Steps to Take Before Calling a Repairman to Fix Your Maytag Bravos Washer Step One: Check the Plug This may sound silly, but check that you firmly plug in your washer. Better yet, plug your washer straight into a wall socket and not into an extension cord.
Full Answer
Why won’t my Maytag Bravos wash Lint away?
Top-loading high-efficiency washers, like the Maytag Bravos, use much less water and that can result in lint not being washed away as easily as it is with a standard washer that uses a high-volume of water. It is helpful to run a cleaning cycle each month to flush away any lint residue in the washer. Use the Washer Correctly
How do I clean the filter on my Maytag Bravos washer?
To clean the pump filter, follow the directions in your washer manual to access the water pump. You may find lots of lint, coins, buttons, or even a sock that is causing a slow drain and leaving lint on your clothes. Problem With Maytag Bravos Fabric Softener Dispenser
Are Maytag Bravos belt driven washers?
You should note that in the newer 2010 washing machine line-up, some washer models branded Maytag Bravos do not have the same mechanical design, even though cosmetically they can look almost identical. They are Belt Driven Washer Models. This guide is for the magnetically “stator drive” washing machine models. Sale! Sale!
What is a recirculation pump on a Maytag Bravos washer?
The recirculation pump is the key to the Maytag Bravos water sipping efficiency. Instead of completely filling the washing machine’s tub like most top loading washing machines, only enough water is added to cover the washer’s wash plate and float the inner tub allowing it to lift off the basket hub .
Why is my Maytag Bravos washer not spinning?
One of the most common reasons a washing machine won't spin is an unbalanced wash load. During a wash cycle, larger, heavier items can clump on one side of the machine, causing an imbalance that affects the spin cycle. Overloading the washtub with too many items can also cause an imbalance that prohibits spinning.
Does a Maytag Bravos washer have a reset button?
How to reset Maytag Bravos washer- step by step. Turn the Cycle Selector knob counterclockwise or left (all the way around) once. Next, turn the knob clockwise (right) – Go three clicks clockwise (count one…
How do you run diagnostics on a Maytag Bravos washer?
Console & Indicator Diagnostic Test ModeThe washing machine should be in standby (off) mode.Press and release the following buttons within 4 seconds. ... if successful "dt" should display on the washing machines indicator.Whithin 5 seconds press "Start" all indicator lights should come on and 88 should be displayed.More items...
Why is my Maytag washer not draining or spinning?
A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.
How do you troubleshoot a Maytag washer?
14:0516:06Maytag Washer Won't Spin - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's going to start flashing all the lights sequentially. And it's going to take about three to fourMoreIt's going to start flashing all the lights sequentially. And it's going to take about three to four minutes to reset. Make sure that the washing. Machine is plugged in.
How do you reset the sensor on a Maytag washer?
Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.
How do you run a diagnostics and read error code on a Maytag washer?
0:045:38How to Run Diagnostics and Read Error Codes on a Maytag WasherYouTubeStart of suggested clipEnd of suggested clipThen it's three ticks to the right one tick to the left and one tick to the right and you have to beMoreThen it's three ticks to the right one tick to the left and one tick to the right and you have to be pretty precise or your timing. Or it won't engage. And then when it engages the lights flash.
What are the error codes on a Maytag washer?
Error Codes in my Maytag Front Load WasherError CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.7 more rows•Jun 16, 2020
How do I force my Maytag Bravos washer to drain?
0:001:29How to ONLY DRAIN on Maytag Bravos XL washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you got to do is put it on rinse and spin. Come over here. Hit the extra rinse button toMoreSo what you got to do is put it on rinse and spin. Come over here. Hit the extra rinse button to turn that light off i put mine on maximum extract tap the spin speed to change it.
What causes a washing machine not to drain and spin?
If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do you unclog a Maytag drain pump?
2:105:31How to UNCLOG Maytag washing machine DRAIN HOSE - YouTubeYouTubeStart of suggested clipEnd of suggested clipProperly. So let's go ahead and remove all that crud from the drain hose. And see if that fits the.MoreProperly. So let's go ahead and remove all that crud from the drain hose. And see if that fits the. Issue. And it's coming out pretty good as you can see that's a lot of water.
Why is my Maytag washer not turning on?
