Kenmore washers are the gold standard, but even their efficient Model 110 can stop spinning. Solutions include replacing the drive belt or door latch, but it can take some troubleshooting. Important components such as the motor control board and drive motor may need replacement, so let’s see how you can identify and fix the problem.
Full Answer
How do I troubleshoot my Kenmore washer?
- Look for the "Pause/Cancel" button on the washer control panel.
- Press the "Pause/Cancel" button twice to cancel the wash cycle.
- Check for kinks in the water supply hose while the washer does not have power.
How to fix Kenmore washer?
Kenmore HE Washer Stuck On Sensing [SOLVED] – Let’s Fix It
- Faulty Water Inlet valve. Enough water at the right temperature is a key factor in cleaning your clothes. ...
- Defective Motor Shift Actuator. Top-load Kenmore washing machines use a motor shift actuator to switch between the WASH and SPIN cycles.
- Control Board Failure. Along with the washer shift actuator failure, there is a major problem that can occur. ...
Why is my Kenmore washer not working?
Troubleshooting a Kenmore Washing Machine Whose Spin Cycle Is Not Working Check Spin Speed. Your Kenmore washer automatically chooses a spin speed based on the cycle that you select, but you can... Check for Jammed Basket. Your washer can fail to spin if the clothes basket becomes jammed because ...
How do you reset a Kenmore high efficiency washer?
A Kenmore Elite HE3T stackable clothes washer is a high-efficiency appliance designed ... check your home’s circuit breaker or fuse box; reset the breaker or replace the fuse as necessary.
How do you reset a Kenmore washer model 110?
How to Reset a Kenmore Elite HE WasherPress the "Stop" button twice, and then press the "Power" button. Video of the Day. ... Choose a wash cycle (e.g. "Normal"), and then choose your wash options (e.g. "Hot/Cold" or "Cold/Cold").Press the "Start" button to complete the reset process and restart the washing machine.
What causes a Kenmore washer not to spin?
If the clutch is worn out, it may prevent the tub from spinning. If the clutch band kit is worn out, replace it. The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning.
How do you remove the top of a Kenmore washer model 110?
3:4513:44Kenmore Top-Load Washer Disassembly (11022932100 ...YouTubeStart of suggested clipEnd of suggested clipUsing a flathead screwdriver release. The spring clips securing the cabinet to the rear panel. TiltMoreUsing a flathead screwdriver release. The spring clips securing the cabinet to the rear panel. Tilt the cabinet toward you slide forward and remove.
How old is my Kenmore washer model 110?
Locate the serial number on a Kenmore washer made by Whirlpool. The second letter of the serial number identifies the year the machine was manufactured. For instance, “L” represents 2001, “M” means 2002 and, continuing through the alphabet, “Y” means 2009.
How do you fix a Kenmore washer that won't drain or spin?
0:086:44Washer Won't Drain or Spin: Troubleshooting VMW and Direct ...YouTubeStart of suggested clipEnd of suggested clipTurn the Machine off pull the drain hose out of the standpipe. And check for a clog at the end ofMoreTurn the Machine off pull the drain hose out of the standpipe. And check for a clog at the end of the hose. Sometimes lint or debris can build up in this area and prevent draining.
Why is my washer not spinning all the water out of my clothes?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.
How do you remove the agitator from a Kenmore washer model 110?
0:061:13Whirlpool/Kenmore Top Load Washer Replace Agitator #W10076310YouTubeStart of suggested clipEnd of suggested clipTo replace your washers agitator first remove the fabric softener dispenser and lint cap ifMoreTo replace your washers agitator first remove the fabric softener dispenser and lint cap if applicable to your model. Then use a 7/16 inch socket with a 12 inch extension to loosen the mounting bolt.
How do I troubleshoot my Kenmore washer?
0:059:20Kenmore Washer Troubleshooting - How to Find Error Codes ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipTowards you then pull upwards then push back towards the rear of the washer. This will let you pivotMoreTowards you then pull upwards then push back towards the rear of the washer. This will let you pivot the washer lid on the small metal pieces on the back of the washer.
How do you fix a Kenmore washer that is off balance?
1:0211:56Kenmore Top Load Washer Getting out of Balance (W10780048)YouTubeStart of suggested clipEnd of suggested clipBut these are the new suspension rods. And these you have to uninstall from underneath. So once youMoreBut these are the new suspension rods. And these you have to uninstall from underneath. So once you get these things out from their clips on top you're gonna pull them out from underneath.
How long do Kenmore washers last?
Kenmore washing machines have been known for their longevity. Kenmore washers can last for more than a decade. On average, Kenmore washers should last for at least 10-13 years.
What is the capacity of a Kenmore model 110 washer?
3.2 cu. ft.2 Answers. carolraden, most standard for the 110 series washer is 3.2 cu. ft. of capacity.
How long should a washing machine last?
The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that's more than eight years old, unless it's a high-end model and has a particular appeal to you.
Who makes the Kenmore 110 series?
The Kenmore 110 Series is an easy to use home Washing machine created by Kenmore. Author: Daniel Ketchum (and 5 other contributors) Create a Guide.
What is the model number of a Kenmore washing machine?
The Kenmore 110 series washing machine has been common for decades. This specific model is portable and hooks up to almost any faucet using the adapter included with purchase. Different versions will have different assembly procedures and require different parts. This page is designed for the model 110.44722401. The model number is found under the lid.
What to do if washer won't spin?
If your washer won’t spin, inspect the drive belt to determine if it is broken or loose on the pulleys. If it is, you’ll need to replace the drive belt.
What to do if your washing machine doesn't agitate?
If the washing machine doesn’t agitate, check the spin cycle. First, if the spin cycle works, the motor is operating, and the belt is fine. However, if the spin cycle isn’t working, there could be a broken or loose belt, and you should replace it.
What happens if you shut the door on a washer?
When you shut the door, the washer can begin operating. If the washer door doesn’t latch shut, the door switch will prevent the washer from working. If there is a defective or broken latch, the washer will not be able to spin or start. The door latch can fail mechanically or electrically.
Why is my washer not spinning?
If defective, the drive motor can also cause the washer not to spin. However, this is rarely the cause of the washer not spinning. Before you replace the drive motor, check for more common issues.
What is the purpose of a control board on a washing machine?
The motor control board provides power to the washing machine’s motor. If the motor control board has defects, the washer may not function properly. First, check the control board for worn-out components. To determine if you have a broken control board, check that it provides power to the motor.
Why won't my washer spin?
If your washer doesn’t spin, the motor coupling might be failing. The motor coupling connects the motor to the washing machine transmission. If you have an overloaded washer, the motor coupling will fail in order to protect the motor and the transmission.
Why does my washing machine stop spinning?
If there is a broken washing machine clutch, it can also cause the machine to stop spinning. The clutch assembly connects the transmission and the inner tub. This helps the tub to work its way up to the proper spin speed gradually. If the clutch is worn out, this could prevent the tub from spinning.
Most Common Problems
The Kenmore washing machine troubleshooting process begins with a list of symptoms. When you click on the right one, we'll take you to a page of frequent causes and help you pinpoint the problem. Then we'll have the right replacement part ready and instructions on how to make the repair.
The Right Parts for the Job
We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.
