
Slide the putty knife between the top of the lower panel and the bottom of the top panel. Release two tabs by prying in a downward fashion located about 4-inches from each side. Remove the lint screen. Remove ¼ inch screws that secure the blower duct in place.
Full Answer
How do you repair a Kenmore dryer?
How do you replace the belt on a Kenmore 80 series dryer?
- Unplug your Kenmore 80 series dryer before disassembling it to replace the belt.
- Open the top panel of your Kenmore 80 series dryer.
- Locate two metal clips between the front of the dryer and the toe panel at the bottom front of the dryer.
- Loosen the two screws at the bottom of the front panel.
How to repair Kenmore dryer?
- Heating Element
- Bearing Kit
- Belt
- Drum Bearing
- Fuses
- Door Switch
- High-limit Thermostat
- Flame Sensor
- Motor
- Roller
Why is my Kenmore dryer not starting?
Kenmore Dryer Won’t Start – Troubleshoot and Diagnosis
- Incoming Power Problem. If a Kenmore dryer’s start switch button is constantly engaged but the machine won’t turn on, it may be an indication of either a defective power cord ...
- Incorrect Dryer Settings. ...
- Door is Not Properly Latched. ...
- Blown Thermal Fuse. ...
- Defective Dryer Start Switch. ...
- Belt Switch Issue. ...
- Faulty Drive Motor. ...
How to fix Kenmore Elite electric dryer not heating?
How To Fix Kenmore Dryer Not Heating Up Problem
- Clogged Vent. One of the most common causes for a Kenmore dryer that is not heating up problem could be a clogged vent.
- Clogged Lint Screen. If the lint screen is clogged, follow the manufacturer’s directions on how to remove it. ...
- Uneven Loads. Clothes won’t dry if they are not evenly distributed in the dryer. ...
- Blown Thermal Fuse. ...

How do I troubleshoot my Kenmore dryer?
1:4710:17Dryer Won't Start / Kenmore / What To Check and How To Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipThrough the thermal fuse indicating that the thermal fuse is actually bad one way that you can testMoreThrough the thermal fuse indicating that the thermal fuse is actually bad one way that you can test this it's not advised go ahead and connect these two leads with a jumper cable.
How do you fix a Kenmore dryer that won't heat?
0:245:51Electric Dryer Not Heating - TOP 5 Reasons & Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll need to go check the circuit breakers normally. There's one 30 amp double breaker or twoMoreSo you'll need to go check the circuit breakers normally. There's one 30 amp double breaker or two side-by-side 30 amp single breakers. Whether they're tripped or not we're gonna reset. Them.
What causes a Kenmore dryer not to start?
If a Kenmore dryer's start switch button is constantly engaged but the machine won't turn on, it may be an indication of either a defective power cord or a defective control panel. The most common reason for such problems is an overloaded outlet or circuit.
How do you fix a Kenmore front load dryer?
1:134:00Whirlpool Duet Sport/Kenmore HE3 Dryer Disassembly/Repair HelpYouTubeStart of suggested clipEnd of suggested clipRemove the screws at the bottom. And at the top of the front panel remove the mounting screwsMoreRemove the screws at the bottom. And at the top of the front panel remove the mounting screws located inside the door.
Why is my dryer running but not heating?
Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.
How do I fix a dryer that is not heating?
11:2621:52Dryer Not Heating and The Most Common Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo let's say your dryer is not heating or it's not turning out at all the most common problem forMoreSo let's say your dryer is not heating or it's not turning out at all the most common problem for that is a thermal fuse a thermal fuse will either look like a white long fuse it's a one-time blow
When I press the start button on my dryer nothing happens?
Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to-start switch can prevent the motor from running. Use a multimeter to check for continuity through the push-to-start switch.
How do I know if my thermal fuse is blown?
To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
Why would a dryer suddenly stop working?
A faulty or broken thermostat can make a dryer stop working. Replacing the fuse or the thermostat will allow the dryer to work again. A blown thermal fuse from overheating indicates an additional problem, such as improper ventilation.
Can I fix my dryer myself?
You can solve most problems yourself—no experience necessary! Most dryer problems can be fixed in an hour with a few basic tools and a continuity tester or multimeter—and you can do the work yourself with these simple instructions.
How do you run a diagnostic on a Kenmore dryer?
1:522:51Whirlpool, Maytag & Kenmore Dryer - Using Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipTest we hit our second button once the start button will flash. We hit that. And it goes through andMoreTest we hit our second button once the start button will flash. We hit that. And it goes through and it checks our l1 voltage l2 voltage and heater voltage and then also tells us what our airflow is.
Where is the thermal fuse on a Kenmore dryer?
0:081:27How to Replace a Kenmore Electric Dryer Thermal Fuse - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe back panel from the dryer and set it aside. Pull the wires off of the thermal fuse remove. TheMoreThe back panel from the dryer and set it aside. Pull the wires off of the thermal fuse remove. The mounting screw using a 1/4 inch nut driver. Pull the fuse off of the blower housing.
Where is the thermal fuse on a Kenmore Dryer?
0:081:27How to Replace a Kenmore Electric Dryer Thermal Fuse - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe back panel from the dryer and set it aside. Pull the wires off of the thermal fuse remove. TheMoreThe back panel from the dryer and set it aside. Pull the wires off of the thermal fuse remove. The mounting screw using a 1/4 inch nut driver. Pull the fuse off of the blower housing.
How do you check the heating element on a Kenmore Dryer?
0:081:25How to Replace a Kenmore Electric Dryer Heating Element - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe heating element in an electric dryer generates the dryers heat it's one of the first parts toMoreThe heating element in an electric dryer generates the dryers heat it's one of the first parts to check if the air in the dryer. Doesn't get warm inspect.
Can a clogged dryer vent cause no heat?
Dryer vent is clogged This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow.
My Repair & Advice Featured Story
After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse.
My Repair & Advice Featured Story
First, let me share with you that I have never done anything with a dryer besides put my clothes in it and press start. I'm a girl that will try to fix things on my own if I can learn how to do it. I can do it anyone can do it. I found out by asking questions, that I needed to purchase a multimeter and learn how to use it.
My Repair & Advice Featured Story
I used the Appliance Parts Pros d.i.y. video to get some oversight on the repair; ordered the parts (heating element, Hi-Limit T-stat and Dryer Thermal Cut-Off kit). I unplugged the electric; disconnected the exhaust duct; moved the clothes dryer so that I could remove the back sheet metal panel.
My Repair & Advice Featured Story
I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad.
My Repair & Advice Featured Story
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping.
My Repair & Advice Featured Story
Background: Roper Electric Dryer model REX6634RQ0 purchased new in early 2006 by my wife. Dryer use profile is low to moderate as it was used by only one person (working from home) from 2006 to late 2007 then moved and stored in a dry basement until mid 2009.
My Repair & Advice Featured Story
After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse.
