- Remove the power from your whirlpool dryer.
- Remove the vent from the back of the dryer.
- Reach behind the dryer.
- Remove all screws on the back of the dryer.
- Remove the back panel to access the element.
- Disconnect the wiring harness from the components to reach the element housing. (If necessary, label the wires to retouch correctly)
- Remove the screws holding the heating element housing.
- Slide the faulty heating element housing downward and outward.
- Slide the new heating element back.
- Attach it with the screws you just removed.
- Retouch the wires to the components.
- Place the back panel in the back and secure it with the screws provided.
- Reattach vent behind dryer.
- Slide dryer back into place.
- Plug in the dryer and run a test to see if the dryer is heating up now.
Full Answer
How to troubleshoot Whirlpool dryer problems and repairs?
Whirlpool Duet Dryer troubleshooting
- Dryer still Beep. This is a simple problem and easy to solve within a few minutes. ...
- Auto shut off. It is another troubleshooting problem when you start the dryer it makes a noise in a heavy voice and automatic shutoff after a few minutes.
- Dryer not spin but properly heated. ...
- Overheating Problem. ...
How to repair a whirlpool dryer with a bad timer?
Use the flathead screwdriver to pry open a tab that holds a power source harness to the rear of the timer. Remove the timer knob, the two screws that hold the timer in place, and pull the old timer out. Replace the old timer with the new timer. Replace all other connectors and wire harnesses. After installing the new timer, replace the rear panel.
Why would a whirlpool dryer stop working?
Whirlpool Dryer Not Running Repair Guide
- Disconnect the power to the dryer.
- Locate the start switch by removing the back of the control panel.
- Disconnect the wires off the start switch.
- Place the leads of your ohmmeter across the two wire terminals on the switch.
- Test for continuity while you have someone press (or turn) the start switch.
How do you fix a whirlpool dryer?
These errors also indicate that there is a problem with one of the parts:
- Turn off the dryer and unplug it.
- Wait for about one hour.
- Reinsert the connector and restart the dryer.
What causes a Whirlpool dryer to stop working?
If there is a part malfunction when your dryer isn't drying clothes a blown thermal fuse is often the cause. A dryer's thermal fuse will trip to prevent the dryer from overheating, cutting power to the dryer. While a thermal fuse can malfunction over time, clogged dryer vents are a common trigger that blows the fuse.
How do you troubleshoot a Whirlpool dryer?
7:579:19Whirlpool Dryer Not Heating - Diagnosing Common IssuesYouTubeStart of suggested clipEnd of suggested clipYou've also got the timer again you're gonna look for the black and red typically pull it away checkMoreYou've also got the timer again you're gonna look for the black and red typically pull it away check for the closed circuit then that will eliminate the timer is the problem.
How do you service a Whirlpool dryer?
0:0610:49Whirlpool Dryer Repair – How to replace the Maintenance KitYouTubeStart of suggested clipEnd of suggested clipSet those aside main top is held to the cabinet with a couple of clips at the front you can eitherMoreSet those aside main top is held to the cabinet with a couple of clips at the front you can either access them with a putty knife.
Is there a reset button on Whirlpool dryer?
Whirlpool dryers can do many things, such as monitor moisture levels and temperature, reduce noise, periodically tumble clothes to remove wrinkles, steam clothes and adjust the overall drying time according to fabric and load size. However, one thing a Whirlpool dryer cannot do is reset itself by pushing a button.
How do you diagnose a dryer problem?
0:5136:35Dryer Troubleshooting - Top 10 Dryer Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt could be caused by a rattling vent in the back. If it's not connected securely. Sometimes thisMoreIt could be caused by a rattling vent in the back. If it's not connected securely. Sometimes this can rattle and make a noise that way other times the rollers. If they're not spinning.
How do I know if my Whirlpool dryer thermal fuse is blown?
