how to repair lap siding

1. Buy Replacement Siding. Go to your favorite home improvement store and purchase replacement shiplap siding for your home. ...
2. Create Cut Line. Have someone help you and take the chalk line and create a rectangular line around the damaged section of shiplap siding.
3. Cut Out the Damaged Section of Shiplap Siding. ...
4. Measure and Cut New Siding Piece. Measure the cut out piece of siding and transfer the measurements to the new piece. ...
5. Install New Shiplap Siding. Insert the new piece of shiplap siding into the cut out area and nail with concrete covered siding nails.
Seal with Caulk. Run a bead of caulk along the edge of the newly installed shiplap siding. Don't apply too much caulk.
Sand the Edges. After the caulk is dry, use the sandpaper to sand away the rough edges and built up caulk. ...
Paint or Stain the New Siding. Paint or stain the new siding section to match the color of your home.

How do you replace lap siding?

Make your repair last

• Painting wood siding helps it last. ...
• Do not drive the nails flush or countersink them. ...
• Leave a 1/8-in. ...
• Prevent water from splashing on the siding by installing gutters or repairing leaky ones. ...
• Where siding meets a roof, it will rot if the siding touches the shingles. ...
• Consider replacing rotted areas with fiber-cement siding. ...

How to replace damaged lap siding?

How to Replace Fiber Cement Lap Siding Boards

1. Preparation. Determine the amount of the siding that needs to be replaced, and order or buy the necessary pieces.
2. Remove Damaged Lap Siding. Put on protective eyewear and a face mask. ...
3. Fix any Problems Behind the Siding. Check the area behind your siding to see if any damage has occurred there was well. ...
4. Replace Boards. ...
5. Paint. ...

How do I match old siding in need of repair?

• Contact the Manufacturer. If you know the make of your current vinyl siding, contact them about a replacement piece.
• Local Home Improvement Store. Try large stores like Lowes or Home Depot.
• Specialist Vinyl Siding Store. Contact a store online or find one near you.

How to repair damaged shiplap siding?

Steps:

1. Pull loose nails from clapboard siding.
2. Tap flat bar under siding to loosen nails.
3. Secure old siding by driving ring-shank nails down at an angle through the old nail holes.
4. Pull nails from split clapboard.
5. Grab butt edge of damaged clapboard and lift up sharply, snapping it off.
6. Use flat bar to carefully pry up the siding course above.

More items...

How do you repair wood lap siding?

0:4211:13Replacing your rotten wood siding! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you have two joints together it. Makes it easier for it to right so you don't have caulkMoreSo if you have two joints together it. Makes it easier for it to right so you don't have caulk underneath there if you do have caulk you take your razor knife and you run your razor knife.

Can you patch lap siding?

0:384:07Burleson Handyman How to patch lap siding - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe top lip goes up underneath that top piece of siding. The bottom lip is made curls roundMoreThe top lip goes up underneath that top piece of siding. The bottom lip is made curls round underneath the bottom and then you just have two nails and the sides holding the gap.

How do you repair Hardie lap siding?

8:2814:21How to repair and replace damaged siding: Hardie board, Masonite or ...YouTubeStart of suggested clipEnd of suggested clipGet a nice big caulk. Right there. And then my piece is ready to go again i just do the same processMoreGet a nice big caulk. Right there. And then my piece is ready to go again i just do the same process again this is for keeps this time. So run it up underneath the first board drop it down.

How do you replace one piece of fiber cement siding?

3:114:42Replacing some pieces of hardboard siding with decent results - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know measure it measure the replacement. Board cutting it with a circular saw just a regularMoreYou know measure it measure the replacement. Board cutting it with a circular saw just a regular blade in here kind of a general purpose blade stuff cuts very very easily.

How do you repair holes in fiber cement siding?

Use a plastic putty knife to apply the patching material to the damaged area, filling in the area and shaping the patch to match the original contours of the siding. Allow the patch to thoroughly dry and apply another thin layer of patching material if the first layer shrank during the drying process.

How do you fill holes in Hardie siding?

The installation guide for Hardie Board, which is a brand of cement board siding recommends using caulking to fill nail holes. When I've installed it I used a high-quality exterior paintable calking after smoothing the edge of the holes. Once the caulk is dry you can touch up the paint.

How do you fix fiber cement board?

2:1410:26Installing cement board on the wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipReally on the walls I'm only going about four screws four to five screws. Down the stud. You canMoreReally on the walls I'm only going about four screws four to five screws. Down the stud. You can just spread them out we'll talk about this when you get to the floor.

What kind of caulk do you use on Hardie board siding?

Manufacturers' Caulk and Sealant Recommendation Sheet S-100B Caulks and Sealants: James Hardie recommends the use of caulks and sealants that remain permanently flexible.

Why does fiber cement siding crack?

Nails driven below the panel surface and directional nailing can cause cracking and splitting of fiber cement. Nailing too high or close at an edge. This can create a small crack which leads from the nail to the edge of the siding board.

How do you caulk fiber cement siding?

0:542:14How to like a Pro: Caulking Cement Siding - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe caulking tube which we use our tool that's on the caulking gun we push it in pull it out this isMoreThe caulking tube which we use our tool that's on the caulking gun we push it in pull it out this is ready to go we insert it in the gun. Push it up where it needs to go. And we're ready to begin.

How do you fix a broken Hardie plank?

2:0910:22How To Replace Damaged Siding | THE HANDYMAN - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat I would do is I'd use this heat this notch here put it up around the nail. Put some upwardMoreWhat I would do is I'd use this heat this notch here put it up around the nail. Put some upward pressure on it. And then give it a tap like that. And then it's fully exposed.

How long does it take to repair lap siding?

