Necklace Barrel Clasp Repair
- Necklace Barrel Clasp Repair. Locate the broken part of the ring that attaches through the back of the barrel clasp. ...
- Plug in the electric soldering iron and set the solder temperature to the degrees that suits the melting point of both the soldering wire and the barrel clasp.
- Molten metal is extremely hot and will cause severe burns. Handle the soldering gun with care and keep your distance from the melting metal.
- Attach the barrel clasp necklace back together and hold each end of the necklace taught to test the solder strength.
How to replace a broken necklace clasp?
Jewelry Clasp Types
- Spring Ring Clasp. These bits of gold chain have attached spring ring clasps. ...
- Lobster Clasp. This gold chain necklace is fastened with a lobster clasp. ...
- Toggle Clasp. This gold chain bracelet has a jeweled toggle clasp. ...
- Box Clasp. This gold rope chain was changed from a lobster clasp to a box clasp. ...
- Bolo Clasp. An evil eye bracelet with a bolo clasp. ...
How to repair jewelry clasp?
What Are the Steps to Jewelry Repair?
- Lobster clasp repair: Realign the hook and latch of a bent clasp by carefully moving them with needle-nose pliers until the parts meet.
- Fold-over clasp repair: Bend the tab back onto itself if the clasp doesn’t snap closed. ...
- Spring-ring clasp repair: Remove the ring by opening the loop holding the spring ring to the jewelry piece. ...
How to repair a broken necklace?
- Catch replaced
- Chain repair
- Charm soldering
- Clasp repair
- Leather bracelet repair
- Soldering
How do you fix a necklace?
How to Get Kinks Out of Gold Chains
- Lay a thin microfiber cloth on a flat surface such as a table or countertop.
- Unhook the necklace and stretch it out to its full length. Examine the chain carefully to determine where the kink is located.
- Dab your middle and index fingers with baby oil. ...
- Work the crease out of the necklace using your fingers. ...
How do you reattach a necklace clasp?
1:152:20How-to: Attach or Replace a Clasp - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen I'm gonna go in with the other jump ring open it up again and slide it on the other. Side. TakeMoreThen I'm gonna go in with the other jump ring open it up again and slide it on the other. Side. Take both of my pliers. And I like to wiggle a little bit and snug it right up.
How do you fix a broken necklace clip?
0:291:34How to Fix a Clasp - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what we're gonna do is we're going to take a simple tap. And we're gonna actually open up thatMoreSo what we're gonna do is we're going to take a simple tap. And we're gonna actually open up that area. So what we're gonna do is I'm going to take the tack I'm gonna apply a little bit of pressure.
How much does it cost to fix a clasp on a necklace?
Replacing a Clasp: $65-$250+ Depending on the style, the size, and the type of metal the clasp is made of, this can cost you between $65 and $250. To give you a better idea of what your clasp replacement might cost, a standard gold 5 mm spring ring clasp can cost $30.
How do you fix a chain necklace hook?
1:2812:38How to Fix Broken Chain Necklaces jpg - YouTubeYouTubeStart of suggested clipEnd of suggested clipTaking it past the point where you think it's close tight and it'll kind of spring back in placeMoreTaking it past the point where you think it's close tight and it'll kind of spring back in place that addition of a jump ring then will allow you to either add your new clasp.
How do you fix a broken locket clasp?
Use a little bit of bluetac to keep it closed. This will let you open and close the locket but be prepared for it to fall open occasionally, especially as the bluetac gets older. Glue it closed with araldite, superglue or jewellery glue.
How do you fix a broken metal necklace?
0:406:13How to FIX a BROKEN CHAIN NECKLACE ( DIY Jewellery Repair )YouTubeStart of suggested clipEnd of suggested clipIf you use something too big it doesn't look right if you use something too small. It doesn't lookMoreIf you use something too big it doesn't look right if you use something too small. It doesn't look right and also it is not strong enough to hold a chain plus a pendant. Amount the right diameter jump
What is the clasp on the necklace called?
Hook and Eye Clasp - The easiest and simplest clasp, containing two pieces; one is a hook and the other a circle. The hook slips into the circle to secure the necklace in place.
