You have to heat up the plastic part of the switch with a hairdryer, so you can fold up the thick foil witch the blade of a carpet knife. If you loosen the foil you can see the upper Part of the switch, it's only fixed with a small duct tape. Remove the upper part and clean the oxidized parts of the switch, with fiberglass pen and contact cleaner.
Full Answer
When to replace the power supply on a Maytronics pool pump?
Replace Power Supply: If your power supply unit’s “POWER/ON” button does NOT light up at all, you may need a replacement power supply. Take it to us at E-Z Test Pool Supplies, we are an authorized Maytronics dealer that also repairs Dolphin products.
Can I get spare parts for my Maytronics robot?
Unless you have a spare robot for parts, internal maytronics parts are impossible to get. Your dealer will send your robot out for repair. Prevention is the best remedy. Avoid operating your Maytronics cleaner under any conditions that will clog the bag and prevent water circulation around the motor housing.
How do I contact Maytronics customer support?
If you have any questions about warranty coverage, issues with the diagnostic or RMA procedure or are unsure of which part your require, please contact Maytronics Customer Support at (888) DOLPHIN. Please provide us with as much detail regarding your issue as possible.
Who is the dealer for Maytronics dolphin repair service?
Aquaquality Pools and Spas Inc,is now a dealer and provider Of Maytronics Dolphin repair service for both Dolphin Pool Cleaners and Tiger Shark Pool Cleaners. 1-866-876-8643 Ask An Authorized Maytronics Service Center a Question (new window)
How do I reset my Maytronics power supply?
Restart the cleaner; press and hold the reset button until the light goes off (approximately 5 – 20 seconds). If light still does not go off, take your Dolphin to your local dealer or call Maytronics Customer Service.
How do you test a dolphin power supply?
0:100:42A_LINE_02_Power_Supply - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst test the power supply. Begin by unplugging the floating cable from the power supply andMoreFirst test the power supply. Begin by unplugging the floating cable from the power supply and inserting the round end of the dolphin tester into the Amphenol plug socket.
Can Maytronics Dolphin power supply get wet?
Can you leave the Dolphin in the water? It is safe to leave your Dolphin cleaner in the water when not in use. However, (when adding chemicals to the pool) please remove the Dolphin until the proper chlorine and PH balance are obtained.
How do you troubleshoot a Maytronics dolphin?
TroubleshootingCheck that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.Turn the power supply off. ... Unplug the power supply.
How do you test a Maytronics power supply?
Testing the power supplyConnect the tester to the power supply.Switch the power supply on.If the tester light is on, proceed to test the cable.If the tester light is off, check the power socket and AC cable. If they are working, then replace the power supply and proceed to test the cable.
How do I test my pool cleaner power supply?
1:367:51SUPREME_M_Full - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is accomplished by turning a robot upside down on the workbench plugging. The power supply intoMoreThis is accomplished by turning a robot upside down on the workbench plugging. The power supply into the wall. Plugging the floating cable into the power supply.
How do I fix my Dolphin power supply?
There may be a problem with the blue cable or the Dolphin cleaner itself....How To Fix My Dolphin Power SupplyUnplug the cleaner. ... Turn the cleaner over and rotate the brushes by hand. ... Using a water-jet sprayer setting, hose the tracks thoroughly from front to back to loosen any clogged debris or lodged objects.
How long do Dolphin robotic pool cleaners last?
Generally, you can expect at least 5 years' service from your quality robotic pool cleaner. The more expensive units are generally better quality – you do get what you pay for. If you keep your robotic pool cleaner in good condition, there is no reason it shouldn't last much longer.
Can you get electrocuted by a pool robot?
Two 10-year-old girls died while swimming in a private pool on Wednesday in Savyon after a malfunctioning pool-cleaning robot apparently electrocuted them. An autopsy is to be conducted to determine the exact cause of death before the girls are buried.
How do you use a Maytronics power supply?
Basic Operation: Plug the Power supply into an electrical outlet. The LEDs will turn on and the robot will start to operate. If no program is selected, the robot will perform a single cleaning cycle. You can program the power supply at any time.
Why is my pool robot not working?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
How long is the Maytronics Dolphin warranty?
for 3 yearsThe Best Warranty in the Industry Maytronics warrants that your Premier Dolphin pool cleaner will be free from defects in material and workmanship for 3 years. To prove how serious we are about delivering the best-in-class high performance robot, the Dolphin Premier is backed by the very best warranty in the industry.
How do you use a Maytronics power supply?
Basic Operation: Plug the Power supply into an electrical outlet. The LEDs will turn on and the robot will start to operate. If no program is selected, the robot will perform a single cleaning cycle. You can program the power supply at any time.
Why is my robotic pool cleaner not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
Why is my pool cleaner not working?
Most likely, the key reason is a congested pool filter or skimmer basket, or a clog at the mouth of your pool cleaner. If you own a particularly powerful pool pump or your water-flow is really strong, your cleaner will probably move faster than normal.
Why is my dolphin pool cleaner doing wheelies?
What causes automatic pool cleaners to flip or do wheelies? The water level in a pool is one of the most common causes for this problem. When the water level is too high, the water line is very close to the coping. So when the cleaner starts to climb the wall, it hits the coping and flips on to its back.
Can you put a robot back together?
No instructions are included to put it back together because parts are unavailable. The motor assembly inside the robot body is held in place by screws accessible once the sideplates are removed. Inside the box is the pump, drive motor, circuit board and a counterweight to offset the buoyancy of the air filled box.
Can you get Maytronics parts?
Unless you have a spare robot for parts, internal maytronics parts are impossible to get. Your dealer will send your robot out for repair. Prevention is the best remedy. Avoid operating your Maytronics cleaner under any conditions that will clog the bag and prevent water circulation around the motor housing.
martrader17
Hi all. My name is Mario and this is the first time. I am not a technician but I am persistent and willing to learn. I have a pool robot that three days ago a lightning strike occurred and the power supply stopped working. It only turns on the lights of the power button but it does not work.
dave9
Can you determine how it powers on, perhaps it grounds the CTRL pin on the header pictured?
martrader17
Thanks for your reply. Check that the power cord is okay. This right. Check if 29V came out and it does not have it, it is 0 I don't think it's the ignition because when I turn it on the dash lights up and the other side is 120 V.
Why is my 9995670 not working?
if you own a 9995670 Power Supply and it is not working any more , in many cases the reason is the power switch. It will be oxidized by moisture . So you have to open it. It is not necessary to open the whole case, only the power switch.
How to get epoxy off plastic?
Use paint thinner. Soak a paper towel with paint thinner and moisten the epoxy. Wait about 10 mins or so and take a wedge or screw driver and with a soft blow hammer pop the epoxy loose from the plastic. Soon enough will be lose where you can peel out the epoxy and expose the screwws.
