- Turn off the Water. You cannot repair a shower faucet when there is full water pressure in the pipes. ...
- Remove the Faucet Handle. The faucet handle is attached to the cartridge using a screw on its underside. ...
- Remove the Old Faucet Cartridge. Once the faucet handle is out, you will see a plastic holder (usually black) connected to the cartridge using a Philips screw.
- Install the New Cartridge. Prior to installing the new cartridge, it is a good practice to first clean the valve. ...
- Test the New Moen Shower Cartridge. Turn on the water supply to the shower and check for leaks when the faucet is turned off. ...
Full Answer
How to fix Moen bathroom faucet?
Centerset Faucets
- Clear Out The Cabinet. To start things off, clear out the cabinet beneath the sink (if applicable). ...
- Shut Off The Water Supply. Then, shut off the water supply to the faucet you’re working on. ...
- Remove The Water Lines. Locate the base of the faucet beneath the sink. ...
- Tighten The Nuts. ...
- Check Your Work. ...
How to fix a dripping Moen faucet for free?
Start with the retaining nut, then look for other problems
- Tighten retaining nut. If you're lucky, you can fix your leaking faucet by simply tightening the nut under the handle. ...
- Remove the stem. Next, remove the faucet stem. ...
- Replace washer assembly. Keep track of the parts as you disassemble the faucet so you can install the new ones in the same order.
- Remove the vacuum breaker cap. ...
- Vacuum breaker parts. ...
How to remove and replace a Moen shower cartridge?
- Take off the faucet handle cover using a flat-bladed screwdriver.
- Remove the faucet handle screw.
- Next, take off the faucet handle itself. ...
- Remove and ‘SAVE’ the retaining clip.
- Pull out the old valve cartridge using a Moen extractor tool (these are not cheap – they cost around $30).
How to fix a Moen single handle kitchen faucet?
Tightening Moen Kitchen Faucet Handle
- Turn off the water and cover the drain. Working on the faucet handle requires the same prep work as working on its base. ...
- Locate the set screw. All Moen faucet handles are held in place by a set screw located under a decorative plate. ...
- Tighten the screw. ...
- Replace the decorative cap. ...
- Turn on the water and check for leaks. ...
How to remove a Moen faucet?
What is a Moen shower valve?
How to use a Moen cartridge puller?
How to remove cartridge retaining clip?
How to drain water from a house with no water shut off valve?
How to put a H C cartridge in a valve?
See more
How do you fix a leaking Moen shower faucet?
0:2810:07How to fix a leaking Moen Shower - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep is you're going to verify that the water is in fact off by turning the handle. And this alsoMoreStep is you're going to verify that the water is in fact off by turning the handle. And this also will drain out any excess water that's inside the valve.
How do you fix a Moen single handle shower faucet?
0:269:09How to Repair a Moen Shower Faucet Step-by-Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm going to show you how easy it is to install it these are for single handle faucets. And youMoreAnd I'm going to show you how easy it is to install it these are for single handle faucets. And you can pick these up at a home depot or any other hardware store like that.
How do I stop my Moen bathroom faucet from dripping?
0:021:36How To Fix a Dripping Moen Faucet (HowToLou.com) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you look at your new one there's a little tab right there that goes to that slot right there soMoreIf you look at your new one there's a little tab right there that goes to that slot right there so just line those two up and push it in put your brass ring back on tighten. It with pliers.
Why is my new Moen shower faucet leaking?
Your faucet may contain a ceramic, brass, or rubber seat that is meant to form a seal at the bottom of the cartridge opening. The seat can become damaged with use so that it no longer fits correctly into the hole in the cartridge, which allows water to leak. The O-ring may also become cracked and cause a leak.
How do you fix a leaky single handle shower faucet?
0:172:38Repairing a Leaky Single Handle Tub/Shower Ball-Type FaucetYouTubeStart of suggested clipEnd of suggested clipTurn off the main water supply to your home. For an obstacle remove the index button by prying offMoreTurn off the main water supply to your home. For an obstacle remove the index button by prying off with the screwdriver. Then unscrew the handle screw. And remove the handle.