1:042:10Dryer Not Heating? Thermal Fuse Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the needle does not move or the digital display does not change significantly. There is noMoreIf the needle does not move or the digital display does not change significantly. There is no continuity. Which means the fuse has blown out and will need to be replaced.
Where is the filter on a Whirlpool dryer?
0:003:15Whirlpool Dryer - How To Clean Lint Filters - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt all right even on the back side if you see lint on the back side remove that. All right and thenMoreIt all right even on the back side if you see lint on the back side remove that. All right and then shut it back. And it locks kind of into place like with this little knob right here.
How long does a Whirlpool clothes dryer last?
Generally, Whirlpool dryers have a lifespan of 8-12 years. However, some may last longer if you maintain it properly. But if your Whirlpool dryer is at least ten years old, replacing it is more reasonable. Repairing the 10-year-old dryer will likely cost less.
How do I clean the inside of my dryer vent?
How to Clean Out a Dryer Vent in 7 Simple StepsGather Your Cleaning Supplies. ... Pull the Dryer Out From the Wall, Unplug It, and Disconnect the Duct. ... Vacuum the Inside of the Vent. ... Connect the Flexible Rods in Your Dryer Duct Cleaning Kit to Your Power Drill. ... Turn On the Drill and Let the Brush Work Its Magic.More items...•
Does unplugging a dryer reset it?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That's it. That's all it takes to reset.
When I press the start button on my dryer nothing happens?
Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to-start switch can prevent the motor from running. Use a multimeter to check for continuity through the push-to-start switch.
Why would a dryer just stopped working?
A dryer needs to be plugged in to run. Check the outlet first and make sure that the dryer is securely plugged in. Also, if an electric dryer stopped working, it could be because of outlet damage or a tripped fuse.
When I press the start button on my dryer nothing happens?
Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to-start switch can prevent the motor from running. Use a multimeter to check for continuity through the push-to-start switch.
Why won't my dryer start all of a sudden?
The first issue to check for when a dryer won't start is whether the power cord is properly plugged in, directly connected, or showing signs of serious damage. Also, a dryer requires a lot of electricity to operate, so it may have tripped the breaker when pulling the necessary power.
How do I reset my dryer?
1:092:47Dryer / washer not working. How to reset dryer / washer electronically.YouTubeStart of suggested clipEnd of suggested clipAnd they're gonna fry if you do leave it unplugged for one minute. That's it plug it back in andMoreAnd they're gonna fry if you do leave it unplugged for one minute. That's it plug it back in and then. Once you plug it back in open. And close the door. Six times within 12 seconds.
Why does my dryer just beep and not start?
Dryer Beeps Continuously Unfortunately, the beeping is a result of a bad control panel. Unplugging or resetting the dryer will not solve the problem. The board will need to be replaced. If you are handy with tools and electronics, you can avoid a service call if you do the work yourself to solve the beeping.
How to access thermistor on a dryer?
For easy access to the thermistor, you’ll need to remove the dryer’s front bulkhead. To do so, unthread the screws that go to the control housing bracket. Then, take out the screws securing the front of the control board bracket to the dryer cabinet. Next, create support for the bracket by tying it to the side of your appliance.
What does a blower wheel do?
The Blower Wheel and the drive motor function together to pull air into the appliance’s drum and to push air out of the dryer through an exhaust vent. If the blower wheel is defective, and the hot air in the appliance is not circulating, the temperature inside your dryer cabinet can reach dangerous levels.
How to get rid of lint in dryer vent?
If you find excessive lint in the lint trap housing or in the vent tube, use either a lint brush or your vacuum cleaner to get rid of it. After you’ve removed the lint obstruction from your dryer’s venting system, your appliance should no longer overheat.
What happens if your dryer is too hot?
A higher than normal temperature in your appliance is a safety hazard that can lead to your dryer and your home catching fire. Before you begin inspecting your appliance, allow it to cool down; otherwise, you may end up burning yourself as you examine its components. There are several parts in your dryer that can malfunction ...
