
How to Repair Led Bulb
- Remove the Top Cover. Remove the top cover (diffuser) then desolder two wires of ac mains from the board.
- More Details in Video
- Check All Led. Set your multimeter to continuity mode then place your positive lead to positive side of the led and negative lead to negative side of the ...
- Remove the Led. Desolder the led carefully.
- Take a New Led
- Solder New Led
- Replace the Capacitor. In the backside you can see two capacitors one is electrolytic and another one is polyester capacitor.
- Did you make this project? Share it with us! We have a be nice policy. Please be positive and constructive.
How to troubleshoot your LED lighting system?
Method 2 Method 2 of 2: Testing with a Coin Cell Battery
- Use a coin cell battery to test your LED without burning it out. ...
- Purchase a corresponding coin cell battery holder with leads. Buy one that is made to hold the type of coin cell battery (e.g., a CR2025) you'll be testing with.
- Connect the black lead to the cathode and the red lead to the anode. ...
- Wait for the LED to light up. ...
How do you fix a LED light?
How to replace the fuse:
- Open the plug’s latch with a small screwdriver (any that you’ve collected from last year’s luxury Christmas crackers would work perfectly!)
- Use a fuse tester to figure out which is the one causing the problem
- Carefully take out the faulty fuse and replace it with the new one
- Screw the latch back onto the plug and you should be good to go!
What are the problems with LED lighting?
- LED lights do not work
- Frequent LED defects LED lamps faulty after a short time LED ceiling light does not work LED lamps go on and off Integrated LED defective LED strip no longer works
- Troubleshooting guide Checklist for external faults Operation on dimmer? Operation on transformer? Operation on motion detector? ...
- Conclusion
How to fix LED light strips not working?
Troubleshooting Tips For Monster LED Light Strip Remote Not Working
- Try replacing the batteries. This tip applies more to those of you who have been using your LED strips for a while and have only noticed problems recently.
- Pair the remote again. Like with any smart device, these LED lights have a habit of occasionally un-pairing themselves from the remote.
- Perform a factory default. ...
- Your remote may just be faulty. ...

Can LED lights be repaired?
A great benefit to LED bulbs is you can repair almost everything. Premature burnouts can be caused by poor component quality, LED overheating, and voltage jumps. The good news is that you don't have to have a lot of experience to handle the repair and the cost is significantly less than the price of a new bulb.
How do you fix a non working LED?
To troubleshoot, try the following steps:1) Confirm that your power supply's voltage and current rating are compatible with your LED strip. ... 2) Confirm that your power supply is working correctly. ... 3) Check and isolate other accessories on the same circuit. ... 4) Check for any visible loose connections.More items...
Why are my LED lights not working?
The reasons for this can vary considerably from the power source to the bulb itself. Reasons often include a faulty power supply, loose connections, a faulty circuit design, or even damage due to water ingress caused by rain.
How do you fix an LED circuit?
How to Repair LED Light CircuitsStep 1: Identify the LD Light That Doesn't Work. Identify broken LEDs. ... Step 2: Remove the Broken LEDs. Remove the broken LEDs. ... Step 3: Replace the LEDs. Replace the LEDs with lights of similar voltage. ... Step 4: Connect Replacement Lamps. ... Step 5: Finish the Fix for Your LED Lights.
Why is half of my LED lights not working?
But the answer is simply that one colour of the RGB/W LEDs is not working within that section and needs replacing. This can be caused by static-electricity damage, or bending and twisting the strip too much, or being trod on, damaged in transit, a cheap poor-quality strip, or dry solder joints.
Do LED lights burn out?
Unlike incandescent light bulbs, LEDs don't produce light using heat. This is part of what makes them so energy efficient. The downside is that their components can be sensitive to overheating, which can cause them to burn out prematurely.
Why do LED lights go out?
The most common reasons for LED blowing out are high voltage, bad contacts, use of incompatible dimmer switch, or recessed lighting. Other causes include overheating due to not using the right fixtures, or simply a bad batch of lightbulbs!
