how to repair my samsung tv remote

See more

How do I reset my Samsung TV remote?

Remove the batteries, and then press the Power button for eight seconds to reset the remote. Then, reinsert the batteries and try to use the remote again.

How do I pair my Samsung remote to my TV?

On most Samsung TVs, the remote control sensor is located on the lower right hand side of the TV. If not, it is directly in the bottom center. Next, press and hold the Return and Play/Pause buttons simultaneously for at least 3 seconds. Your TV will begin syncing with the Smart Remote.

Why has my Samsung TV remote stopped working?

Batteries that are flat or incorrectly inserted are the most common reason for a remote to stop working or to work intermittently. Pairing is the term for connecting two Bluetooth enabled devices together. If your connection isn't working, re-pairing is a good way to try and fix the connection.

Why is my TV not responding to my remote?

A remote control that will not respond or control your TV usually means low batteries. Make sure you are pointing the remote at the TV. There also may be something interfering with the signal such as other electronics, certain types of lighting, or something blocking the TV remote sensor.

How do I reset my TV remote?

For Android TV models, refer to the How do I power reset my Android TV article....Reset the remote control.Open the battery compartment cover and remove the batteries.Press and hold the Power button for three seconds.Insert the batteries again and close the battery compartment cover.

How do I connect my remote to my TV?

0:252:09How to Program and Pair Your Remote - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply make sure the device you want to pair. Is on press and hold the setup button on your remote.MoreSimply make sure the device you want to pair. Is on press and hold the setup button on your remote. Control until the led light blinks twice.

Why is my remote not working even with new batteries?

If no light appears when you have tried ALL the buttons, and as you have replaced the batteries, make sure that the battery connection terminal in the remote are clean and bright and that the batteries are held "snugly" in position not loose. If all OK then the remote is faulty.

What do you do when your remote stops working?

1 Check the Batteries of the Supplied RemoteLift the back cover up and away from the remote.Remove and re-insert the 2 batteries.Replace the back cover on the remote, and slide down to click it into place.If the remote fails to respond properly after this, replace the existing set of batteries with new ones.

How do I sync my old Samsung remote?

Pairing for the first time1 Press any button on the remote except POWER.2 Watch lower left portion of TV screen for pairing information.3 Wait for Pairing attempt to finish. ... 1 Move to within 12 inches of the TV, and then aim the Smart Control at the TV's IR sensor.2 Press the RETURN and GUIDE buttons simultaneously.More items...

How do I pair my Samsung bn59 remote?

Push and hold the PROG button on your Adapter's remote until the LED on the remote illuminates, then press the INFO button. The remote's LED will slowly blink to indicate that it is currently in pairing mode. With the keys on your remote, enter the three-digit number that appears on your TV screen.

How do I reset my Samsung bn59 remote?

0:021:02How To Reset Samsung's TV LCD LED Remote Control - YouTubeYouTubeStart of suggested clipEnd of suggested clipButton three save four time then press up arrow right arrow and left arrows. Then press power buttonMoreButton three save four time then press up arrow right arrow and left arrows. Then press power button three to four. Time. Then press source button for few seconds.

Why is my Samsung remote not working?

The Samsung remote is not working. Troubleshooting your remote depends on the issue that you're having with it. If it seems like it's pressing buttons by itself, it may actually be that your remote's buttons are dirty. And if it won't work when you try to use it on your TV, there's a quick check you can perform to figure out if it's your remote ...

What to do if your remote won't work?

If it is the remote, it may need a pair of fresh batteries or a reset.

How to clean a remote control?

1 Remove the batteries from your remote control. To eliminate the possibility that the remote is sending commands to the TV, take the batteries out. 2 Unplug the TV. With the TV powered on, unplug the TV from the wall outlet. If the TV has a One Connect box, unplug it as well. 3 Clean the touch controls.

How to check if your camera is infrared?

Get either a digital camera or use the camera on your phone or tablet. Point the remote at the camera, and then press and hold the Power button on the remote. As you hold the button down, look at the camera's screen.

Why is my remote not working?

The most common are physical damage, battery issues, pairing issues, or issues with the infrared sensor on the remote or TV. And if it won't work when you try to use it on your TV, there's a quick check to perform to figure out if it's your remote or your TV at fault.

1. Reset your Samsung TV and remote

First, open up the back of your remote and remove the batteries. Then go ahead and unplug your TV from the wall and wait 60 seconds.

2. Replace weak or dead remote batteries

The life of batteries can depend on a wide range of factors including brand, operating temperature, and damage.

3. Re-pair your remote to the TV

Over time, your remote can become unpaired with your TV. Pairing is the term for your remote and TV being linked together, so your TV knows which remote to respond to.

Check The Batteries of Samsung TV Remote

Don’t get frustrated when your remote control stops working. Before you start looking for a replacement, check the batteries in your Samsung remote control.

Ensure that Remote Control Sensor is Unobstructed

If you’re having trouble with your Samsung TV turning on, try moving the device and the remote to different areas in the room. If moving them around doesn’t solve the problem, you may have an obstruction between the remote control sensor on your TV and its remote (the IR receiver).

Ensure That Remote is paired

The new “smart” remote control can sometimes be a bit finicky. Sometimes it works, and other times it won’t — and we can’t really figure out why. If you’re having trouble pairing the remote to the TV, make sure your TV is on and working, then try re-pairing the remote again after waiting a few minutes.

Reduce Distance between Remote and TV Sensor

Samsung remote controls have their limitations — the maximum distance at which they can be used is 30 feet (10m), which may not be far enough for some people.

Remove Any Devices that can cause Interference

Samsung TVs are likely to run into interference with other remotes. Due to the technological limitations of infrared (IR) remote controls, your Samsung TV remote control may not function at times.

Disable Bluetooth

If you’re pairing your remote via Bluetooth, ensure that you turn it off and then turn on the Bluetooth. Ensure there is no obstruction between your TV and remote. Walls, electromagnetic devices, and other electronics can interfere with the infrared signal.

Perform a Hard Reset of the Remote

o reset your remote control, you need to remove the batteries from the device and unplug the power cord from the outlet for 60 seconds. First, locate the batteries and then locate the remote’s battery area. Remove both batteries from your remote and insert them back into the remote after 60 seconds.

Samsung Remote Keeps Saying Not Available

When you try to connect your remote to your TV, you will go through the process of pairing, which was mentioned earlier, and once this is done, you should visit the successful pair. If you connect your remote control properly But you have to face the message that the remote is not available.

Samsung TV Remote Power Button Not Working

Just as important as the ability to change channels on your Samsung TV is the ability to turn your Samsung TV on and off. This allows users to be able to control their TV from where they are sitting or standing. But it is also a must-have, for any Affiliate, promoting any program.

Samsung TV Remote Sensor Not Working

The sensor on the remote of your Samsung TV is a connecting piece with the ability of your remote to control your TV. If this sensor does not work, there is no way you can control your TV from this device. When the sensor suddenly stops working, it is a frustrating thing.

Samsung TV Remote Pointer Not Working

It can be very frustrating when you watch your favorite movie or show but notice that the pointer on your remote control is not working. A no pointer on a remote is one that relays a signal from your remote directly to your TV, so it works properly for the remote to work at its full potential.

What If Your Remote Is Blinking Red Light?

When your Samsung TV remote doesn’t work and starts flashing red, you can try to fix it in many ways.