What You Need To Know About How To Repair James Hardie
James Hardie Industries
James Hardie Industries plc. is an industrial building materials company headquartered in Ireland and listed on the Australian Securities Exchange which specialises in fibre cement products. James Hardie manufactures and develops technologies, materials and processes …
How to tell if your home has hardboard siding?
PRESSBOARD SIDING CARE & MAINTENANCE
- Watch for any major flaws. Be on the lookout for any cracked paint, missing sealant, holes, loose nails and other such problems in your hardboard siding that could lead ...
- Slope the ground away from hardboard siding. Make sure that the ground slopes away from the foundation. ...
- Keep nature away from hardboard siding. ...
How to clean your James Hardie siding?
- Always clean and rinse from the top of the siding to the bottom, so that grime gets washed away instead of spread around on the siding.
- Don’t let soap or cleansers dry on the siding. ...
- Regularly rinse out the cloth or sponge as you work, to avoid spreading any grime around on the siding.
How to properly install James Hardie siding?
Mistakes in Installing Hardie Board Siding
- There are instructions on the bag of James Hardie, but installers still store it incorrectly. ...
- The installers of Hardie Panels need to be fastened to the studs in a consistent pattern. ...
- At first glance, it seems like getting the boards together is easy. ...
- Most installers use air nailers to install HardiePlank siding. ...
How to stain hardiplank siding?
How to Stain Hardiplank Siding
- Finish the board prior to installation. To achieve the appearance of stained wood on Hardiplank, your best bet is to finish the siding before it is installed on ...
- Lay the boards out flat, wood-grained side up. Fiber-cement stain is a product that replicates the look of natural wood by pooling in the imprinted grain pattern on ...
- Dust off the boards. ...
See more
How do you repair Hardie board damage?
Cut the fiber cement siding to length (wear approved dust protection). Blind-nail the fiber cement siding in place, starting with the bottom piece. Face-nail the top piece of fiber cement siding through the old siding. Prime and paint new siding to match the old.
How do you repair Hardie board siding?
The James Hardie company, makers of HardiePlank, recommends the use of a cement patch product made of an acrylic mortar compound for patching their siding products. Acrylic mortar compound can be found at most home improvement retailers and hardware stores under various brand and trade names.
Can hardiplank be patched?
Dents, chips, cracks and other minor surface damage in Hardie® siding and trim products can be filled with cementitious patching compound.
Can you touch up Hardie board?
3:444:19ColorPlus® Touch-up Kit Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd wipe it down James Hardie does not approve caulk to touch up nail heads nail holes dents cracksMoreAnd wipe it down James Hardie does not approve caulk to touch up nail heads nail holes dents cracks or other minor surface blemishes on James Hardie color plus products.
How do you replace one piece of fiber cement siding?
3:114:42Replacing some pieces of hardboard siding with decent results - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know measure it measure the replacement. Board cutting it with a circular saw just a regularMoreYou know measure it measure the replacement. Board cutting it with a circular saw just a regular blade in here kind of a general purpose blade stuff cuts very very easily.
How do you repair cement fiber siding?
2:0414:21How to repair and replace damaged siding: Hardie board, Masonite or ...YouTubeStart of suggested clipEnd of suggested clipAny caulk that might be there underneath my pry bar and gently lift that back take a wedge stick inMoreAny caulk that might be there underneath my pry bar and gently lift that back take a wedge stick in there. And just walk.
How do you repair damaged cement board?
Use a carton knife or carbide tip tool to cut the cement board to expose a stud on either side of the damaged area. Use the knife to score and break a new piece of cement board to fit the hole. Attach the new board to the stud using corrosion-resistant screws. Predrill the holes for easier installation.
What kind of caulk do you use on Hardie board siding?
Manufacturers' Caulk and Sealant Recommendation Sheet S-100B Caulks and Sealants: James Hardie recommends the use of caulks and sealants that remain permanently flexible.
How do you fix a crack in cement board?
Use thin-set mortar to repair cracks or holes in cement boards. Step 3: Mix up a small amount of thin-set mortar following the manufacturer's instructions. Thin-set mortar typically has a working time of less than 15 minutes, so smaller batches are the way to go.
What brand of paint does James Hardie use?
If you have James Hardie fiber cement siding with any of its ColorPlus® Technology colors, Sherwin Williams can match any of those colors. That fact is a huge advantage.
How often should hardiplank be painted?
every ten to twenty yearsHardie Plank is also called fiber cement siding. While it's far heavier than aluminum, vinyl or wood, it is extremely durable and typically only needs a new paint every ten to twenty years for maintenance. It is one of the best materials and long-term solutions for protecting your home.
What was the main problem with fiber cement board siding?
Fiber Cement is Difficult to Install Cutting fiber cement siding generates respirable crystalline silica, a known human carcinogen. Inhaling too much silica can lead to silicosis, lung cancer, and COPD.
What causes hardiplank to crack?
Common Causes For Hardie Board Cracking Or Splitting Nails driven below the panel surface and directional nailing can cause cracking and splitting of fiber cement. Nailing too high or close at an edge. This can create a small crack which leads from the nail to the edge of the siding board.
How do you repair cement board?
Use a carton knife or carbide tip tool to cut the cement board to expose a stud on either side of the damaged area. Use the knife to score and break a new piece of cement board to fit the hole. Attach the new board to the stud using corrosion-resistant screws. Predrill the holes for easier installation.
Do you caulk Hardie board joints?
James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank® siding with ColorPlus® technology. James Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2).
What is the best way to clean siding and trim?
Extra care should be taken when cleaning your siding and trim using a pressure washer.