If your Maytag washer will not turn on, start by checking the incoming power supply to the appliance. Ensure that there are no blown fuses or tripped circuit breakers. Then, clean any corroded contact pads that are exposed underneath the user interface.
How do you reset the lid lock on a Maytag Bravos washer?
Alternative reset procedure 2 (this works for some Maytag Bravos XL washer series models)Rotate the dial(Cycle Selector knob) till it is at 12 Oclock position(turn dial 1 counter-clockwise -or right- full turn until you're back to 12)You then rotate the dial three(3) turns clockwise(right).More items...
How do you recalibrate a Bravos XL washer?
0:362:00Reset and recalibrate Maytag Bravos X washing machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipI. Don't know if this will work on any other Maytag machines. But it might so you can always try it.MoreI. Don't know if this will work on any other Maytag machines. But it might so you can always try it. So what he said was you always make sure that the drum is empty. When you recalibrate it. And if
How do you bypass the lid lock on a Maytag Bravos washer?
1:324:13How to bypass the lid lock on a Maytag or Whirlpool washerYouTubeStart of suggested clipEnd of suggested clipYou slip it right over the top right there. And that's all you need to do.MoreYou slip it right over the top right there. And that's all you need to do.
Who makes Bravos washers?
The Maytag Bravos Washer is one of 3 cosmetically different versions of the same appliance that was developed by the New Zealand appliance company, Fisher & Paykel.
How does a Maytag washer drive work?
The drive motor on the Maytag Bravos washing machines is two part system made of a stator which generates a rotating magnetic field and a rotor with strong permanent magnets embedded around it’s inner wall allowing it to levitate over the stator. When the control board energizes the fixed position stator the rotor begins to rotate, attempting to equalize in the moving magnetic field. This style of motor operates with almost zero mechanical friction, and can accelerate, stop, and reverse direction faster than you can say, “mama needs a new washer”.
How to remove impeller from washing machine?
Note: The Impeller or agitator can be removed from the washing machine by pulling the top cap off of the impeller or agitator and removing the 7/16″ bolt that is hidden underneath. This will allow you to examine and replace the agitator roller cams or lift the inner wash basket out to access the outer tub, tub sump, and lint filter for cleaning.
How many revolutions per minute does a washer spin?
Instead this washer uses a magnetic DC stator motor to operate either the impeller or agitator for the wash portion of the cycle (depending on the washer model) then during the spin cycle, the washer’s motor spins the inner tub between 800 and 1100 Revolutions per minute (RPM) without the use of a transmission or clutch.
How does an energy saving washer work?
Instead this washer uses a magnetic DC stator motor to operate either the impeller or agitator for the wash portion of the cycle (depending on the washer model) then during the spin cycle, the washer’s motor spins the inner tub between 800 and 1100 Revolutions per minute (RPM) without the use of a transmission or clutch. It’s like a magnetic bullet train to Cleansville.
Can you use bleach in a washing machine?
Even though your washing machine may have a bleach dispenser that doesn’t mean you must use it ! Bleach and bleach vapors greatly contribute to washing machine rust and corrosion. If you want your washer to last as long as possible use a plastic tub or something similar to bleach clothing, then rinse with cold water to avoid bleach vapors.
Is an impeller washer good for cleaning?
However, impeller models are probably best used in light duty cleaning situations. If you are an auto mechanic or farmer you may want to buy an agitator model.
How many revolutions per minute does a washer spin?
Instead this washer uses a magnetic DC stator motor to operate either the impeller or agitator for the wash portion of the cycle (depending on the washer model) then during the spin cycle, the washer's motor spins the inner tub between 800 and 1100 Revolutions per minute (RPM) without the use of a transmission or clutch.
How does an energy saving washer work?
Instead this washer uses a magnetic DC stator motor to operate either the impeller or agitator for the wash portion of the cycle (depending on the washer model) then during the spin cycle, the washer's motor spins the inner tub between 800 and 1100 Revolutions per minute (RPM) without the use of a transmission or clutch. It's like a magnetic bullet train to Cleansville.
Can you use bleach in a washing machine?
Even though your washing machine may have a bleach dispenser that doesn't mean you must use it ! Bleach and bleach vapors greatly contribute to washing machine rust and corrosion. If you want your washer to last as long as possible use a plastic tub or something similar to bleach clothing, then rinse with cold water to avoid bleach vapors.
Can fitted sheets be washed?
