How to Fix a Shower Diverter Gate
- Plug the drain hole. For the first step, you will need to make sure that everything is in its place. ...
- Turn off the water supply. Next thing to do before you start the repairing process is to turn off the water supply for your bathroom.
- Remove the shower diverter’s knob. ...
- Detach the shower diverter from the water supply line. ...
- Remove the rubber washer. ...
How to fix or repair a broken shower Moen?
Equipment / Tools
- Rag
- Allen wrench
- Phillips screwdriver
- Moen cartridge puller (optional)
- Needle-nose pliers
- Flashlight
How to repair a Moen kitchen faucet cartridge?
- Under a cap on top of the handle
- Behind a plug button on the side of the handle
- No screw: Base of handle unthreads
How to repair a Moen Mixing valve for a shower?
Using the pliers, grab on to the mixing valve. Move it gently from side to side to loosen it. You can then pull the valve cartridge out. Check the valve for any visible signs of wear or cracks. Use a brush to remove dirt and get a better look at the valve.
How to remove a Moen 1222 shower cartridge?
- Clean the inside of the shower valve before installing the new cartridge.
- Apply plumber’s grease on the cartridge and push it inside the valve. ...
- Push the cartridge retaining clip back in being careful not to drop it inside the wall.
- Install the escutcheon.
- Slide in the stop tube, temperature limit stop and handle adapter.
How do I fix my Moen diverter?
0:016:39Moen Diverter Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you need to do is use a two millimeter allen key which i've got here plug it in the littleMoreSo what you need to do is use a two millimeter allen key which i've got here plug it in the little hole on the top like a catch and then just turn it anti-clockwise.
Can a shower diverter be repaired?
Once you've determined that your shower diverter is broken, don't delay in repairing it. Though it might be an easy task to put off, a broken shower diverter wastes water and creates a poor shower experience. Repairing a shower diverter is a home improvement project that you can complete in just one day.
How do you fix a shower diverter pull up?
0:196:11Tub faucet spout diverter pull lever broke off - DIY fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround the actual medium point of your spout. And the shower wall just carefully grab a utilityMoreAround the actual medium point of your spout. And the shower wall just carefully grab a utility knife and remove. It. And again in our case we just got this rubber seal you can purchase.
How do you replace a Moen push button shower diverter?
Clean the inside of the diverter valve (#2) with a toothbrush and a 50/50 solution of white vinegar and water. Place a 7/8" deep well socket or pliers on the hex portion of the push button diverter (#1) and thread it into the diverter valve (#2) clockwise to install.
How do I know if my shower diverter valve is bad?
First, if the valve is engaged but water continues to come out of the tub spout only, the gate is severely damaged or has fallen out completely. Second, if the valve is engaged but the showerhead experiences low water pressure and water continues to drip from the spout, the gasket has failed or is starting to fail.
How do you install a Moen tub spout diverter repair kit?
1:403:10How to Install a Front End Diverter Spout Repair Kit 300242 - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're gonna slide it in there. And you see kind of the tip on there right there the metal tip andMoreYou're gonna slide it in there. And you see kind of the tip on there right there the metal tip and where you have the hole there you put those two together nicely.
Why does my shower diverter not work?
The most common issue with a shower diverter is when water comes out of both the tub faucet and the showerhead. Check to be sure there is no residue clogging the shower diverter lever from fully lifting or lowering. If everything looks clear, the problem could be worn-out parts in the shower diverter valve.
How do you replace a diverter spout?
0:153:36how to replace tub spout, change tub diverter. Easy! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt. So first we're going to just try to spin this guy off. And it's spinning pretty easy we've got aMoreIt. So first we're going to just try to spin this guy off. And it's spinning pretty easy we've got a set screw under here. But it looks like this will probably just spin.
How do you fix a push button diverter?
0:444:17How To Replace Install Diverter Push Button Shower Tub Easy SimpleYouTubeStart of suggested clipEnd of suggested clipNow that the screw is out we can go ahead and just pull the knob out our next move we're going toMoreNow that the screw is out we can go ahead and just pull the knob out our next move we're going to remove the cover. And we do that by removing the screws on each side of the knob.
How do you remove a diverter valve from a Moen faucet?
Unscrew and remove the handle, then pull out the stem extension with pliers and remove the escutcheon and the wall tube to expose the diverter bonnet. Unscrew this with a socket wrench, then pull out the diverter using needle-nose pliers.
How does a push button shower diverter work?
In short, it diverts water up into the showerhead instead of coming out of the tub spout. The user typically adjusts the faucet to the preferred water temperature before activating the diverter and sending water to the showerhead.
What causes shower diverter not to work?
The most common issue with a shower diverter is when water comes out of both the tub faucet and the showerhead. Check to be sure there is no residue clogging the shower diverter lever from fully lifting or lowering. If everything looks clear, the problem could be worn-out parts in the shower diverter valve.
How much does it cost to replace shower diverter?
Replacing a shower diverter valve costs $225 to $575, including materials and labor. A shower diverter valve switches the flow of water between the bathtub spout or shower head and is typically controlled by a small handle located on the center trim plate or near the tub spout.
