
- Use the pump to inflate the punctured inner tube.
- Locate the puncture on the inner tube by either listening for the air escaping or by placing it in water to watch for bubbles rising from the hole. ...
- Once the puncture has been located, check for any objects that may be stuck in the tube. Remove to ensure they don’t create another puncture.
- With the crayon, mark the spot where the puncture is. Release the air from the inner tube.
- Check size of hole in the inner tube to gauge correct size of patch, go large if you’re in doubt.
- Take sandpaper and gently roughen the surface around the hole.
- Apply a drop of the tyre glue and use your finger to spread it thinly over a 2cm area around the hole.
- Allow glue to dry and repeat step 7, remember to let the glue dry completely.
- Peel the backing foil from the patch, being careful not to touch the sticky adhesive surface. If there is cellophane backing on patch, this can be left on.
- Place the patch on the puncture so that the hole is in the centre of the patch. Press it firmly into place.
- Leave the patch a couple of hours for the glue to cure.
- Once the patch has adhered, give the area a dusting with chalk or talcum powder as this will help to prevent it from sticking to the inside of your tyre.
How do you fix a punctured inner tube on a bike?
Apply a patch to the inner tube if you're mending it Inner tubes can be quite expensive, and they're easy to fix so it's a good idea to mend them instead of simply replacing one and chucking the old rubber. If the puncture is not obvious, pump up the inner tube. Once inflated, it is usually easy to hear the air escaping.
How do you fix a hole in an inner tube?
Prepare the inner tube for patching Sand down the area around the hole to aid adhesion. Select an appropriately sized patch – if in doubt, err on the side of caution and use a bigger rather than smaller patch. Roughen the surface of the tube around the hole with sandpaper (usually included with any good puncture repair kit).
How long does it take to repair a punctured inner tube?
It can be daunting for the inexperienced but only takes a few minutes once you know what you’re doing. In the following guide and videos below, we’ll talk you through how to repair a punctured inner tube on either a road or mountain bike in a simple, step-by-step walkthrough guide.
How do you fix a puncture on a tire?
In your puncture repair kit, there should be a small piece of sandpaper. Use it to lightly rub around the damaged tube in the area of the hole to provide a better surface for the rubber solution to grip.

How do you fix a hole in an inner tube?
0:382:06How to Patch a Bicycle Inner Tube - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the tire push to one side place the valve of your new tube through the hole in your rim. MovingMoreWith the tire push to one side place the valve of your new tube through the hole in your rim. Moving around the wheel tuck the tube into the tire. Starting at the valve reinstall.
How do you fix an inner tube without a patch?
0:171:16How to Fix a Bike Flat without a Patch Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep 3 wrap the strap from your sunglasses. Around the hole in the tube like a tourniquet tying.MoreStep 3 wrap the strap from your sunglasses. Around the hole in the tube like a tourniquet tying. Several knots around and next to the hole to create an airtight seal.
Is it worth patching an inner tube?
Although some may disagree, it's generally not worth patching a tube unless you don't have a spare tube handy. However, patch kits are so small and light that there's no reason not to carry one unless you're counting grams. It'll come in handy the day you carry a spare tube and have two flats.
Can you patch an inner tube with duct tape?
Patching Inner Tubes with Duct Tape You can use duct tape to cover the hole and at least go down the road for a short distance. If there's no puncture repair kit in sight, use some more tape to cover up your hole until you have time to fix it properly.
Can Gorilla Glue patch a tire?
Introduction: Tire Plug: Gorilla Glue Edition Unlike traditional tire repair, "Tire Plug: Gorilla Glue Edition"eliminates the hassel of pluging a tire.
How do you make a homemade tire patch?
5:339:35DIY Cheap + Easy Trick For A Flat Tire Repair. Never Be Left Stranded ...YouTubeStart of suggested clipEnd of suggested clipNext up and what you want to do you take your rubber cement that comes with your tyre plugin kit andMoreNext up and what you want to do you take your rubber cement that comes with your tyre plugin kit and you're gonna put some on. There.
How long can you ride on a patched inner tube?
Standard glue patches last pretty much indefinitely if applied correctly. They can be a pain to apply on the trail, but I've had them last over a year. I have 5 or so of the park glueless patches on one tube, some of which have been on there for months.
Should you replace inner tube after puncture?
As long as it is a pin sized nail and not a rail road tie then you should be just fine replacing the tube and still using the tire. Just be sure the pin is not still in the tire ready to flat another tube. If its just a puncture, learn to patch the tube.
Do bike tube patches work?