Why does my dryer overheat?
Due to years of wear and tear, the seal can become damaged. Unfortunately, when this happens, hot air can leak into the dryer cabinet which will cause the appliance to overheat . The Heating Element in your dryer heats up the air before it travels into the dryer drum.
How do I take the front panel off a dryer?
To take the dryer’s front panel off, you’ll need to tilt the appliance back slightly and slip an object, such as a block of wood, underneath the front, bottom edge of the dryer. With the appliance raised, you can unthread the bottom screws that secure the panel to the machine.
How to disconnect moisture sensor from dryer?
Locate the moisture sensor wire harness and pull the wires apart to disconnect them. Move to the bottom of your appliance, and take out the screw that supports the bulkhead’s lower retaining bracket. Then remove the screws securing the bulkhead to the dryer’s frame.
Whirlpool Dryer Troubleshooting Codes
If a code beginning with an “F” appears in the display, alternating between F# and E#, the dryer control has detected a problem.
How to Clean the Lint Screen in Whirlpool Dryer
A screen blocked by lint can increase drying time. The lint screen is located in the door opening of the dryer. There is a “Check Lint” or “Check Lint Screen” indicator light on the control panel to remind you to clean the lint screen before each load. The light will turn off once the door is opened or a cycle is started.
Whirlpool Dryer Not Heating Up
If your Whirlpool dryer is not heating, it could be because of a number of reasons:
Why is my Whirlpool Dryer Wrinkling Clothing
If your clothes are getting wrinkled, it could be because the load was removed from the dryer at the end of the cycle. You need to select the Steam Refresh cycle to tumble the load with water and heat.
Whirlpool Gas Dryer Not Drying Completely
If clothes are not drying completely, drying times are too long, or the load is too hot, follow these instructions to troubleshoot:
Whirlpool Duet Dryer Beeps 3 Times
3 beeps means that the dryer has detected that the door is open. Make sure that the door is closed firmly. Try the following instructions if the problem persists:
Whirlpool Dryer Odors
If there are some odors in your dryer, it could be caused by the following:
What happens if a multimeter needle does not move?
If the multimeter display needle does not move or change, there is no continuity and the thermostat should be replaced. Thermostats should show continuity at room temperature and should shut off when heated up. If it doesn’t turn off when heated, the dryer could overheat and increase the chance of a home fire.
What happens if a Whirlpool dryer doesn't turn off?
If it doesn’t turn off when heated, the dryer could overheat and increase the chance of a home fire. If the thermostat didn’t test well for continuity, replace it. It’s an inexpensive repair and shouldn’t take longer than 15 minutes to complete. Here’s how to access the thermostat on your Whirlpool Dryer.
What happens if a multimeter reads zero ohms of resistance?
If the multimeter reads zero ohms of resistance, the thermal fuse has continuity. If the multimeter display needle does not move or change, there is no continuity and the thermal fuse should be replaced. You won’t be able to determine if a thermal fuse has failed by simply looking at it.
What is the most important tool in appliance repair?
The multimeter is the most important tool in an appliance repair toolkit. Give particular consideration on how to check for continuity. In reference to electrical components, continuity is simply the unbroken flow of electricity from its power source and distributed through the appliance components. A break in continuity in any part of the ...
What does it mean when a dryer breaks in continuity?
A break in continuity in any part of the electrical system would indicate that electrical current is not flowing to that component. The good news is that if you do find a break in continuity you will usually have found the part that needs to be repaired or replaced. Unplug the dryer before beginning any work.
What happens if a dryer doesn't shut off?
If it doesn’t shut off when heated, the dryer itself could overheat, increasing the chance of a home fire.
What happens if a washer leaks?
If the washer is leaking, some of that water could have invaded the dryer and become the source of moisture. Asking these questions may seem redundant but could save John the expense of an unnecessary service call. Let’s assume that John’s dryer runs but does not heat up.