We'll show you how to fill small holes, fill large holes, repair a split, and replace siding pieces. Most repairs will take less than an hour.

What is the purpose of painting exterior siding?

A generous coat of exterior paint will spruce up a home's appearance and protect the siding from weather and time. Though it requires only basic skills, a paint job (including preparing the walls, which is often more work than the actual painting) must be approached with careful planning and attacked with diligence and attention to detail. We'll walk you through both the prep and the painting process.

Can you fix holes in siding?

Holes, dents, and other damage to siding can usually be fixed quickly and inexpensively. A new generation of wood fillers, hardeners, and epoxies fill holes and firm up soft spots so they are as strong as the original wood. These small repairs can add years to the life of the siding. Boards, shingles, and panels usually can be replaced without too much trouble. Often a major re-siding can be delayed by repairing sections of siding. This chapter shows how to repair most types of siding, including stucco.

Can you patch aluminum siding?

Aluminum siding joins together much like vinyl, so it's fairly easy to patch or replace a panel. This piece shows you how to repair siding along with corner caps. Corner caps are small pieces sometimes used instead of corner posts for aluminum siding.

Can water damage siding?

A quality siding job is well-sealed, otherwise water can infiltrate and damage sheathing or the back of siding. Over time, however, seals can weaken, so it's important that you consistently check your siding's seal and replace or recaulk any damaged areas. This section shows you how to repair flashing and apply caulk.

What tool to use to cut lap siding?

An oscillating tool with a metal cutting blade is ideal for this job, but a simple hacksaw blade will also work. When the nails have been cut, the lower board can be pulled out. The vertical seams in lap siding should never align one over the other, so you may also need to remove portions of boards that are not damaged.

Where to blind nailed siding?

The new siding can be blind nailed near the top of the siding, so the row above it covers the nails ; or the siding can be face nailed near the bottom with the nails exposed. Be sure to use corrosion resistant galvanized or stainless steel siding nails.

How do I cut nails in siding?

Cut Existing Siding Nails: Cut through the nails that are holding the old siding in place. An oscillating tool with a metal cutting blade works great for this, or you can use a mini hacksaw with the blade extended beyond the end of the holder. In a pinch you can wrap duct tape around the bottom of a hacksaw blade to protect your hand, and use it to cut through the nails.

Why do you prime wood siding before painting?

Wood siding should be primed on all four sides before installing to protect it from any type of moisture penetration. Tinting the primer to match the house color will reduce the number of finish coats of paint required later.

Why do you prime wood siding?

Wood siding should be primed on all four sides before installing to protect it from any type of moisture penetration. Tinting the primer to match the house color will reduce the number of finish coats of paint required later.

When cutting siding, do you have to stagger the end joints?

Cutting Existing Siding: When crosscutting the existing siding, be sure to stagger the end joints so they aren’t aligned above each other. If the siding doesn’t have wood or plywood sheathing behind it, be sure to crosscut the damaged siding over a stud.

Can you replace wood siding with new siding?

Installing new wood siding using spacer gauges. Wood siding can rot or become damaged over time and will need to be replaced with new siding. Often only a few boards have to be replaced, requiring the existing siding to be crosscut in place with a circular saw and removed.

What causes loose siding?

Wind is often the culprit responsible for working loose a piece of aluminum or vinyl siding. In most cases, homeowners can quickly learn how to fix loose siding, especially with help from this article. You’ll probably only need to reconnect the J-shaped buttock with the top locking ridge. If you’re working with aluminum siding, take care not to bend it and watch out for sharp edges.

Where to put siding removal tool?

Fit the siding removal tool underneath the lower edge of the loose siding piece.

What Goes Wrong With Fiber Cement?

Some industry publishers dub fiber cement as a ‘100 year product’ so there really should be no need to ever have to repair it right? The truth is there is always variables with any home product that could require repair down the line, mostly having to do with faulty installation (gaps, uneven, loose from poor nailing, lack of backer flashing) but could also include rodents, collisions, extreme weather, or water damage to the underlayment.

Why does fiber cement siding come loose?

There are two main reasons that cause fiber cement siding to come loose, both of which stem from faulty installation of either missing a stud or nailing too high on the pieces. A plank that is nailed too high will start to sag because the thin top lip has started to give.

What is the gap between fiber cement siding joints?

One thing to note about gaps between joints of fiber cement siding is that they are left there on purpose. Although the material expands and contracts less than wood, best installation practices still allow for some movement and to respond to shifts in the home.

How long does fiber cement siding last?

Fiber cement siding is a highly durable product but anything installed 30-40 years on the exterior of a home is going to be vulnerable to damage at some point. Luckily, another versatile benefit of this product is that fixes are usually easy and generally inexpensive.

How to fix a plank that is pulling away from the house?

Planks that have been nailed missing the stud will start to pull away from the house. Either way, the simplest fix is to face nail the boards back into place , this time hitting the stud. If there is no stud available (such as near gable trim) and the plank is curling or rattling, it’s recommended to ‘pin back’ the board by face nailing it 3/4” to 1” from the bottom – strictly for aesthetics and not to increase wind load. Caulk can also be used to secure an angled cut or some other section where a backer is not available.

What to do before making repairs to a wood deck?

Just remember to always eliminate the underlying problem (water damage, rodent infestation, delaminated boards, etc.) before making repairs as you’ll just be running around in circles.

Can you repair cracked fiber cement siding?

There's no doubt that removing entire sections of board risks damage to corresponding areas but in many ways it's the only tried and true way of how to repair cracked fiber cement siding. If you need to repair fiber cement siding hole because of raccoons, mice, squirrels, birds, etc. there may be a way to fix the sections while they are in place.