How do you fix a bathtub diverter?
0:143:21Repair Leaking Tub Spout Diverter Pull in Shower Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pulling up on the diverter. Knob once that comes off all of the parts will come loose. So we'llMoreAnd pulling up on the diverter. Knob once that comes off all of the parts will come loose. So we'll take a look inside the tub spout in a little bit but first let's check out the washer.
How do you replace a diverter valve?
Diverter Valve on a SpigotUnscrew the set screw. See how the spigot is attached to the wall. ... Unscrew spigot from the wall. Be careful! ... Wash Supply Pipe. Make sure that you clean off any bits of gunk from the supply pipe. ... Replace new spout on the copper pipe. ... Test it and make sure it works!
What is a Moen shower valve?
Moen pressure-balance shower valves are designed so they sense hot and cold water pressure and keep them in balance, preventing the shower from sudden surges of hot or cold water. When the shower valve begins leaking or fails to correctly balance the hot and cold water, fixing the problem is usually a simple matter of replacing the insert cartridge.
How to remove a Moen faucet?
Unscrew the black plastic handle adapter with a Phillips screwdriver and pull it straight out. Pull the two white plastic pieces (the temperature-limit stop kit; not all Moen faucets have these) straight out, keeping the two pieces together so you don't loose the temperature setting. Grip the chrome sleeve and pull it straight out. This will expose the retaining clip that holds the cartridge in place.
How to use a Moen cartridge puller?
To use the tool, fit it onto the end of the cartridge and thread the puller screw into the end of the valve stem (the same part that accepts the valve handle). Make sure that it goes in straight and is not cross-threaded.
How to remove cartridge retaining clip?
Note the location of the cartridge retaining clip; you much reinstall it the same way after the new cartridge is in place. Use needle-nose pliers to grip the top of the clip and pull it straight up to remove it. Set the retaining clip aside; you will use it with the new cartridge.
How to turn down the temperature of a scald guard?
To turn the water temperature down, move the outer white piece to the right to limit the hot water. The number of splines you move will depend on how much restriction you want.
How to drain water from a house with no water shut off valve?
Drain any water remaining in the pipes by turning on the faucet. If you had to turn off the water at the main house shutoff, then open the lowest faucet in the home to drain the pipes.
How to put a H C cartridge in a valve?
Insert the cartridge into the valve body so that the "H C" marking on the face of the cartridge is on top (hot is on the left and cold is on the right). Push in the cartridge as far as it will go. Use the plastic adapter that comes with the new cartridge to help position the cartridge and push it into the valve body.
How to make sure water is coming out of shower head?
1. Start this process by ensuring that the water is coming out of the tub faucet and not the shower head. Although it is not necessary to turn off your water supply, you want to make sure that if water does start coming, you don’t get soaked in the process! 2.
What tool to remove a screw from a faucet?
2. Note that the tool to remove the screw could be an Allen Wrench, Flat Head Screwdriver, or a Phillips Head Screwdriver. 3.
How to remove a knob from a sandbox?
Start by removing the knob. Find the screw, if not visible it is located under the plastic button which will need to be popped off using a small flathead screwdriver. 1. Once the knob has been removed, use your hand or a handle remover to remove the base.
Is it bad to have a shower faucet leaking?
It is never a good thing when your shower tub faucet starts leaking, but it is a good thing when you know what to do to fix it! As long as you have the time, tools, and parts for the job you can definitely learn how to fix shower diverter all on your own!
How to tell if a shower diverter is a two valve or three valve?
When you remove a tee-valve from the wall, you find a single copper pipe. With two-valves and three-valves, you’ll find the corresponding number of copper pipes . If your shower diverter is a two-valve, focus on the temperature dial. This is because it often doubles as a shower diverter gate.
What to do if your diverter gate is stubborn?
If your diverter gate stays stubborn after your vinegar soak, try using a lubricant to make it work better. Any cooking spray will do, and you probably have some in the kitchen.
How to stop a handheld shower from leaking?
When you want to stop your handheld showerhead from leaking, you need to clean the inner parts of your diverter gate. Step 1: Turn off your water supply from the main spigot. This prevents flooding.
What does a shower valve do when it is not working?
If your bathtub has a showerhead, your shower valve redirects water from the showerhead to the tub faucet. When it’s not working, water simultane ously pours from both outlets. It’s easy to fix, so let’s learn how. Shower valves have two parts:
Why does my diverter gate keep squeaking?
Option 1 – Clean your spout. Sometimes, the diverter gate gets stuck. When you try to turn it or pull it up, it refuses to budge or makes squeaky, grating noises. If you do manage to pull it up, it may stick at the top and refuse to push back down. This is probably due to accumulated dirt, grease, and limescale.
How to clean a spout with vinegar?
If you like, you can mix the vinegar with water. Step 3: Wrap the plastic bag around your spout, submerging the spout. Step 4: Hold the bag in place using a rubber band, string, or shoe-lace. Step 5: Leave the faucet submerged for three or four days, checking it once a day.