How much pressure should I use to keep siding and trim from leaking?
To minimize the chance of damaging your siding and trim use a wide fan tip, keep a minimum of 6 feet from the wall, and keep the pressure below 1500 psi. Maintaining the exterior of your home helps prevent water intrusion and is an important part of sustaining the beauty and value of your home.
What is fiber cement maintenance?
As a guide, it is recommended that normal fiber cement maintenance tasks and care include: Installing gutters and downspouts on your home —if they are not already present when you purchased the home. Cleaning out your gutters, blocked pipes, and overflows of any debris, leaves, twigs and dirt.
Can you replace James Hardie siding?
It is advised to replace the damage siding with a new section of ColorPlus® siding. If your James Hardie siding was originally painted after it was installed on your home, then check the original paint manufacturer’s recommendations for reapplication of paint.
Can James Hardie siding be filled with cementitious?
Dents, chips, cracks and other minor surface damage in James Hardie siding and trim products can be filled with cementitious patching compound. Refer to manufacturer’s recommendations for products that are compatible with fiber cement.
What Kind of Paint Can I Use on a Hardie Board?
Hardie boards are usually long-lasting and will not need fresh paint for an extended period. But for maintenance reasons, the right choice of paint and the proper application will go a long way to keep the paint fresh for almost up to twenty years.
HOW TO FIX PEELING PAINT?
As mentioned before, there could be several reasons why you're facing problems regarding the paint peeling off your exterior.
How To Repair Peeling Paint on Hardie Board? (A Step-By-Step Guide)
Since we have already discussed in length the causes of paint peeling on Hardie boards, let us take some time to devote this next bit entirely to solving this problem.
The Best Paints for Hardie Boards
Now that you know how to fix peeling paint on Hardie boards let’s get down to two of the best products to use on Hardie boards or fiber cement sidings.
What to expect before siding is installed?
What to Expect Before Construction. You can expect a dumpster and your new siding to be delivered, sometimes a day or two before the installation crew arrives. Some municipalities may require a permit for a dumpster, along with other building permits, so be sure to discuss those details with your contractor beforehand.
How long does it take to install prefinished siding?
Every house is different, but a typical tear-off and siding installation project may take between 7 to 14 days. There are many things that can extend the time such as the size of your house, whether you’re using prefinished siding or if it needs to be painted, and unexpected repairs.
How to prepare your home for construction?
These tasks can help speed up work and keep your property safe during construction. • Clear a power outlet. The crew will need access to power for their tools, so it’s helpful to have a clear outlet available (preferably one that is on a 20-amp circuit).
Why is my fiber cement siding buckling?
Buckled fiber cement siding is most likely to occur because the installer failed to give the recommended gap between the ends of the fiber cement boards and abutting vertical trim at corners, windows, doors, etc. Buckling fiber cement siding may also occur if the product was not properly nailed.
Why does my siding have algae?
Algae, fungus, moss or lichens on siding are usually due to a combination of moisture and shade on the building wall. Plants too close to the building wall, repeated wetting by sprinkler systems, or unnecessarily dense close shade tree growth are conditions that can usually be remedied.
Can fiber cement siding be sealed?
Cut ends of fiber cement siding should have been sealed using 100% acrylic latex primer or paint (Certainteed) or in some cases using an approved caulk wiped on the cut surface (see our notes on Hardieplank installation). And caulk is required at certain joints such as vertical trim at windows, doors, corners.
Can you replace cracked siding?
You can replace the damaged sections (work with care); You could also back-flash and then simply paint the cracked siding; #N#any sealant or "patch" will "work" mechanically to seal the crack but it'll be ugly when painted.
Can James Hardie siding be filled with cementitious?
Dents, chips, cracks and other minor surface damage in James Hardie siding and trim products can be filled with cementitious patching compound. Refer to manufacturer recommendations for products that are compatible with fiber cement.
How long does James Hardie siding last?
James Hardie siding is a beautiful exterior product that can last longer than 30 years in Edmonton’s harsh climate. However, to ensure that the product lasts as long as it should and looks great throughout its lifespan, it’s important that your siding contractor follows the installation instructions.
How much gap between James Hardie siding?
Hardie siding requires a minimum 2” gap from all hard surfaces like decks or rooflines, and at least 8” from any soft surfaces like grass, dirt, or gravel.
What is hardie siding made of?
By now you probably know that Hardie siding is made of fiber cement, which requires installers to take care when cutting to make sure that they don’t breathe in small sand (silica) particles. Continued exposure to these particles can lead to severe long-term health issues for workers if it isn’t managed correctly.
What are some common mistakes James Hardie makes?
1. Ugly Touch-Ups. Touch-up mistakes are by far the most common error that Edmonton’s James Hardie installers make. Because James Hardie paints and cures its siding in its factories, the sheen of the touch-up that it sends out doesn’t quite match up.
How to fix bad touch ups on siding?
Unfortunately, the only way to fix bad touch-ups on Hardie siding is to repaint the entire affected wall or section. So how do you tell if your contractor is using too much touch-up before it starts to fade? The easiest way to tell is to look at your house from multiple angles and in different light conditions.
How to tell if siding is done properly?
The easiest way to tell is to look at your house from multiple angles and in different light conditions. If you see 1” to 2” circular shiny spots, your contractor may not have done their touch-ups correctly. Another easy way to tell if your siding contractor is doing their touch-ups properly is to watch them work.
Can James Hardie nails go above the nail line?
High nails are very common from inexperienced James Hardie installers, because they think the nails can go anywhere above the nail line.