What is a lobster clasp on a necklace?
A lobster clasp, also known as a lobster hook, is a fastener that is held closed by a spring. The lobster clasp is opened or closed by holding a small lever, usually with a fingernail, long enough to apply, then it is attached (or removed from) a short link-chain or a ring-like structure.
What is a spring ring clasp on a necklace?
0:131:16Spring Rings for Finishing Chain - YouTubeYouTubeStart of suggested clipEnd of suggested clipEach spring ring features an open attachment ring for finishing the end of your necklace. Each claspMoreEach spring ring features an open attachment ring for finishing the end of your necklace. Each clasp is also marked with a quality stamp that specifies the metal.
How do you fix a clasp on a necklace that won't open?
Use the knife with your dominate hand. Insert the tip of the knife into the side of the clasp and gently twist the knife to increase the distance between the top and bottom of the clasp. Open and close the clasp after each twist to check if it is working properly. Go slowly and gently with this repair.
How do you keep a necklace clasp in place?
If Your Clasp Keeps Twisting Around to the Front To prevent this from happening, look for a necklace that has a counterweight on the clasp, or add one yourself. A counterweight can be anything from a charm, metal ball, or bead that is attached to the clasp.
How do you attach a clasp to a thin chain?
0:301:43Adding a Clasp to Thin Chain with a Head Pin - Quick Tip, Beaducation ...YouTubeStart of suggested clipEnd of suggested clipTake my chain nose plier open that up there. Add my clasp pop it on here to the chain. Take my chainMoreTake my chain nose plier open that up there. Add my clasp pop it on here to the chain. Take my chain nose plier. Again.
How do you solder a necklace clasp?
0:564:33How to Make Soldered Jewelry, Episode #7 - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this will be the end that a clasp will come into and clamp into okay first I'm gonna come in withMoreSo this will be the end that a clasp will come into and clamp into okay first I'm gonna come in with my torch again it's pretty low not too high. And apply some flux.
How do you keep a necklace clasp in place?
If Your Clasp Keeps Twisting Around to the Front To prevent this from happening, look for a necklace that has a counterweight on the clasp, or add one yourself. A counterweight can be anything from a charm, metal ball, or bead that is attached to the clasp.
How do you put a hook on a necklace?
To form the hook into a loop, grip just before the tip with your chain nose pliers and using a combination of moving the pliers and either your finger or the table underneath to help form it into a teardrop shape.
How do you attach a clasp to a thin chain?
0:301:43Adding a Clasp to Thin Chain with a Head Pin - Quick Tip, Beaducation ...YouTubeStart of suggested clipEnd of suggested clipTake my chain nose plier open that up there. Add my clasp pop it on here to the chain. Take my chainMoreTake my chain nose plier open that up there. Add my clasp pop it on here to the chain. Take my chain nose plier. Again.
What is toggle clasp?
The toggle clasp is markedly different from the lobster and the spring ring clasps in design. A thick hoop and a long bar are attached to opposite ends of the chain, and the long bar is vertically tucked through the hoop. Once it’s through, the horizontal orientation of the bar prevents it from slipping out of the hoop, locking the chain.
What is a clasp in jewelry?
Jewelry Clasp Types. 1. Spring Ring Clasp. These bits of gold chain have attached spring ring clasps. The most common and classic one out of all the jewelry clasp types, a spring ring clasp consists of a little wire tucked inside a hollow hoop.
How does a bolo work?
The two ends of a chain are drawn through the bolo, and moving the bolo up and down shortens and lengthens the piece. While the clasp itself is very sturdy, items that have thinner chains are prone to breaking from pulling the bolo.
What is evil eye bracelet?
An evil eye bracelet with a bolo clasp. The fifth type of clasp is most commonly seen on bracelets. Unlike the other clasps, the bolo is designed to be adjustable; its sliding mechanism allows for the wearer to change the size of their jewelry. The two ends of a chain are drawn through the bolo, and moving the bolo up and down shortens ...
What to do if a spring ring is broken?
