
How to Revive Old Lead Acid Batteries
- Step 1: You Will Need.
- Step 2: Measure Battery Voltage.
- Step 3: Inspect the Cells.
- Step 4: Add Water.
- Step 5: Turn on Your PSU.
- Step 6: Testing Battery.
- Step 7: Edit: 28.04.2019. At the time i wrote this instructable i was 15, i didn't have a lot of equipment at that time...
Can You rejuvenate a lead acid battery?
To bring the battery back to life/ rejuvenate it so that it can charge/ retain a charge, the accumulated lead sulfate crystals have to be dissolved/ removed, hence reconditioning. For starters, reconditioning a lead-acid battery allows for the preservation of the function of the batteries.
How to rejuvenate a lead acid battery?
Steps for Reconditioning Lead Acid Battery
- put on safety goggles and glasses and gloves. You need to ensure that these items are chemical resistant and in excellent condition.
- Preparing the Battery. The first thing that you need to do before you begin the reconditioning is to clean the battery terminals.
- Check the battery’s voltage. ...
- Empty Your Battery. ...
- Cleaning the Cells. ...
- Reconditioning. ...
How to revive old lead acid batteries?
How to Revive or De-Sulphate a Lead Acid Battery - Elkridge, MD - Attach a battery trickle charger or a computerized smart charger to your old lead acid battery, and allow charging continuously ...
What's the procedure to desulfate a battery?
How do you desulfate a lead-acid battery with chemicals?
- Please put on the gloves and goggles and remove the battery from its current location.
- If the battery is used in a car, ensure that you park the car and then open the hood. ...
- Heat quart of distilled water to 150 degrees Fahrenheit. ...
- Measure about 7 to 8 oz. ...
See more

How do you bring a lead acid battery back to life?
Bring Dead Lead Acid Battery to Live AgainStep 1: Preparing the Battery. ... Step 2: Fill the Water Inside the Battery. ... Step 3: Mix Water With Acid and Charging. ... now pull the wasted water from the top of 3 holes by the syringe and let the battery charging. ... 39 Comments.
Can you fix a lead acid battery?
Lead acid batteries often die due to an accumulation of lead sulphate crystals on the plates inside the battery, fortunately, you can recondition your battery at home using inexpensive ingredients. A battery is effectively a small chemical plant which stores energy in its plates.
Will baking soda restore a battery?
Unfortunately, baking soda won't be able to repair or jump start a car battery—but it can definitely give it a good cleaning, which can take care of some battery issues!
How does Epsom salt revive a battery?
Replace battery cell solution – Mix 4 cups of water with 4 ounces of Epsom salt. Stir until the water is clear. Boiled water speeds up the process but isn't necessary. With the funnel, refill the cells with the new electrolyte solution.
How do you fix a battery that won't hold a charge?
Answer provided by. If jumpstarting your car battery doesn't fix your problem, your battery might be dead. But if it's not, you may be able to repair a car battery that won't hold a charge by performing a few tests, cleaning the cells, and reconditioning the battery.
Can old dead batteries be revived?
It is possible to recharge a dead battery, and depending upon the situation you are in, a dead battery is generally an easy fix, whether you are stuck in your garage and can handle it yourself or you are in the middle of nowhere and need professional, quick, and efficient service in the blink of an eye.
How do you fix a dead cell in a lead acid battery?
2:3017:01How to Revive a dead 12V Sealed Lead Acid Battery - YouTubeYouTubeStart of suggested clipEnd of suggested clipI begin by adding two milliliter of 30 percent sulfuric acid solution into each cell. Then I addMoreI begin by adding two milliliter of 30 percent sulfuric acid solution into each cell. Then I add distilled water all the way up to the top of the plate.
Can you put vinegar in a battery?
The chemical components inside the battery will react with the vinegar and cause severe harm to the battery. The battery might even fail to work when the vinegar is added; thus, you should be keen not to damage the battery with your own hands. However, vinegar is useful in cleaning corrosion on alkaline batteries.
Does putting aspirin in a battery work?
Be warned that adding aspirin will shorten the battery life, as the aspirin will react with the sulfuric acid to form acetic acid. Good for a boost, but bad for the innards of the battery.
Can you add sulfuric acid to a battery?
It's important to note that battery owners should never add sulfuric acid to their battery. During normal operation batteries will only consume water – and not sulfuric acid. When your battery's electrolyte is observed to be low, filling the battery with water will keep the battery healthy and safe for use.
How do you restore a 12V lead acid battery?
3:1117:01How to Revive a dead 12V Sealed Lead Acid Battery - YouTubeYouTubeStart of suggested clipEnd of suggested clipI begin by adding two milliliter of 30 percent sulfuric acid solution into each cell. Then I addMoreI begin by adding two milliliter of 30 percent sulfuric acid solution into each cell. Then I add distilled water all the way up to the top of the plate.
Can you fix a sulfated battery?
Reversible sulfation can often be corrected by applying an overcharge to an already fully charged battery in the form of a regulated current of about 200mA. The battery terminal voltage is allowed to rise to between 2.50 and 2.66V/cell (15 and 16V on a 12V mono block) for about 24 hours.
Can 12V battery be repaired?
It will likely require repeated repair cycles to bring a crystalized dead battery back to a working state, so don't expect it to be back-to-new after a single repair cycle. It is also important to note that not every battery can be fixed with Pulse Repair Technology.
How do you revive a car battery that won't hold a charge?
First, you need to light a fire and let it burn down to hot ashes. Then remove the filler/vent caps from the top of the battery, take the battery off the car, and place it on the hot ash. Be careful and make you it doesn't catch fire. The hot ashes should warm the battery up.
Why is sulfation bad for batteries?
There are many battery problems that stem from sulfation. It not only lowers the battery’s capacity, but also results in longer recharging times, creates high temperatures when the battery is working, and even increases the amount of corrosion inside the battery.
What happens to lead sulfate when it is discharged?
In a new or healthy battery, the lead sulfate produced is usually broken down to lead and sulfuric acid during the charging process. However, in a tired old battery, or one that has been discharged over a long time, the lead sulfate crystallizes into a solid form instead of converting back to lead and sulfuric acid.
Is sulfation normal in car batteries?
The process is known as sulfation and is quite normal in lead acid batteries. Sulfation is the major killer of car batteries. Sulfation commonly occurs in lead acid batteries that do not get enough charge. It is common in batteries in city cars with plenty of accessories that require constant load of electricity.
Does high current clean lead plates?
The high current actually cleans the lead plates and restores the battery’s charging capacity. Some companies sell anti-sulfation devices that prevent sulfation from occurring on battery terminals. This type of technology is more of preventive but does not reverse the process once it has occurred inside the battery.
Can a dead battery be brought back to life?
Oftentimes sulfation can be reversed and a dead battery can be brought back to life again. This restoration process involves the use of a special battery charger that sends a high current through the battery, breaking down the crystalline lead sulfate coat into lead and sulfuric acid.
What is the most common form of lead acid battery?
The most common form of a l ead acid battery is used in cars and trucks. Golf carts and electric cars and the like also use lead acid batteries. Essentially, every lead acid battery works the same way. They are also prone to the same type of degradation of the inner battery plates called sulphation. A sulfated battery is the most common malady of ...
How long should batteries be charged before de-sulphation?
Before going to the process of de-sulphation, the bad cells need to be identified first. Charge your batteries beforehand for at least 12 hours. After that, disconnect batteries from chargers and allow them to rest for 10 minutes. Open up all battery caps.
Do you have to wear gloves when working with lead acid batteries?
Must wear goggles and gloves while working with lead acid batteries. The electric cells and plates in an old battery must be sound and functional. If these vital components of a battery are damaged in any way, your old lead acid battery will never revive. Reply (2)
Can a dead battery be revived?
A sulfat ed battery is the most common malady of a dead battery, but as long as an used lead acid battery is mechanically sound, a sulfated battery can be revived. If you have pile of "dead" lead acid batteries out in your garage and you don't want to buy new ones for your specific project, then this article could be a good discovery ...
Step 4: Add Water
Take a syringe and fill each cell with water and look if fabric is absorbing water
Step 5: Turn on Your PSU
Now you will need to connect your multimeter to show you how much battery is drawing
Step 6: Testing Battery
Now leave your battery for 1h and hook it up on car hadlight or any 12v bulb
Step 7: Edit: 28.04.2019
At the time i wrote this instructable i was 15, i didn't have a lot of equipment at that time or knowledge.
How long to wait to make lead acid battery?
Making Electrolyte for the Lead Acid Battery: Add water to the Sulfuric acid; be very careful while making the electrolyte for the battery, after adding the water wait at least 30 minutes, so that the electrolyte can get cool. Finally, you can use the Hydrometer to check the specific gravity of the electrolyte.
What is a metal die?
These two Metal dies are used for making the Battery external 12V and GND terminals. These are available in different diameters. Purchase the one as per your requirement. Metal die 1 is used for the large Lead Acid batteries while the metal die 2 is used for the medium size Lead Acid Batteries.
What tool do you need to test electrolytes?
You should also add this to the list of must-have tools. This is the Battery Hydrometer. You will need this Hydrometer for preparing the Electrolyte for the Battery. This is used for measuring the density of the electrolyte, which is achieved by measuring the specific gravity of the electrolyte.