How do you reset LED lights?
To begin with, make sure that your LED light is plugged into an outlet. Next, press and hold the button on top of the power cord for at least 10 seconds. After this time has elapsed, release the button and wait approximately one minute for it to turn off automatically before unplugging it from its outlet.
What are the 3 wires on LED lights?
This means marker light, running light, brake light or blinker. In this case one of the wires will be ground (-) and the other is positive(+). Generally a white and a black wire will be provided. The white will normally be the ground(-) and the black will be the positive(+).
How do you wire LED lights?
0:498:43simple wire connections and led light wiring - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut there's always going to be subtle differences in the wires. This one for example these two clearMoreBut there's always going to be subtle differences in the wires. This one for example these two clear wires one of the wires is silver. One of the wires is a copper color.
What voltage is used for LED lights?
between 1.8 and 3.3 voltsTypically, the forward voltage of an LED is between 1.8 and 3.3 volts. It varies by the color of the LED. A red LED typically drops around 1.7 to 2.0 volts, but since both voltage drop and light frequency increase with band gap, a blue LED may drop around 3 to 3.3 volts.
Why is only one of my LED lights working?
LED strip lights are the go-to lights for straight lines, right angle corners, and subtle under lighting....Troubleshooting LED Strip Lights.IssuePossible CauseSolutionWon't Light Up (Hardwire)Loose wires; too much,insulationCheck wire connections; make sure insulation is stripped at least half an inch on the ends8 more rows•Sep 17, 2017
How do you reset LED lights?
To begin with, make sure that your LED light is plugged into an outlet. Next, press and hold the button on top of the power cord for at least 10 seconds. After this time has elapsed, release the button and wait approximately one minute for it to turn off automatically before unplugging it from its outlet.
Do LED lights fuse?
Your LED bulb doesn't need a fuse, doesn't have one, so no need to wonder if it has one. it won't work any more, other than that, it would be hard to tell unless you yook it to labratory to check to see if the diode is fused, you can use a multimeter to see if it has current flow in noth directions.
Why are only half of my LED string lights working?
If half a strand is working and the other half is not, you probably have a loose or broken bulb. Start with the first unlit bulb and work your way down, wiggling them to check for looseness. If it flickers, that's your cue to replace it.
How to remove LED light from a light fixture?
Pull out the first light that is marked with tape from the light fixture. Grasp the LED above the plastic covering and pull it until it releases from the fixture.
How to put LED light in socket?
Insert the plastic and metal end of the LED into the socket you pulled it out of until it is firmly in place. The plastic covering of the lamp should be pointing away from the socket.
What is an LED light?
LED stands for light emitting diode and refers to a lighting element that is purer and stronger than regular incandescent light. LED lights are commonly found in long strings of lights used at Christmas and other holidays for decoration. You may find that some LEDs stop working, and this causes many people to dispose of the entire string.
How to remove broken LEDs?
Remove the broken LEDs. You may need a soldering iron to do this, depending on how the LEDs are connected to the wire. In commercial LED light circuits, there may be sockets for each individual lamp, and you can simply pull them out. Note the polarity of the LEDs you remove. The polarity is determined by the differing lengths of the connectors coming from the base of the bulb. The shorter wire is the cathode, the negative charge. Remember which side this is on; the socket should be cut to suit the differing lengths.
Can you replace LED bulbs with a similar voltage?
Replace the LEDs with lights of similar voltage. LEDs do not need to be matched in voltage by a common and exact resistance value, just a general one. This makes replacing bulbs easier, because you can identify suitable LEDs by their color. There are two general groups of LED light voltage: those around 3.2V are white, blue or green, and those around 2V are red, orange or yellow. Your LED circuit is liable to be made up of one of those groups of colors.
How to test if LED is faulty?
