- Unroll a sheet of MonoKote on a clean work surface, and lay the model part on top of it. ...
- Remove the clear backing from the MonoKote by attaching a small piece of cellophane tape on each side of the sheet and pulling gently.
- Place the MonoKote, adhesive side down, over the part. Allow a minimum overlap of 1 inch (25 mm) all around except the wing tip which needs a minimum of ...
- Set the heat sealing tool to 275 F (135 C) and allow it to come to temperature before proceeding.
- Pull the MonoKote to the edge of the piece to be covered, and run the heat sealing iron along the edge to activate the adhesive and seal MonoKote to ...
- Unroll a second sheet of MonoKote, and repeat the process on the other side of the aircraft part.
- Trim the edges carefully with the utility knife, leaving a 1/8 inch to 1/4 inch (3 to 6 mm) overlap.
- Finish the edge by carefully folding the top edge under to the bottom side and using the heating iron to seal it in place.
How do you use Monokote?
Continue working around the edges, left to right, top to bottom, right to left and bottom to top. While sealing the edges, keep the MonoKote pulled taut so that when you finish tacking down the edges, the covering is smooth and wrinkle free.
How do you mix Monokote patching compound?
When mixing full pails of MONOKOTE® Patching Compound, add 1½ gallons of potable water to the pail of MONOKOTE® Patching Compound Mixture. When mixing less than full pails of material, add 1 quart cup of water to 4 quart cups of MONOKOTE® Patching Compound.
How to iron on Monokote covers?
Try for a good wrinkle-free covering, although MonoKote does have excellent shrinking qualities. Set your iron temperature at 225°. Center the piece on the part and tack the covering at one end. Now go to the other end, pull gently, and tack it. Go to the middle and tack both sides, gently pulling the covering.
How has Monokote changed the way we cover our models?
MonoKote and other films have changed the way we cover our models throughout the years. It was not initially accepted by those who used silk and dope and painted their models. To them, it cheapened the model and they looked down on it, but Sid kept selling it, and in time it became a desirable covering medium.
How do you repair a monocoat?
Spot RepairsSand the repair area as needed to remove damage and expose raw wood.Dampen the area with water. Allow to completely dry.Apply with a cotton cloth, the same color oil that was used originally to coat the floor.Let it react for 10 minutes. Wipe the excess oil off with a cloth, dampened with Monocoat Oil.
How do you apply monokote to Wings?
3:355:42Monokote 101 Part I.mov - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to Center it up so that the overhang is equal on the leading edge and the trailing edge.MoreYou want to Center it up so that the overhang is equal on the leading edge and the trailing edge. And you can make a little minor adjustments before starting to tack it.
How do you cover monokote?
Covering StepsSand the airframe to perfection.Clean the workbench and airplane parts with a vacuum.Seal the covering all the way around after trimming with the iron set at 225°.Use a heat gun to shrink the covering.Iron the covering to the wood with the iron set at 350° using an iron sock.Apply any graphics.
How do you fix an airplane wing?
1:462:49Wing repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipBecause to pull the wing off you have to pull all the control cables out and pull the landing gearMoreBecause to pull the wing off you have to pull all the control cables out and pull the landing gear out and have to make cradles to hold the fuselage in the wing.
Will monokote stick to paint?
Yes, but if you're not covering the entire surface (Like adding a stripe or shape) you'll have to be very careful about melting the paint at the edges. You'll also be better off with Ultracote as it doesn't need as much heat. RE: Can I apply Monokote or Ultracote to plastic ? Thanks, I'll give it a shot.
How do you clean monokote?
For best results, clean MonoKote-covered models with a covering cleaner/polish, or Detergent (dishwashing liquid, glass cleaner, etc.) can also be used. 3. Dents in MonoKote, as a result of any accident, can be removed simply by applying heat over the affected area.
What is monokote made of?
Mylar-MonoKote is a Mylar-based material, glossy in finish, and it shrinks during heating. UltraCote, a polyester-based material, is less glossy and better resembles a painted finish.