How do I know which Moen shower valve I have?
Look closely at the handle buttons that were attached to the shower valve. Typically, "Moen" will be written in the middle of the "Hot" and "Cold" buttons. If you do not see this, the handle buttons have been replaced, or the "Hot/Cold" button is a lever (wall escutcheon).
What causes a Moen faucet to drip?
Recommended Solution-Moen faucets are designed with an interior component called a cartridge. This part is responsible for controlling the water flow. If a faucet is leaking water from the spout, the reason is usually the cartridge.
How do you take apart a Moen faucet?
Some Moen faucets have handles that remove by loosening the screw in the back of the handle. To loosen this screw use a 3/32" hex wrench. After the handle has been removed unscrew the spout collar nut by turning counterclockwise then lift and rotate the spout.
How do I change a Moen shower cartridge?
1:043:14How to Remove & Install the 1222 Cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipLoosen the handle adapter screw and remove the adapter. Pull off the key stop and adjustableMoreLoosen the handle adapter screw and remove the adapter. Pull off the key stop and adjustable temperature limit stop then the stop tube. Pull out the cartridge retaining clip with needle nose pliers.
How do you know which Moen cartridge you need?
0:063:58Old plumber shows tips and tricks on moen faucets. Choosing the right ...YouTubeStart of suggested clipEnd of suggested clipSimply by going to your faucet years ago go into your faucet. And pull them pulling. On yourMoreSimply by going to your faucet years ago go into your faucet. And pull them pulling. On your cartridge if the handle pulls out it's a 12 25 cartridge.
How long should a Moen cartridge last?
20 to 30 yearsThe system has expensive cartridges, they cost about $30 (2014) to replace, but they last a long time -- 20 to 30 years. It's not a bad deal, and unlike modern ceramic faucets, Moen still makes the same part to put into valve bodies made 40 years ago!
How do I know if my Moen cartridge is bad?
Symptoms of a bad Moen 1225 and 1222B Cartridge:Leaking from the handle, tub spout or shower head when off.Difficult to open or close shower valve.Difficult to turn shower handle.Inability to get very hot or very cold water.
How do you fix a shower diverter pull up?
0:196:11Tub faucet spout diverter pull lever broke off - DIY fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipAround the actual medium point of your spout. And the shower wall just carefully grab a utilityMoreAround the actual medium point of your spout. And the shower wall just carefully grab a utility knife and remove. It. And again in our case we just got this rubber seal you can purchase.
How do you take apart a single handle faucet?
0:182:44Repairing a Leaky Single Handle Ball-Type Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis may require using an Allen wrench to loosen the handle. There may be a button that covers theMoreThis may require using an Allen wrench to loosen the handle. There may be a button that covers the screw that needs to be removed first and then you can loosen the screw and remove the lever handle.
How do you disassemble a Moen adjustable shower head?
1:056:21How to Disassemble and Clean a Moen Shower Head - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimple this piece comes out through the back you got to pop that off it's fairly simple i just pushMoreSimple this piece comes out through the back you got to pop that off it's fairly simple i just push it flat against the counter.
How do I fix my shower pull up?
0:143:21Repair Leaking Tub Spout Diverter Pull in Shower Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pulling up on the diverter. Knob once that comes off all of the parts will come loose. So we'llMoreAnd pulling up on the diverter. Knob once that comes off all of the parts will come loose. So we'll take a look inside the tub spout in a little bit but first let's check out the washer.
1. Turn off the Water
You cannot repair a shower faucet when there is full water pressure in the pipes. The first to do therefore is to turn off water supply to the shower (and possibly the entire house) and drain that which is already in the pipes.
2. Remove the Faucet Handle
The faucet handle is attached to the cartridge using a screw on its underside. To access the cartridge you will first need to remove the handle. While most Moen handles will look this way, there also other variations. One way or the other the handle will have a screw somewhere.