When a spring ring clasp is broken, the jeweler can either repair it or replace it. The most common repair is bending the little wire back into the hoop, when a bad tug pulls it out. If the entire hoop has been crushed, the jeweler replaces it, as there is no way to fix the damage. 2. Lobster Clasp.
What does a lever do on a necklace?
When you pull the tiny lever backwards, it moves the wire into the hoop, leaving behind an empty gap so you can hook the other end of the chain into the clasp . Releasing the lever allows the wire to spring back, securing the piece of jewelry. The design is discreet, making it an excellent choice for thin and delicate necklaces.
Can a jeweler bend a lever back into shape?
With a pair of pliers, the jeweler can bend it back into shape. On occasion, the lever may get stuck, and the repair for that kind of damage is variable- sometimes the jeweler will not be able to fix it, requiring a replacement. 3. Toggle Clasp. This gold chain bracelet has a jeweled toggle clasp.
Introduction
Barrel clasps are on many pieces of jewelry, but there are only guides available on how to replace the clasp—not how to repair it. Taking a broken necklace to a jeweler or completely replacing the clasp can be expensive and time-consuming.
Step 1 Necklace Barrel Clasp Repair
Locate the broken part of the ring that attaches through the back of the barrel clasp.
Step 2
Plug in the electric soldering iron and set the solder temperature to the degrees that suits the melting point of both the soldering wire and the barrel clasp.
How do lobster clasps work?
Lobster clasps are spring-loaded, but open by pushing down on the clasp. Their shape resembles a lobster claw. If the clasp is connected to the necklace by a jump ring, it is easy to replace. If the clasp is soldered on, you will need professional help. Buy a replacement clasp.
What to do if your bracelet clasp is broken?
If your favorite necklace or bracelet has a broken clasp, don't leave it languishing in your jewelry box. For most types of clasps, it is an easy matter to replace the broken clasp with a new one. Check that the actual clasp is broken.
How to open a jump ring?
Open the jump ring by twisting it, not spreading it. Spreading will weaken the ring. Attach the new clasp. Hook the new clasp through the jump ring and twist the jump ring closed. Make sure the jump ring is closed tightly, or the clasp may slip off through the gap. Repeat for the other end of the jewelry.
Why does my clasp fall off?
Many times, a clasp will fall off because the jump ring (a simple metal ring with a small cut on one side) has broken or stretched open. Replace a broken jump ring or crimp a loose ring closed. Identify the broken clasp type. There are several varieties.
What is magnetic clasp?
Magnetic clasps, where two opposite magnets are attached to each end of the necklace, are easy to use, but not all provide excellent holding strength. Test the strength before attaching to your jewelry.
How to prevent tangled chain?
The easiest way to prevent tangled chains and knots from happening is to hang your chain jewelry instead of piling the links on top of one another in a box or on your dressing table. But once the knot or tangle is there—what do you do?
What to use to fix a ring that is too small?
Both of these are easily fixed with a metal ring mandrel and a leather mallet.
Why does my necklace break at the clasp?
Many necklaces break at the clasp because it sees the most use . There are two typical problems, a jump ring opens and part of the clasp gets lost or the spring clasp gets broken and no longer closes correctly. For both problems, the solution is the same. You need to replace the broken clasp with a new one.
How to make a ring larger?
To make the ring larger, you will continue tapping, rotating around the ring until it moves to the desired size on the ring mandrel. Note that re-sizing or re-shaping fine jewelry or rings with stones should only be done by professionals to avoid loosening stone settings or causing a stress fracture in the metal.
Can you loosen crimp beads?
Beading wire can loosen from the crimp beads that secure it to the clasp or break from abrasion and wear. When this happens, you will need to restring the necklace and attach the clasp using new crimp beads. This is one of the harder simple repairs, only because working with crimp beads can be difficult for new jewelry makers.
How to reshape a ring with a mallet?
Tap gently on the side with the mallet, gently pushing the ring down. Repeat on the other side by removing the ring and flipping it over. To re-shape a ring, you only want to apply enough pressure to make the ring round again.
Can you flatten crimps with a flat plier?
You can flatten crimps with flat-nosed pliers, but for a professional finish, special crimping pliers will make the job easy and give longer-lasting and beautiful results. 03 of 07.