Is monokote still available?
So apparently, Monokote has been discontinued after 52 years in production.
How do you remove monokote from balsa?
start with a tip or a root and apply slight heat with a heat gun and peel back a small area to get a finger grip on it. apply even heat accross the wing / surface ahead of the area you are pulling to loosen the adhesive and allow it to pull free.
How do you fix broken Styrofoam on a plane?
1:296:56Top Secret Foam Repair, a new trick to fixing your foam airplane - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou don't want to leave old residue on there and I use flexible spackle sandable spackle veryMoreYou don't want to leave old residue on there and I use flexible spackle sandable spackle very lightweight and expensive pick it up at your low hardware store next to nothing.
How do you fix a broken foam plane?
4:2512:18How To Repair Broken Foam RC Plane Part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipI went ahead and I got some of this stuff it's called kicker or accelerator. It's just a littleMoreI went ahead and I got some of this stuff it's called kicker or accelerator. It's just a little spray you spray it on your glue joint. And it cures it within seconds.
What are the typical repairs for aircraft structures?
AIRCRAFT ENGINES.FUEL & FUEL METERING SYSTEMS.INDUCTION & EXHAUST SYSTEMS.IGNITION & ELECTRICAL SYSTEMS.STARTING SYSTEMS.LUBRICATION & COOLING SYSTEMS.PROPELLERS.ENGINE REMOVAL & REPLACEMENT.More items...
How do you use Top Flite monokote?
18:5259:55Covering with Top Flite Monokote - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you're going to the root to the tip. And then the trailing edge in the leading edge in the middleMoreSo you're going to the root to the tip. And then the trailing edge in the leading edge in the middle then pulling diagonally you'll tack the two corners. The other two corners.
How do you apply monokote trim?
4:018:23MonoKote Trim Sheets for Newbies! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo now we're going to apply two of these number sevens onto the sample sample board what will happenMoreSo now we're going to apply two of these number sevens onto the sample sample board what will happen is we it's very easy you simply peel off the backing. And onto the monocote you put the.
How do you put monokote over monokote?
It is best to apply monokote in a single layer with a 1/4 " overlap between colours and patterns and seal them with trim solvent to make them one piece and then shrink it as a whole piece.
What temperature is monokote?
The substrate temperature shall be a minimum of 40°F (4.5°C) for at least 1-hour prior to the application of the MONOKOTE®. Additionally, the air and substrate temperature during application and for a minimum or 72 hours after application shall be no less than 40°F (4.5°C).
How long does it take to mix monotote patch?
When mixing less than full pails of material, add 1 quart cup of water to 4 quart cups of MONOKOTE® Patching Compound. Mix for 1-3 minutes until the mix is a lump-free, cohesive uniform slurry. All material is to be thoroughly wet. When properly mixed, MONOKOTE® Patch Compound has a potlife between 2 to 4 hours.
How long should you keep a monotote patching compound?
An air and substrate temperature of 40 °F (4.5 °C) minimum should be maintained for 8 hours prior to application, during application and 24 hours after application of MONOKOTE® Patching Compound.
What is a monotote patch?
MONOKOTE® Patching Compound is a mill-mixed plaster, (cementitious) fireproofing material that can be hand mixed and trowel applied as required for patching and repairs to surfaces . MONOKOTE® Patch Compound is hand-applied directly to the steel and/or well-bonded material using standard plastering tools and techniques. It has excellent bonding characteristics; it can be applied up to one inch per pass.
What is required to be removed prior to fireproofing?
Surfaces to which fireproofing is applied must be thoroughly cleaned of all foreign material which might impair adhesion. All loose material, including dirt, loose rust, mill scale and any other foreign material, that would impair adhesion of the patching material, must be removed prior to patching. Where damaged material extends to the steel or concrete substrate, removal should be to the steel or concrete substrate.#N#Where well-bonded material exists below the damaged material, removal of the damaged material should extend to the well bonded firm material. There is no requirement to remove well-bonded material that lies immediately beneath loosely bonded or poorly adhered material.#N#The patching material is keyed into the material surrounding the patch. It should be understood that the integrity of the surrounding material shall not have been impaired. If the surrounding material has been damaged it should be removed prior to patching.#N#When applying new material over in place material that has dried, it may be necessary to dampen or pre-wet the in place material sufficiently to prevent premature drying of the newly applied patching material.