0:291:43How do I fix a puncture using glueless repair patches? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use two fingers to apply even pressure and avoid the patch from moving around. And just likeMoreYou can use two fingers to apply even pressure and avoid the patch from moving around. And just like that we fixed our puncture. You can now put your inner tube back on your bike.
Can I use superglue to fix a puncture?
No. "Super glue" dries hard, and will not flex as needed when the tire flexes. It will flake off in short order. Plain old "rubber cement" (the stuff used to glue paper) is a far better choice.
Can you patch a bike tube with electric tape?
Cut a three-inch piece of electrical or duct tape. Believe it or not, materials contained in patch kits often aren't as effective as good-quality tape. Place the piece of tape over the hole, making certain the hole is in the center of the strip. Wrap the tape completely around the tube.
Can flex tape seal a tire?
1:208:29Fix A Flat Tire With Flex Tape? Will It Work? - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd get it nice and sealed there I can use like the plastic handle with scissors here to kind of rubMoreAnd get it nice and sealed there I can use like the plastic handle with scissors here to kind of rub it. On. Like that and we'll see how that does okay now go ahead and put the tube back in the tire.
Can you use super glue on inner tubes?
Can I use super glue to mend punctures? In summary, super glue cannot be utilized to patch or repair a puncture in tires or their associated inner tubes by its very nature. Cyanoacrylate gum or super blue often gets dry, brittle, and inflexible after prolonged exposure to air.
How do you patch a tire without a patch kit?
First, cut out a small piece of rubber from an old tire and insert it into the punctured hole with a screwdriver. Then, make sure to apply gorilla glue on the rubber strip before pushing it in to stick to the tire. Finally, cut out the rubber protruding out from the tire and continue with your journey.
Can I use rubber cement on tires?
Rubber cement can be used (optionally) as a plug lubricant to aid with installation. It is not required to adequately repair your tire puncture.
Can you plug an inner tube?
The processes for tubed and non-tubed tires is different, but both tires can be made rideable again (at least enough to get you home). Plugging a non-tube tire is the easier of the two. Patching a tubed tire requires you to remove the wheel, popping the bead and pulling out the tube to fix it.
How do I know what inner tube I need?
In general there are two types of valve, Presta and Shrader Valve. A Shrader valve is the same as you’ll find on a car tyre and to inflate it you s...
Why do I keep getting punctures?
If you find you're getting regular punctures, it's a good idea to check your tyres are still in good condition and appropriate for the type of ridi...
Can you fix a ripped tyre?
If the hole in the tyre is large, this may cause the inner tube to bulge through the gap, like a hernia. If this is the case, replacing the tube wi...
How to put a tyre back on a car?
Seat the tyre back into the rim. When the inner tube is all in, twist the tyre back into place, starting at the valve. Try to finish directly across from the valve as the tyre will be looser there. If it gets difficult, let a little air out of the inner tube.
What are the two types of valves on a bike?
Valve and inner tube types. There are two types of valve with bike inner tubes: Presta and Shrader. A Shrader valve is the same as you’ll find on a car tyre and to inflate it you simply have to use a pump with a compatible adapter. To deflate it you have to push a little pin found inside the valve.
How to remove a tyre from a wheel?
Pull the tyre away from the rim using the tyre levers , one at a time. If you have three levers, hook the first two under the spokes and remove some more of the tyre with the third lever. By now the tyre should be loose enough to simply run a tyre lever around the wheel rim to remove the rest of the tyre.
What to carry on a bike?
Things to carry on any ride 1 Tyre levers 2 Two (or more!) spare inner tubes 3 Patches/repair kit 4 Some bits of old tyre to reinforce big holes 5 A pump 6 A mobile phone: if all else fails, get a lift home before hypothermia sets in
How to check if a tyre is penetrating?
Run your fingers along the tyre carefully, checking for thorns or glass. Check that there are no further holes in your inner tube. Then carefully run your fingers around the inside of the tyre to check there is nothing else penetrating the tyre - if you find anything (small pieces of glass, thorns, gravel), remove it.
What happens if you rip a tyre?
Fixing a ripped tyre on your ride. If the hole in the tyre is large, this may cause the inner tube to bulge through the gap, like a hernia. If this is the case, replacing the tube will just result in another puncture. The solution is to reinforce the hole, with an old piece of tyre from the inside.
How to get air out of a puncture?
If the puncture is not obvious, pump up the inner tube. Once inflated, it is usually easy to hear the air escaping. If not, run the inner tube past your lips to sense the escaping air. Once located, roughen the area around the hole thoroughly with the emery paper in your puncture outfit.
How to repair a puncture tube?
