How to Fix a Kitchenaid Refrigerator Ice Maker Not Working.
- 1. Check the temperature. Kitchenaid recommends that the freezer temperature be set to zero and the refrigerator temperature be set to 37 degrees ...
- 2. Check the water supply line.
- 3. Check the water inlet valve.
- 4. Check the water pressure.
- 5. Check for a frozen water supply tube.
Full Answer
How to troubleshoot a KitchenAid ice maker?
KitchenAid Ice Maker Not Working
- The Line. This is one of the most common issues that usually occurs when the line gets clogged with frozen water.
- Water Filter. For everyone who is still struggling with getting decent ice cubes with the KitchenAid ice maker, there are higher chances that the water filter is clogged.
- Power. ...
- Jammed Issue. ...
- Water Filter. ...
- Flushing the Water System. ...
How to reset a KitchenAid ice maker?
KitchenAid Refrigerator Ice Maker Reset Steps
- First of all make sure that the manual switch present on the ice maker is turned on.
- Now tap the plastic tab present on the door jamb. This signals the light in the fridge to turn off.
- Shut the freezer door and give it about 10 sec to reset before opening the door.
- After that press the door switch 3 times and close the door. ...
Why is my KitchenAid ice maker not making ice?
- Dispense water using the water dispenser and note the amount of water flow.
- Remove the filter. The filter is located either in the base grille or inside the refrigerator compartment.
- Dispense water with the filter removed. If the water flow noticeably increases, the filter is either clogged or incorrectly installed. ...
How to clean kitchen aid ice maker?
You can clean the ice maker by following these simple steps:
- First, turn off the machine and unplug it. ...
- Now, make sure to unscrew the draining cap located at the bottom of the storage bin or under the water pan. ...
- Next, take some cleaning solution made for the ice maker machine. ...
- If you are using the cleaner, then create a solution by pouring it into the water. ...
How do I reset my KitchenAid ice maker?
Shut the freezer door and allow it to reset for 10 seconds before opening the door. Press the door's switch three times and shut the door. Let it sit for a few seconds to reset the ice maker. This should stop the blinking lights.
Why did my KitchenAid ice maker stop working?
If your KitchenAid ice maker won't make ice the cause may be a defective water inlet valve. The water inlet valve is electric and requires adequate water pressure to function. If you have a faulty valve or there is not enough water pressure, the valve won't open and the ice maker won't fill with water.
How do I reset my KitchenAid bottom freezer ice maker?
Ice Maker Reset First, see to it that the manual switch on the unit is in the right position. Press the plastic tab on the door jamb. This signals the light to switch off. Close the freezer door and let it reset for 10 seconds prior to opening the door.
How do you disassemble a KitchenAid ice maker?
0:3215:36KitchenAid Ice Machine Disassembly – Model KUID508ESS2 - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need to move the appliance away from the wall or cabinet to uninstall the lower rear accessMoreYou will need to move the appliance away from the wall or cabinet to uninstall the lower rear access panel use a quarter inch socket or nut driver to unthread all of the screws securing the panel to
How do I fix my ice maker?
0:177:47Ice Maker Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe two top screws that hang the icemaker to the freezer sidewall. The bottom screw if there is oneMoreThe two top screws that hang the icemaker to the freezer sidewall. The bottom screw if there is one must be removed completely allowing the ice maker to be lifted from the two top screws.
Where is the ice maker switch on KitchenAid fridge?
Can you turn the ice maker off? To turn the ice maker on/off: Open the freezer door and turn off the ice maker. The On/ Off switch is located on the top right side of the freezer compartment.
Do KitchenAid refrigerators have a reset button?
Yes, KitchenAid refrigerators will have a reset button. Typically, you can find this by locating the ''water filter' or 'filter reset' button and holding them down for a few seconds.
Why is my bottom freezer not making ice?
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How do you run diagnostics on KitchenAid undercounter ice maker?
0:236:22ApplianceJunk.com - 2007 Whirlpool & KitchenAid Under-The-Counter ...YouTubeStart of suggested clipEnd of suggested clipTurn the ice maker on at the user interface. Within 10 seconds of power on press. And hold the onMoreTurn the ice maker on at the user interface. Within 10 seconds of power on press. And hold the on and clean buttons until all the LEDs begin to flash.
How do you remove the KitchenAid ice maker side by side?
0:472:48Kitchen Aid Ice maker replacement repair DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere is a locking tab located underneath the icemaker on the left side. You can depress this tabMoreThere is a locking tab located underneath the icemaker on the left side. You can depress this tab and this will allow you to pull the icemaker for giving you access to the wire harness connection.
