How to fix:
- First, locate the assembly inside the washer that houses that board.
- Then, open the wire covers to remove all of the different electrical connectors attached to the main control board.
- That will make it possible to remove the old board.
- Next, install the new control board by first reconnecting all electrical wiring the same way as before.
How much should you pay for Maytag washer repair?
Appliance repair costs $172 on average, with a typical range of $105 and $240. This includes parts and $50 to $150 per hour for professional service. Although this range includes most common appliance problems, there are several factors that may affect the total. If the unit is more than 10 years old, runs on natural gas or cost $5,000 when you ...
How do you troubleshoot a Maytag washer?
- Assess the load.
- Determine whether the washer is plugged into the electrical outlet.
- Remove any kinks from the drain hose.
- Close the washer's lid securely to add pressure to the lid switch.
- Avoid overcrowding your load; an unbalanced, heavy load can contribute to excessive water fill that can leak.
What are some ways to Reset my Maytag washing machine?
- Turn off your Maytag Centennial washing machine.
- Disconnect it from electricity socket. Keep it in this condition for 11 to 17 minutes.
- Plug your washer cable back to wall outlet.
How do you open a Maytag washer to repair it?
How to Take the Top Off a Maytag Washer
- Safety First. Remember that these appliances conduct electrical currents. ...
- Lower-Front Screws. As you go through this process, you will see that it is largely about removing screws. ...
- Front Panel. ...
- Lifting the Front Edge. ...
- Machine Bolts. ...
- Returning Everything. ...
See more
See more
How do you troubleshoot a Maytag washer?
4:2912:53How to Find & Fix Maytag Centennial Washer Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll lights will then flash on and off this selection is to wipe all the codes away from the machineMoreAll lights will then flash on and off this selection is to wipe all the codes away from the machine which is helpful to do if you have fixed the problem or you think you have fixed it.
Is it worth fixing a Maytag washer?
Repair: If the repair would cost less than 50% of the price of a new appliance and your machine still has several expected years of life left, a quick fix could be a cost-effective solution over replacing the entire washer. An active warranty can also make any repair worthwhile.
Why is my Maytag washer not spinning and draining?
Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.
How do you fix a Maytag washer that won't start?
This is how to properly reset a Maytag washer:Step 1: Unplug the machine.Step 2: Press and hold the POWER/START button for 5 seconds.Step 3: Hold down the PLAY/PAUSE button for 5 seconds.Step 4: Plug the machine back in and press POWER to restart.
What is the life expectancy of a Maytag washing machine?
A new washing machine has an average life expectancy of 11 years. Consumer Reports does not recommend replacing any appliance that is more than eight years old if it is a high-end model.
Is it cheaper to fix a washing machine or buy a new one?
Repair Costs Are Significant As a general rule, if an appliance repair will cost more than 50 percent of the price of a replacement, it might be prudent to buy a newer model if your budget allows for it.
What causes a washing machine not to drain and spin?
If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
What is the problem if the washing machine wont spin?
Normally, your washing machine won't go into a spin cycle until it's been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.
How do you fix a washer that won't spin?
How To Fix A Washer That Won't SpinLighten the load inside the washer. ... Rebalance the load in the washing machine. ... Check or repair the washing machine drain hose. ... Check for blown fuses. ... Check the washing machine lid safety switch. ... Replace the drive belt in your washing machine. ... Replace the motor in your washing machine.
Is there a reset button on a Maytag washing machine?
Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.
Where is the reset button on a Maytag washer?
Resetting a Maytag coin-operated washer Hold down the Delicates and Knits button for five seconds. The washer's LED display should now flash and start to blink, which means the error codes have been resolved and the washer has reset.
Where is the fuse located on a Maytag washer?
Maytag washers have a fuse in the lid-switch assembly. Maytag top-loading washers have a fuse in the lid-switch assembly. When you close the lid after adding the laundry and soap, the lid's plastic switch contacts with the assembly underneath.
THE WASHING MACHINE WON’T DRAIN
If your washing machine won’t drain or your loads are coming out too wet, you may have a kink or clog in the drain hose, a drain pipe that’s too lo...
MY WASHING MACHINE WON’T SPIN
A washer needs to spin correctly in order to fully rinse clothes and drain water from the tub. Before scheduling a service call, check if the power...
WASHING MACHINE IS LEAKING
Water is meant to stay in the washer. But if you’re noticing some water appearing on the floor, it may be a simple fix. Try cleaning the door seal,...
MY WASHER IS NOISIER THAN EXPECTED
If you’ve just brought home a new washer, it’s possible that it makes some noises you aren’t familiar with. Many of these are normal and shouldn’t...
MY WASHER HAS ODORS
Washer odors are easily fixable and usually the result of a missed cleaning, a load left too long or too much detergent and fabric softener use. Tr...
Most Common Problems
The Maytag washing machine troubleshooting process begins with Repair Clinic's list of symptoms. Once you match your problem to one of the common technical causes we've included in our troubleshooting guide, you'll be on your way to a quality repair.
The Right Parts for the Job
We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.
What is a Maytag washer?
Maytag is the creator of some of the most popular washing machines on the market . They are known for their high-quality products that last a long time and for how well their machines hold up to their task; however, sometimes Maytag washers malfunction. If your Maytag washer won’t work, we’ll show you how to fix it – no plumber needed.
Why won't my Maytag washer spin?
Sometimes when you’ve gotten everything loaded into your washer, drizzled in your favorite detergent, the water’s filled, and the machines ready to go, your Maytag washer won’t spin. This is such a frustrating issue because you don’t know that it’s a problem until it’s too late – you already have your laundry soaking wet and soapy.
Why is my Maytag washing machine not draining?
The first reason that your washer may not be draining properly is because of an issue with the drain hose that’s attached to your machine.
Why is my Maytag washer light blinking?
The first suggestion that Maytag makes to fix a blinking lock light is to check the lock striker. The lock striker is the piece on the main washing drum that fits into a slot on the washing machine lid.
Why is my washer draining water at one minute?
It can be assumed that a blocked drain pump is your issue because the one minute mark on the cycle is approximately when the washer drains the water from your load of laundry. At the one minute mark, sensors are used to make sure that the drainage pipe is in working order, and if it isn’t, then nothing will drain.
Why does my washer light blink?
If your washing machine “locked” light is blinking, it means that there is some sort of obstruction in the locking mechanism.
What to do if your washer isn't plugged in?
Check first to see if it’s plugged in. If your washer isn’t plugged in, it’s likely that you’ll need to reset the outlet. That is likely the issue because washers use a decent amount of power. If that still doesn’t resolve the problem, then reset the outlet at the breaker.
Troubleshoot
We’ll help you quickly diagnose and resolve select issues with links to video content, error codes, appliance maintenance and product info.
Connected Appliances
Click below for information regarding connected appliance troubleshooting.