In your puncture repair kit, there should be a small piece of sandpaper. Use it to lightly rub around the damaged tube in the area of the hole to provide a better surface for the rubber solution to grip. Next, apply the rubber solution to the tube.
How long to hold patch against tube?
I usually hold the patch against the tube for a good 30-60 seconds to make sure the whole thing is securely stuck down.
How to lift a tyre up?
Levering the first bit of the tyre off the rim is the hardest part. Let all of the air out of the inner tube ( if there’s any left, that is) and push the lever end of the tyre lever under the bead of the tyre. Then push down hard on the end of the lever and lift the tyre up.
What are some things that cyclists can puncture?
No matter how smooth your local roads, how tough your tyres, how little you ride in the rain, eventually you will puncture. It’s just one of those things. A couple of tyre levers, a small piece of sandpaper, some tube patches and rubber solution are all you need.
Why do you have to stick a tube back in a tyre?
If your puncture’s been caused by something piercing the tyre, the last thing you want is to fix the tube, stick it back in the tyre only to puncture again five minutes down the road because the piece of glass or offending item is still stuck in the tyre.
Can you remove a tyre without levers?
Some tyres can be removed without the use of levers if they’re particularly supple, or you have a very strong grip, but tyre levers just make the process easier. Once you have half of the tyre completely out of the rim, you can remove the tube. After the tube’s out, check it over to see where the hole is.
Do you need a CO2 inflator for a punctured tyre?
You may want to carry a tyre boot as well just in case the tyre is badly damaged. Needless to say, you’ll need a pump or CO2 inflator , too. And when you do puncture, you’ll need to know how to fix the punctured inner tube. Admittedly, you can just change the damaged tube for a new one but unless you have an endless supply ...
How to fix a puncture in a tyre?
Fixing a puncture: useful tips 1 When taking the tube out of the tyre, note which way the tube was around in the wheel. This will help identify the position of the hole in the tube once the position of the object in the tyre causing the puncture has been found 2 Once you’ve located the hole in your puncture, mark it with a piece of chalk (usually included with a repair kit) so you can pinpoint it accurately later 3 If you don’t have any sandpaper, you can try gently to roughen the tube by rubbing it against a stone or the road surface, but be very careful
What does it mean when a tube has a hole in the inner side?
A hole on the inner side of the tube indicates that the puncture was caused by something around the well of the rim, usually a rough edge on a spoke hole or torn rim tape if it is made of hard material.
What causes flats on a bike?
Regular or ‘point’ flats are caused by debris piercing the tread of the tyre. BikeRadar. A ‘regular’ puncture is usually caused by debris – glass, thorns, wire, nails etc. – entering the tread of the tyre and piercing the inner tube.
When taking the tube out of a tyre, what should you note?
When taking the tube out of the tyre, note which way the tube was around in the wheel. This will help identify the position of the hole in the tube once the position of the object in the tyre causing the puncture has been found
Why do tyres stick to the ground?
This is because surface water essentially acts as a lubricant, allowing anything sharp to enter the tyre more easily. Wet weather allows debris that would otherwise stay on the ground to stick to your tyre more easily too, with the rotation of the wheel slowly driving it into your tyre.
Can you leave the house without a mini pump?
Never leave the house without a mini pump! Steve Behr. While a mini pump is a great option if you’re out on the road, do yourself a favour and get a decent track-style pump for use at home – these take far less effort to use than a mini pump and will allow you to get your tyres up to much higher pressures.
Can you use glueless patch kit?
If you’re using glueless patches, you can apply them directly after cleaning the area around the hole. If you’re using pre-glued patches – such as Park’s popular GP-2 patch kit – you can now patch the hole. Thoroughly press down on the patch to ensure it’s fully in contact with the tube.
How to patch a bike tube?
I don't know if I can put a normal patch, because if the patch's edges detach even only a millimeter from the inner-tube, the hole will no longer will be covered and air will again escape. Any idea? I give my 2 ideas: 1 Take a bike patch and cut a round hole in the middle, and then patch the inner tube with it, as if it were a ring, hugging the valve by all sides. 2 Get some super glue or cement that covers the hole somehow.
How to patch a valve stem?
Draw a dot on the patch where the valve stem will be. Tape the patch to a piece of wood. Find a drill bit that is the size of the valve stem. Drill a hole in the patch at the place you marked in step 2. Remove the tape from the patch.
How long to leave vulcanising fluid on valve stem?
Buff the area on the tube, which means all around the valve stem plus the area of the cut. Use sufficient vulcanising fluid on the tube, and leave it for 5-10 minutes till its cured.