3. Remove the Old Faucet Cartridge
Once the faucet handle is out, you will see a plastic holder (usually black) connected to the cartridge using a Philips screw. Remove the handle holder using the Philips screwdriver.
4. Install the New Cartridge
Prior to installing the new cartridge, it is a good practice to first clean the valve. Use an old toothbrush, to scrub off calcium and other mineral deposits. If there are lots of debris inside the valve, turn on the water slowly to flush out the debris. This will prevent leaking from the new cartridge.
5. Test the New Moen Shower Cartridge
Turn on the water supply to the shower and check for leaks when the faucet is turned off. Open the water and let it run and then turn it off. Check if the faucet is shutting off precisely.
How to remove a Moen faucet?
Unscrew the black plastic handle adapter with a Phillips screwdriver and pull it straight out. Pull the two white plastic pieces (the temperature-limit stop kit; not all Moen faucets have these) straight out, keeping the two pieces together so you don't loose the temperature setting. Grip the chrome sleeve and pull it straight out. This will expose the retaining clip that holds the cartridge in place.
What is a Moen shower valve?
Moen pressure-balance shower valves are designed so they sense hot and cold water pressure and keep them in balance, preventing the shower from sudden surges of hot or cold water. When the shower valve begins leaking or fails to correctly balance the hot and cold water, fixing the problem is usually a simple matter of replacing the insert cartridge.
How to use a Moen cartridge puller?
To use the tool, fit it onto the end of the cartridge and thread the puller screw into the end of the valve stem (the same part that accepts the valve handle). Make sure that it goes in straight and is not cross-threaded.
How to remove cartridge retaining clip?
Note the location of the cartridge retaining clip; you much reinstall it the same way after the new cartridge is in place. Use needle-nose pliers to grip the top of the clip and pull it straight up to remove it. Set the retaining clip aside; you will use it with the new cartridge.
How to drain water from a house with no water shut off valve?
Drain any water remaining in the pipes by turning on the faucet. If you had to turn off the water at the main house shutoff, then open the lowest faucet in the home to drain the pipes.
How to put a H C cartridge in a valve?
Insert the cartridge into the valve body so that the "H C" marking on the face of the cartridge is on top (hot is on the left and cold is on the right). Push in the cartridge as far as it will go. Use the plastic adapter that comes with the new cartridge to help position the cartridge and push it into the valve body.
How to remove a Moen faucet?
Unscrew the black plastic handle adapter with a Phillips screwdriver and pull it straight out. Pull the two white plastic pieces (the temperature-limit stop kit; not all Moen faucets have these) straight out, keeping the two pieces together so you don't loose the temperature setting. Grip the chrome sleeve and pull it straight out. This will expose the retaining clip that holds the cartridge in place.
What is a Moen shower valve?
Moen pressure-balance shower valves are designed so they sense hot and cold water pressure and keep them in balance, preventing the shower from sudden surges of hot or cold water. When the shower valve begins leaking or fails to correctly balance the hot and cold water, fixing the problem is usually a simple matter of replacing the insert cartridge.
How to use a Moen cartridge puller?
To use the tool, fit it onto the end of the cartridge and thread the puller screw into the end of the valve stem (the same part that accepts the valve handle). Make sure that it goes in straight and is not cross-threaded.
How to remove cartridge retaining clip?
Note the location of the cartridge retaining clip; you much reinstall it the same way after the new cartridge is in place. Use needle-nose pliers to grip the top of the clip and pull it straight up to remove it. Set the retaining clip aside; you will use it with the new cartridge.
How to drain water from a house with no water shut off valve?
Drain any water remaining in the pipes by turning on the faucet. If you had to turn off the water at the main house shutoff, then open the lowest faucet in the home to drain the pipes.
How to put a H C cartridge in a valve?
Insert the cartridge into the valve body so that the "H C" marking on the face of the cartridge is on top (hot is on the left and cold is on the right). Push in the cartridge as far as it will go. Use the plastic adapter that comes with the new cartridge to help position the cartridge and push it into the valve body.
