Instructions
- Gather Your Supplies. Buy a repair coupling that matches the diameter of your sprinkler pipe. Couplings are commonly...
- Prepare the Pipe. Cut a small gap out of the broken pipe, about 1 inch wide, to make room for the compression coupling.
- Position the Slip Nuts and Washers. Remove both ends of the compression coupling. Slip one compression nut over each...
How do you fix a clogged irrigation line?
When your irrigation line becomes clogged, there are a few helpful steps that you can implement to remove the clog, repair the line, and go back to enjoying your usual water pressure levels. Identify where the clog is. — Before you can begin to repair the line, you must first identify where the clog is.
What is a broken irrigation line on a lawn?
Lawn irrigation lines are the pipes that direct water from your home's main line to the irrigation system's valves, or from valves to sprinkler heads. If the water pressure is weak from some of your irrigation system's sprinkler heads or large puddles appear on your lawn, then the problem could be due to a broken irrigation line.
How do you fix a broken sprinkler pipe?
Buy a repair coupling that matches the diameter of your sprinkler pipe. Couplings are commonly sold at home centers and irrigation supply dealers. Cutting the pipe is easy enough with a small hacksaw, but a reciprocating saw with a short, fine-tooth blade makes the job quicker.
Is your lawn irrigation pipe leaking?
Lawn irrigation is something most people install and then forget about. Leaks in these types of systems sometimes show up as puddles or geyser’s of water shooting from the ground. This article will show you how to repair lawn irrigation pipe.
How do you fix a broken irrigation line?
1:154:04How To Repair A Broken Leaking Black Plastic ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's several different types of hose clamps I use the simple ones with a little screw on top.MoreThere's several different types of hose clamps I use the simple ones with a little screw on top. Middle worm drive that kind of tightens them up.
How do you fix a broken sprinkler pipe underground?
1:4410:03How to fix an UNDERGROUND broken sprinkler pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can get a very clean cut I need to go look in my PVC bag of tricks. See. What I can find to fixMoreYou can get a very clean cut I need to go look in my PVC bag of tricks. See. What I can find to fix this connection. I'm back from sifting in my pile of tricks.
How do you fix a PVC irrigation pipe?
0:113:543 Ways to Repair PVC Irrigation Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip theMoreSo the washers go over each end of the pipe nuts go on first and then the washers. Then you slip the coupling over one section of the pipe. And then over the other tighten. The nuts.
How do you fix PVC pipe in the ground?
4:0010:44EASILY Repairing Broken PVC Pipes(Least Amount Of Digging)YouTubeStart of suggested clipEnd of suggested clipClear a little bit of soil or sand out of the way. The next thing you're going to do is take aMoreClear a little bit of soil or sand out of the way. The next thing you're going to do is take a coupling glue it onto the pipe that you cut over here push it all the way down until it meets the stop.
How do you fix a broken sprinkler pipe under concrete?
Swab one end of the pipe with PVC glue and then press a PVC coupler onto the end of the pipe. Swab the end of the exposed section of pipe that you cut from with PVC glue and press the other end of the coupler onto the pipe. This will seal the connection on one end of the concrete.
How do you fix a metal sprinkler pipe?
3:226:343/4" galvanized sprinkler pipe repair. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I will do is glue in a 1 inch by 3/4 slip bushing here I'm measuring the PVC pipe that willMoreSo what I will do is glue in a 1 inch by 3/4 slip bushing here I'm measuring the PVC pipe that will go between the tee and the galvanized pipe.
How do I know if my sprinkler pipe is broken?
1:233:21Finding leaks in your in-ground sprinkler system - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing to do is look and listen do you hear water running. Do you see water bubbling upMoreThe first thing to do is look and listen do you hear water running. Do you see water bubbling up from the ground are there any wet spots or pooling of water.
How to remove a broken pipe?
Remove the broken section of pipe as well as 4 to 5 inches of the pipe on each side of the break by cutting through the pipe with a hacksaw. Use a clean rag to dry thoroughly both sides of the remaining pipe inside and out.
How to find a leak in a sprinkler system?
1. Locate the source of the leak by turning on the water to the irrigation system and waiting for a pudd le to begin to form on the ground. The leak probably is directly below the beginning of the puddle. Alternatively, turn on water to the irrigation system, and look for weak water flow from sprinkler heads. Water will dribble instead of spray ...
Why is my lawn watering so weak?
Lawn irrigation lines are the pipes that direct water from your home's main line to the irrigation system's valves, or from valves to sprinkler heads. If the water pressure is weak from some of your irrigation system's sprinkler heads or large puddles appear on your lawn, then the problem could be due to a broken irrigation line.
Can you dig sod back in place?
Digging to the line to repair it is necessary, but dig carefully so you don’t harm the line or ruin the look of the lawn. Meticulously cut sod can be put back in place with little impact on the lawn's health or aesthetic appeal.
How to break compression nut?
Be careful to not over-tighten; it is very easy to break the compression nut if you use too much force. Turn on the water and check for leaks. If you spot seeping, tight the nuts just slightly more. Once you are confident that the joint is not leaking, fill in the excavation to bury the pipe.
How to put washers and nuts in a coupling?
Slide the Washers and Nuts into Place. While holding the coupling with one hand, first slide the compression washer, then the nut, onto each end of the coupling. Thread the nuts loosely onto the threaded ends of the fitting. Aaron Stickley.
Can you use solvent cement for sprinkler lines?
During a new installation of PVC sprinkler pipes, joints are normally completed using solvent-cement fittings. This becomes less practical, though, if you are trying to replace a broken segment of pipe when the rest of the lines are already in place.
How many times has wikihow been viewed?
To create this article, 10 people, some anonymous, worked to edit and improve it over time. This article has been viewed 49,264 times.
How long should a PVC pipe be?
Or you can buy a PVC fitting from most home improvement stores that has one pipe sliding inside an outer barrel with an O-ring inside. It will extend almost 3" in length. You may see in stores 1/2" to 2 1/2" in diameter sizes.
How to stop water from pouring out of pipe?
Clean the pipe. Some water will come pouring out at first, you could try to catch it, but it is easier to bail it out. Once the water stops coming out, clean both ends with a rag. ...