In some cases, however, the LED may look undamaged. Then you can test and find a faulty LED using a multimeter. Most of modern multimeters have a diode test function. The test procedure is as follows: touch the anode with the red probe and the cathode with the black one. The working diode will light. If you change the probe polarity, the meter will display “1” and the diode won’t light. Neither will a faulty diode light during the test.
How to take off old LED lights?
Or you may do it with a self-made simple analogue – a copper conductor twisted around the soldering iron tip.
How does a bulb work?
The bulb operation principle is rather simple: AC current is provided from electricity line to the driver through contact wires, where it becomes DC and runs through LEDs that transforms it into light. The heat is withdrawn using a board containing LEDs and a heatsink.
What is LED bulb?
LED bulb operation is based on the abilities of some materials to emit light under certain conditions. The working element of the bulb, a light emitting diode is a semiconductor device that emits incoherent light when electric current runs through it. LEDs emit light only if you use DC current.
Why won't my LED work?
If one of diodes is dead, the rest won’t work. The most common failure reason is LED burning out (in most cases only one of them). However, sometimes several LEDs fail at the same time.
What is LED driver?
Driver. This is an electronic circuit diagram designed for transducing AC current into DC current of a required value. Excessive current leads to LED burnout. A quality driver ensures bulb operation during voltage jumps and LED operation with no pulsation. There are a lot of circuit designs for LED drivers. We demonstrate only a couple of them: There are simple drivers where voltage is limited by a resistor or capacitor, as well as more advanced drivers using microchips. This type of drivers not only limits voltage but also ensures the optimal power consumption and performs protection functions. Drivers with microchips are more modern and efficient but more difficult to produce and, therefore, more expensive.
Where is the driver located in a quality bulb?
The driver in quality bulbs should be a separate PCB and be located in the bulb cap. Each manufacturer has a unique driver circuit design, so there are no standard repair recommendations. You should apply an individual approach here.
How to test if LED chip is faulty?
To test the Failed chip, You simply plug in your LED panel and short each individual LED chip. Shorting a Failed LED chip will cause board to start glowing sans the faulty chip. Other Safer method is to use a small 3v Power source (Like 2x AA batteries) and hook up Thin probles to the output.
What happens if you short out an LED panel?
If all faulty chips have been shorted out, rest of the panel should glow right up. Usually shorting 2~3 chips over the entire count of LED chips will have no detrimental effect. Because the LED panel is wired in series, it will keep the current same across all chips. Your Panel wattage will decrease slightly.
What voltage do LED chips have?
Now the way these LED chips are laid out are usually very simple. All the LEDs have forward voltage of about 3.2V and are connected in Series. Chip boad failures means its just one or two LEDs have failed, causing entire board to not glow.
What was the name of the lamp that replaced old inefficient incandescent bulbs?
Old and inefficient Incandescent lamps were replaced by Newer CFLs. Then CFLs gave way to LED lamps.
How many components are in an LED panel?
An LED panel is made in 2 components.
Can you short chips to replace them?
Here you can try to replace the Faulty chips. But that needs very precise soldering skills along with a reflow station. You can also simply short the said chips and it will fix your rest of panel.
Introduction
If your LED light strips are malfunctioning, then this guide may be what you need. Light strips malfunction when there is a faulty connection or wiring between two sections of the strips. These faulty connections can hinder the power flow and deactivate other working strips that are connected to the faulty strip.
Step 1 How to Repair LED Strip Lights
Find the spot where the lights stop working and where there are four connections labeled in descending order, "12V, R, G, B" with a scissor "cut here" marking and a copper colored backing.
Step 2
With a scissor, cut along the "cut here" line, separating the faulty strip from the working strip.
Step 3
Align the new strip next to the working strip and keep them steady. Look at the four connections like a mirror image. R to R, G to G, and so on and so forth. Apply solder in any order for all four connections. Make sure solder is secured and steady.
Step 4
A solder and soldering iron are fairly common and easy to acquire at a hardware store. Extra length of lights may be left over from initial use, use these first before buying more in order to lower costs. In order to put the lights back where they originally were, some form of an adhesive agent may need to be utilized.
