or email us at [email protected].
What is a Magic Jump Repair Kit?
Our Repair Kit provides a fast and easy solution for small cuts and punctures. Your order of a Magic Jump Repair Kit includes multi-colored vinyls and 8-ounce vinyl cement. Make sure to have this Repair Kit handy when accidents happen.
Is it safe to use tear aid on inflatables?
Tear-Aid patches should be considered a temporary fix and should never be considered a safe permanent fix for tears or torn seams to an inflatable.
Do I need to Patch Everywhere that I feel Air Coming Out?
This is not the case. You bounce house will most likely always have air seeping through the seams and built-in pockets at the top for air to flow out. This is actually an amazing feature of your bounce house as the constant stream of air flow is what keeps it so strongly inflated while so many little bodies jump all over it. The continuous air flow is what makes it different from a balloon that could pop at any moment and essentially adds to the incredible durability of the inflatable.
How to repair a tear in a vinyl window?
This repair is done by gluing an extra piece of vinyl on the inside of the tear as described above and then puncturing precise holes through both pieces of vinyl. Make sure the area is completely cleaned and dry before starting the process. Using a curved needle and special string you essentially sew the tear together. When the hole is sewn, another patch of vinyl is glued on top. Similar to the repair described above, try to get every air pocket out so that the vinyl patch can seal securely. Because you will now have the sewn pieces under the repair, take your time to firmly press out any bubbles carefully with your fingers and press firmly around the bumps of the sewn tear.
How to fix a tear in vinyl patch?
Clean the area with a fast-drying alcohol swab and make sure it is dry before putting on the glue. Brush on the vinyl cement glue onto both the tear and the vinyl patch. Press the two together keeping it as flat as possible. Use a towel so that the glue does not get on your hands. Try to remove any air pockets.
How to repair a rip in a car?
Using a repair kit with the necessary materials, poke holes around the rip and sew the two sides together and then glue a vinyl patch on either side of the sewn tear.
Can duck tape be used on bounce houses?
It is not recommended to use Gorilla Tape or Duck Tape to repair a bounce house. Even if it is waterproof, these types of tape do not have much flexibility or elasticity to them so they will rub off and not last. They will also leave a sticky residue behind.
Do bounce houses have air pockets?
You bounce house will most likely always have air seeping through the seams and built-in pockets at the top for air to flow out . This is actually an amazing feature of your bounce house as the constant stream of air flow is what keeps it so strongly inflated while so many little bodies jump all over it.
Can mice get into a bounce house?
Make sure you have a thick bag protecting your bounce house and store it in a place where mice cannot get to it. -Don’t allow shoes or sharp objects on the bounce house. Hopefully, this is a common rule for your bounce house fun for the safety of the children, but it can also protect the bounce house as well.
How To Find Cut In The Bounce House?
Before you begin the patching process, you need to find the cut or hole in the bounce house. It is easy to find large cuts, but you will have to look really hard and opt for some special tricks to find small leaks.
Steps To Patch A Bounce House
Now, you have found all the leaks in the bounce house; it is time to patch those areas. Getting a bounce house repair kit is the smartest and simplest way to solve the issue, as you will find all the tools needed to mend the cuts and tears. The following ways will help you patch all the leaks;
How To Fix The Net On A Bounce House?
Leaks are not the only problem you will face on a bounce house; torned out nets are another issue that you will often come across. However, mending the nets won’t be a huge hassle, and you would need some basic weaving skills to solve the issue.
How To Fix Tears In Seams Of A Bounce House?
You can’t fix the issue with bounce house repair spray when you get a tear in a stitch or seam. It is a severe problem that can only be solved by sewing, and importantly, it will permanently fix the tear.