How do you remove the ice maker on a KitchenAid French door refrigerator?
1:356:56How To: Whirlpool/KitchenAid/Maytag Icemaker Assembly WPW10190981YouTubeStart of suggested clipEnd of suggested clipAnd pull the whole assembly out for approximately halfway using the flat blade screwdriver. PressMoreAnd pull the whole assembly out for approximately halfway using the flat blade screwdriver. Press the locking tab and disconnect the wire plug. Slide out the icemaker. And the attached mechanisms.
How do you test an ice maker sensor?
0:125:05Does your Ice Level Sensor Work? This is What it is Supposed to doYouTubeStart of suggested clipEnd of suggested clipAnd whenever the IR sensor reads itself you see that solid light that's how you know if the IRMoreAnd whenever the IR sensor reads itself you see that solid light that's how you know if the IR sensor is is good if that light is flashing IR sensor is not seeing each other so if you hold that panel.
Where is the reset button on my ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
How do you reset the control panel on a KitchenAid refrigerator?
Reset power to the product: Power unit down by turning off the circuit breaker(s) or unpluging the product for 5 - 10 minutes. Power unit up by turning on the circuit breaker(s) or plugging the product back in.
How do you test an ice maker sensor?
0:125:05Does your Ice Level Sensor Work? This is What it is Supposed to doYouTubeStart of suggested clipEnd of suggested clipAnd whenever the IR sensor reads itself you see that solid light that's how you know if the IRMoreAnd whenever the IR sensor reads itself you see that solid light that's how you know if the IR sensor is is good if that light is flashing IR sensor is not seeing each other so if you hold that panel.
What happens if you have a problem with your Kitchenaid ice maker?
Water Supply Line. If there is a problem with the water supply in your KitchenAid Ice Maker, it’s going to cause problems as well. One needs to ensure that the water supply is properly connected to the other water supply (the cold ones).
How long does it take for a Kitchenaid ice maker to defrost?
There’s also a simpler fix, though it takes a bit longer. If you take out the power cord and let it rest for three to four hours , the line will defrost. Once the line is defrosted, just plug in the power cord again and you will be able to make ice through the KitchenAid ice maker.
Why does my ice maker keep popping out?
This is one of the most common issues that usually occurs when the line gets clogged with frozen water. As a result, the ice maker will either make smaller than usual cubes or there will be crescent-shaped cubes popping out. In order to fix this issue, you need to repair the line and unclog it.
What temperature does a Kitchenaid ice maker need to be?
If the temperature of the KitchenAid ice maker is higher than 10-degrees Fahrenheit, the ice cube production is going to be spotty.
What to do if water pressure is declining?
If you notice the water pressure declining considerably, it might be a wise idea to check the line first and then move on to check the water filter. Issues with either could cause these problems.
Does Kitchenaid use electricity?
Check Price on Amazon. The KitchenAid Ice Maker doesn’t even consume a lot of electricity, and it’s generally quite a handy appliance to have around the house. If you are looking for a reliable KitchenAid Ice Maker, you should definitely consider buying this machine.
When should an ice maker start working?
Once the ejector’s arm is cleaned up , the ice maker should start working properly.
How to fix ice maker that is jammed?
First, ensure that ice is not jammed in the ejector arm of the ice maker. Remove jammed ice from the ejector arm using only a plastic utensil so the ice maker is not damaged. This will likely resolve the issue. Because the ice may not be completely frozen yet, when the harvest fingers try to harvest the ice cubes, the fingers bring up icy water that attaches to the stripper. This icy water can then freeze on the stripper during the next cycle causing an ice bridge. This ice bridge will cause the harvest fingers to jam.
What happens if the ice maker is on but disconnected?
If the ice maker is on, but disconnected to water supply line, the following could happen: The ice maker will continue to try to make ice, causing a buzzing sound. A refrigerator section may to be too cold.
Was the water system flushed after filter installation or replacement?
Flush the system is needed every time the filter is changed or once the refrigerator is installed to the water supply line for the first time. Air in the water system may cause dripping at the dispenser or small/hollow ice cubes.
What causes ice to be thin?
A clogged or incorrectly installed water filter will reduce the water flow to the ice maker and could cause thin, low or no ice production.
Is the ice maker turned on?
Verify that the ice maker is turned on. If the ice maker’s water supply is not connected to water supply line, turn the ice maker off. If the ice maker is on, but disconnected to water supply line, the following could happen:
