
How to Fix a Leaking Delta Single Handle Kitchen Faucet
- Turn off Water to the Faucet. You cannot repair the faucet with water still flowing to it. ...
- Remove the Faucet Handle and Spout. The faucet handle is connected to the valve using a hex screw. ...
- Remove the Cam, Ball Assembly, O-rings, Seats and Springs. ...
- Install the New Faucet Parts. ...
- Install the Spout and Handle. ...
- Test the Faucet. ...
Full Answer
How do you fix a Delta faucet that is leaking?
Repair a Leaky Delta Faucet. Leaks in this type of faucet usually can be fixed with a new rubber seat and spring. However, you may need to replace the stem if the handle is stiff when turning on the faucet, if there is a leak around the handle when the faucet is on, or if replacing the seat and spring doesn’t stop the leak.
What is a Delta Faucet with two handles?
Delta bathroom and kitchen faucets with two handles often are stem-style faucets that include a seat and spring under each handle. This is different from a cartridge-style faucet, which has a stem-like cartridge but does not have seats and springs. The seat and spring sits below each stem, inside the faucet body.
How do you fix a leaky Aaron Stickley faucet?
Check for Leaking and Reinstall the Handle Aaron Stickley. Turn the water supply back on by opening the shutoff valve (under the sink) counterclockwise all the way until it stops. Check for leaking around the faucet stem. If it leaks, tighten the bonnet nut until the leaking stops; again, be careful not to overtighten.
How do you fix a loose handle on a kitchen faucet?
You may need to remove a decorative cap from the top of the handle to access the handle screw. Loosen the bonnet nut securing the faucet stem. Use tongue-and-groove pliers or an adjustable wrench to turn the nut counterclockwise. Unthread the nut completely and remove it from the stem.

How do I stop my Delta faucet from dripping one handle?
1:125:29How to repair a dripping Delta Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll need a 1/8 of an inch allen wrench to remove this set screw in the handle. This one is reallyMoreYou'll need a 1/8 of an inch allen wrench to remove this set screw in the handle. This one is really tight. So I ended up getting a longer one so I'd get some leverage.
How do you take a Delta single handle kitchen faucet apart?
1:078:56Delta Kitchen Faucet Leak Repair (Single Handle) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a double check to make sure that your water is off use a 1 8 inch hex head wrench to removeMoreThis is a double check to make sure that your water is off use a 1 8 inch hex head wrench to remove the set screw in the handle. Put the set screw in a parts pole to ensure that you will not lose.
How do I change the O rings on my Delta kitchen faucet?
1:112:57How to repair a leaky Delta faucet. - YouTubeYouTubeStart of suggested clipEnd of suggested clipClean off all the old grease. Each package comes with two o-rings slide the first one on the secondMoreClean off all the old grease. Each package comes with two o-rings slide the first one on the second one will slide right over the top of the first one.
Why is my single handle kitchen faucet leaking?
Continuous leak when faucet is off: When the faucet is off, water leaks from under the handle area. With this issue, dirt and debris have collected in the valve/cartridge which prevents the valve from properly controlling the flow of water. The valve/cartridge is located under the handle.
How can I tell what model Delta Faucet I have?
The model number on the package by the UPC code or may be found on a supply line tag. We also have an online tool to help identify the model. The model number is on all packaging, some faucets, and all installation instructions provided with your faucet. On the packaging, look near the UPC code or the top of the box.
How do you fix a Delta single handle kitchen faucet with spray hose?
0:391:39How to Replace or Upgrade a Delta® Kitchen Faucet Pull-Down Spray ...YouTubeStart of suggested clipEnd of suggested clipJust go ahead and press that down if you do and then gently unscrew the existing wand from your hoseMoreJust go ahead and press that down if you do and then gently unscrew the existing wand from your hose. We then are going to replace it with the Delta shield spray. Head.
How do you take apart a Delta kitchen faucet head?
3:338:29Delta pull down single handle faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipPick it up put about your screw and all your other parts and then you're able to pull the plungerMorePick it up put about your screw and all your other parts and then you're able to pull the plunger assembly. Out. So you just I just got a screw behind behind this little head.
Why is my Delta faucet dripping?
0:018:33Delta Faucet Dripping from Spout? How to fix it in - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this is a spring let's get started. Sometimes you can find out whether it's the hot or coldMoreAnd this is a spring let's get started. Sometimes you can find out whether it's the hot or cold faucet that's dripping by simply feeling the temperature of the drip.
Why is my Delta Faucet leaking at the base?
If the faucet leaks from the base around the bottom of the spout, this is usually caused by a worn O-ring at the bottom of the faucet body. If the faucet is leaking from the tip of the spout or aerator, then water is not being properly controlled by the lever ball or the spring-loaded rubber seals.
How do you replace a single handle faucet cartridge?
0:372:26Repairing a Leaky Single Handle Cartridge-Type Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a wrench to remove the retainer. Next pull the cartridge from your father. Now that you removeMoreUse a wrench to remove the retainer. Next pull the cartridge from your father. Now that you remove the cartridge you need to take it to your local retailer.
How do you change a washer on a single lever tap?
0:191:53Single lever mono basin - Flow cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipKey you'll need to remove either the handle prong or the red or blue insert to access the grub screwMoreKey you'll need to remove either the handle prong or the red or blue insert to access the grub screw dependent on the model variant used. And pull the handle to remove.
How do you tighten a single handle kitchen faucet?
0:003:47Tighten Loose Faucet Handle and base - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll need something like a swiss army knife or a small screwdriver. And right in the back ofMoreSo you'll need something like a swiss army knife or a small screwdriver. And right in the back of the handle. You'll find this tiny little cap and you're just going to very carefully pop it out.
How do you remove a Delta faucet without screws?
You can use an allen wrench (also called an allen key) to remove it. Once you've done that, you can typically just lift the faucet handle off. However, if it has a cartridge inside, you may need to unscrew a top piece as well to be able to remove the cartridge.
How do you remove the U bracket from a kitchen faucet?
0:572:09Removing kitchen faucet with a U shaped brace under the sinkYouTubeStart of suggested clipEnd of suggested clipAnd you know down here is going to be underneath the sink. So anyway you're going to have toMoreAnd you know down here is going to be underneath the sink. So anyway you're going to have to unloosen. That guy and this little nut right here. And then it will pull right out from the top.
How to remove faucet arm from upright shaft?
Gently remove the faucet arm from the upright shaft by pulling upward on it while rotating it.
How to check for leaks in water valves?
Turn on the water at the valves and check for leaks. Start out with the water on cold and on with about half the maximum pressure. If things look OK with the half pressure then turn the cold water on all the way. Again, check for leaks. Once you're sure things are OK, turn on the hot water. ...
How to remove a swivel aerator?
Step 1: Remove old end, aerator (looks like a cap with a little screen), or previous swivel that broke and part is still there; carefully clean the threads. Step 2: Use one layer of Teflon tape around the outer threads. Converter first, then swivel. Hand tighten to be very snug, and do not wrench.
How to fix Allen wrench that won't remove?
Spray it with PB Blaster and let set, then spray again. Make sure the Allen wrench is secure and turn outwards to the left. If you still can't remove it, then replace it.
How to remove chrome dome?
Remove the chrome-dome by turning counter-clockwise. You may need to use Channel-Lock pliers to get things moving. Set aside.
How to remove a golf ball from a socket?
Gently remove the ball. Please note the orientation of the ball, cut into one side of the ball is a slot that rides on a stud inside the socket.
Where to get replacement water cartridges?
You can get the replacement cartridge from any big box hardware store.
Why does my faucet leak?
When one of these faucets starts to leak, it's usually because one or both of the gaskets or springs in the valve seat are worn out. You usually can find a repair kit for your model at the hardware store, and if not, a universal repair kit often works. In some cases, the ball itself is causing the leak. If you have to replace it, you need the one ...
How to get traction on faucet?
Put on a rubber glove to increase traction, grip the collar on the top of faucet body and turn it counterclockwise. If it won't turn, wrap the glove around the collar and use adjustable pliers to turn it.
How to put springs in valve seat?
Put the new springs inside the new gaskets and drop the assemblies into the holes in the valve seat. An easy way to place them is to fit them around the tip of a screwdriver, use the screwdriver to push them into place, then hold them with your finger while you remove the screwdriver.
How to fix a cracked golf ball?
Inspect the ball. If it is full of mineral deposits that may be preventing the gaskets from sealing, chip them off with the screwdriver. You also can immerse the ball in white vinegar overnight to dissolve the deposits. If the ball is cracked or chipped, replace it with a new one.
What is a delta faucet?
Delta bathroom and kitchen faucets with two handles often are stem-style faucets that include a neoprene valve seat and spring that fits into the faucet below a cartridge-like insert stem. This is different from a true cartridge-style faucet, which closely resembles a stem faucet but does not have valve seats and springs.
How to tell if a faucet is leaking?
Determine Which Side Is Leaking. Place your hand under the drip from the faucet. If the water is warm, the leak is most likely on the hot side of the faucet. If the water is cold, the leak is most likely on the cold side. This tells you which is the better side to fix first, but it's possible that both sides are leaking in any case.
How to remove valve seat and spring?
Remove the seat and spring by inserting a small screwdriver or Allen wrench into the hole of the seat and pulling up both parts together. Note the spring's orientation inside the valve seat. The spring should be slightly larger in diameter at the bottom than at the top—where it fits into the seat.
How to replace a valve stem?
If desired, you can also replace the O-ring (which is sometimes included with stem-and-spring kits) or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing. Push the stem all the way down until it stops.
Where is the valve seat on a faucet?
Look inside the stem housing and locate the neoprene valve seat sitting in a hole at the bottom of the faucet housing. The valve seat is a small, black, rubber cap with a hole in the top. Sitting inside and below the seat is a small metal spring.
What to do if there is no water shut off valve?
If there are no shutoff valves under the sink, turn off the water to the entire house at the home's main shutoff valve, then turn on both sides of the faucet to relieve pressure in the supply lines.
Can you reinstall a faucet stem?
Note the position of the stem before removing it. You must reinstall it in exactly the same position for the faucet to work properly. Stems usually have one or more tabs that fit into notches in the stem housing to help you align the stem, but you can still get the stem backward. It might be helpful to take a photo of the stem for reference.