What is the SDS number for Monokote?
gcpat.com | North America Customer Service: 1 877-4AD-MIX1 (1 877-423-6491) We hope the information here will be helpful.
Can you use monotote patching compound on frozen cake?
MONOKOTE® Patching Compound should not be used if it contains partially set, frozen or caked material. MONOKOTE® Patching Compound should not be retempered if the material has started to stiffen or set.
Do you have to remove well bonded material?
There is no requirement to remove well-bonded material that lies immediately beneath loosely bonded or poorly adhered material. The patching material is keyed into the material surrounding the patch. It should be understood that the integrity of the surrounding material shall not have been impaired.
What is a monokote?
This article has been viewed 32,372 times. Learn more... MonoKote is a lightweight plastic shrink wrap used to cover the surfaces ...
How to make a monokote model?
1. Unroll a sheet of MonoKote on a clean work surface, and lay the model part on top of it. Carefully outline the part with a fine tip marker, and cut out the section allowing an extra 2 inches (5 cm) in width and 4 inches (10 cm) in length.
How much overlap do you need for a monocote?
Place the MonoKote, adhesive side down, over the part. Allow a minimum overlap of 1 inch (25 mm) all around except the wing tip which needs a minimum of 3 inches (75 mm). ...
How many colors does Monokote come in?
MonoKote comes in approximately 50 colors as well as clear. It is available in opaque, flat, transparent, metallic, pearl and neon finishes. It is sold in a sheet form that the modeler cuts to size and applies to the aircraft surfaces, using a heating iron to activate the adhesive backing. They also offer trim sheets in 35 designs ...
How to make a Monokote roll?
Lay out the MonoKote roll with the back side up. Now lay your parts down and trace around them with a Magic Marker. Plan for the best usage as you go along. Trim around the outline leaving a 1-inch margin. When laying out two pieces that include the other side, flip the parts so that the glue side of the covering is against the wood. Don’t get caught with two pieces that look alike. You need opposites.
How to get windex out of iron?
Lay the stripe in place, pushing it around to make sure it is straight. Using a credit card as a squeegee, start from the center and move out, wiping away excess Windex with a paper to wel. Keep squeegeeing until all of the moisture is gone. Heat your iron to 200°.
Why does a blade last so long?
The blade lasts a long time because the slots in the trimmer are not evenly spaced. When the edge becomes dull, flip the blade end for end for a new set of cutting edges. There is a learning curve to using the tool, but it works well. 08. Lay the part on a flat surface and shrink the covering with a heat gun.
How to prevent warping of wood?
Lay the part on a flat surface. If it is a large part such as a wing, weigh it down before ironing the covering to prevent warping. On the sheeted surfaces, lay the iron down and move it in a circular motion, ironing the covering to the wood. Do this at every place the covering meets the wood.
How to control heat on a heat gun?
Let the hot air blow over the surface, not down on it. You can control the heat by holding the gun level with the surface then tipping it upward to get more heat. It is important to keep the heat gun moving. Spending too much time in one spot or letting it touch the covering can cause an unwanted hole to appear.
Does Monokote cover models?
MonoKote and other films have changed the way we cover our models throughout the years. It was not initially accepted by those who used silk and dope and painted their models. To them, it cheapened the model and they looked down on it, but Sid kept selling it, and in time it became a desirable covering medium. 02.
Monokote over Monokote
By logging into your account, you agree to our Terms of Use and Privacy Policy, and to the use of cookies as described therein.
Monokote over Monokote
Am wanting to put 3' bands at an angle, over my Phaeton 90 wings using Monokote. The wings are allready covered in Monokote. The wings are of rib construction.