Solution…don't wash fitted sheets with heavy items like towels or blankets, and stay close while the cycle is active so you can stop the cycle and readjust the load if necessary. As a general rule towels should only be washed with other towels and heavy items that can be properly balanced. If you wash a bunch of shirts with on big towel the load will go off balance almost every time.
Is an impeller washer good for cleaning?
However, impeller models are probably best used in light duty cleaning situations. If you are an auto mechanic or farmer you may want to buy an agitator model.
What is a Maytag washer?
Share. Email. Courtesy of Maytag. Maytag is a familiar and popular name brand of washers and dryers. The Maytag line has been around for more than one hundred years with the first washer introduced to the market in 1907.
How to clean a dishwasher with white vinegar?
Heat the vinegar in the microwave until it is very hot but not boiling. Dip an old toothbrush into the heated vinegar and give the dispenser a good scrubbing. It is also helpful after the scrubbing to fill the dispenser with the warm distilled white vinegar and let the empty washer run through a hot wash cycle.
Why is my laundry dispenser not working?
If dispensers will not work correctly is often a problem with the water flow into the unit. Detergent, bleach, and fabric softener are dispensed at the proper time in the laundry cycle by a burst of water that flushes out the dispenser cup. The water lines could be kinked or clogged with residue. It is also possible that the solenoid that controls water flow is not functioning correctly. To help you check the solenoid, water lines, and remove the unit for cleaning, consult the user/repair manual .
How to clean a washer with rubbing alcohol?
Begin by cleaning the switch contact points on the lid and the body of the washer with a cotton swab dipped in rubbing alcohol to remove any dirt and lint build-up.
How to clean a sanitizer dispenser?
If the dispenser is removable, fill a sink with hot water and allow the dispenser to soak for at least 30 minutes. Use a small soft-bristled bottle brush to clean every opening. If the dispenser is not removable, you can still give it a good cleaning using distilled white vinegar.
Can you use too much detergent in a washer?
Using too much detergent leaves a residue on clothes that is sticky enough to hold onto lint and hair. No more than two teaspoons of high-efficiency detergent should be used per load of laundry.
Can Bravos washers continue after wash cycle?
Maytag Bravos washer will not continue to the next cycle after the wash cycle.
Significance
Example
Preparation
- Begin by cleaning the switch contact points on the lid and the body of the washer with a cotton swab dipped in rubbing alcohol to remove any dirt and lint build-up. If this does not solve the problem, you will need to replace the switch. Door switches are inexpensive parts and easy to replace. If you need a user or repair manual, you can find it here.
Operation
- Older washers had a removable lint filter that could be cleaned manually. Today's washers have a built-in lint filter but it cannot be accessed easily for cleaning. Top-loading high-efficiency washers, like the Maytag Bravos, use much less water and that can result in lint not being washed away as easily as it is with a standard washer that uses a high-volume of water. It is helpful to ru…
Safety
- Excess lint is especially problematic if the HE washer is ever overloaded or if too much detergent is used. Using too much detergent leaves a residue on clothes that is sticky enough to hold onto lint and hair. No more than two teaspoons of high-efficiency detergent should be used per load of laundry.
Use
- A great tip to help reduce and remove lint is to add one cup of distilled white vinegar to the rinse cycle to help the fibers relax and better release lint and pet hair. The vinegar can be added to the fabric softener dispenser for easy use. Do not add additional fabric softener.
Issues
- The most common reason that a fabric softener dispenser will not work correctly is a problem with the water flow into the dispenser. Detergent, bleach, and fabric softener are dispensed at the proper time in the laundry cycle by a burst of water that flushes out the dispenser cup. The water lines could be kinked or clogged with residue. It is also possible that the solenoid that controls …
Prevention
- If the dispenser is not removable, you can still give it a good cleaning using distilled white vinegar. Heat the vinegar in the microwave until it is very hot but not boiling. Dip an old toothbrush into the heated vinegar and give the dispenser a good scrubbing. It is also helpful after the scrubbing to fill the dispenser with the warm distilled wh...
Risks
- The problem may be worse due to the age of your fabric softener. Commercial fabric softeners can separate and thicken over time due to temperature changes. Be sure to give the bottle a good shake before each use. It may also be helpful to use 50 percent fabric softener and 50 percent water each time when you fill the dispenser.