See more
How do you fix a John Deere plastic hood?
2:559:07John Deere Hood Repair - 5213 Agricultural Repair Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a die grinder grind a v-groove along the cracks about halfway through the plastic. BecauseMoreUsing a die grinder grind a v-groove along the cracks about halfway through the plastic. Because this hood is cracked next to a mounting boss. We will grind around the base of the boss.
How do you fix a broken tractor hood?
5:4217:09Cracked John Deere Plastic Hood Repair and Restoration ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipResin you can also put some fiberglass mesh and resin across here. This is where everybody's handsMoreResin you can also put some fiberglass mesh and resin across here. This is where everybody's hands come under and grab it that's usually why this crack happens in the first. Place.
What type of plastic is John Deere hood?
polycarbonate"How do I fix my John Deere lawn tractor hood?" they ask. "It's made of 'plastic'." they say. The "plastic" from which *most* John Deere lawn tractors are made is polycarbonate. This is a very rigid plastic and, when it gets cold, it gets brittle and breaks easily.
How do you fix a fiberglass tractor hood?
4:1810:02How to Repair and Paint a Fiberglass Hood - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply the filler using a plastic applicator. This type of filler can only be applied in light coats.MoreApply the filler using a plastic applicator. This type of filler can only be applied in light coats. It's only intended for light superficial surface damage. It's not intended for any structural.
How do you restore John Deere plastic?
0:525:21How to Polish and Restore the Plastic and Metal on Your Mower, UTV and ...YouTubeStart of suggested clipEnd of suggested clipWe want to put it onto our rag rub it in really good this is going to have some soy material in itMoreWe want to put it onto our rag rub it in really good this is going to have some soy material in it that does help kind of as an abrasive to take out all the oxidation.
How do you attach a hood to a John Deere?
17:2422:00How To Replace and Reinforce a John Deere Tractor Hood - YouTubeYouTubeStart of suggested clipEnd of suggested clipI came up with two and a half from here. And 9 16 from the bottom to this edge right here and put aMoreI came up with two and a half from here. And 9 16 from the bottom to this edge right here and put a few pieces of tape in position. So once you've got a little bit on the back side applied.
How do you fix a cracked snowmobile hood?
0:413:06How to repair snowmobile hood, Artic Cat M7-video 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe have a white powdery substance that I bought the supply store and will scoop a little bit of thatMoreWe have a white powdery substance that I bought the supply store and will scoop a little bit of that out this is a two-part resin the epoxy that you mix two to one mix.
How do you take the hood off a John Deere x300?
0:081:07How to remove the hood on a John Deere riding mower ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipForward. So a little bit of side pressure it pops loose when you see you're probably at the 45MoreForward. So a little bit of side pressure it pops loose when you see you're probably at the 45 degree mark. And what has happened is the little plastic stud underneath there has come out of place.
How do you recoat fiberglass?
5:097:00How to Repair Fiberglass - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd has good adhesive properties mix the resin and a mekp catalyst according to the directions onMoreAnd has good adhesive properties mix the resin and a mekp catalyst according to the directions on the container. Brush some resin on the surface. And apply the mat.
How do you repair fiberglass?
Here's how.Drill a tiny hole at each end of the crack. This will stop the crack from extending any further.Examine the crack. ... Wipe the crack with a dry rag to make sure it's clean and dry. ... Fill the crack with a fair amount of fiberglass epoxy resin, using a plastic applicator. ... Let the epoxy dry for a day.
How do you fix a hole in fiberglass?
When you are trying to repair a small hole in fiberglass, the best type of product to use is a premium epoxy. This will insure a proper repair and will not allow for shrinking of the material and create a water tight seal. We recommend the Hawk Epoxy Kit. It contains the epoxy resin, catalyst and filler for the job.
How do you take the hood off a John Deere tractor?
0:081:07How to remove the hood on a John Deere riding mower ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipForward. So a little bit of side pressure it pops loose when you see you're probably at the 45MoreForward. So a little bit of side pressure it pops loose when you see you're probably at the 45 degree mark. And what has happened is the little plastic stud underneath there has come out of place.
How do you take the hood off a Kubota tractor?
1:518:07How To Open Your John Deere Or Kubota Tractor Hood ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo just give that a like twist there and it pops open. Now. Again even on the underside of theseMoreSo just give that a like twist there and it pops open. Now. Again even on the underside of these engine compartments here they're all going to have different a lot of them don't have these stands.
How do you take the hood off a John Deere 790 tractor?
0:122:19How-to, JOHN DEERE 790 opening the hood - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's a metal rod right here just under the emblem at the front right side pull that and it shouldMoreThere's a metal rod right here just under the emblem at the front right side pull that and it should pop open if it doesn't pull it and then pull it the front right here a lot of times they'll stick.
What does SLX stand for on John Deere hood?
In the case of this John Deere hood, the symbol “SLX” is molded in. This is not a common designation – it stands for “Sabic Lexan”. Lexan is a trade name for polycarbonate, and Sabic is the manufacturer of the polycarbonate. Most often you’ll see polycarbonate designated as “PC.”. The kit comes with Polyvance’s Book of Plastic Repair, ...
What is included in a hot air welder kit?
The kit includes a high-quality hot air welder which will enable you to make fast, strong welds with the included welding ribbons. A 200 watt airless plastic welder is also included which will allow you to embed stainless steel mesh into the plastic to reinforce your repairs.
What is the most important thing to do when welding with hot air?
The most important aspect to hot air welding is to melt both the substrate and the rod at the same time, applying a light downward pressure onto the rod as you make your pass to fuse the two plastics together. Polycarbonate will discolor and bubble slightly as you make your weld – this is normal.
