
Peerless Faucet Repair Instructions
- Step 1. Turn the water valve under the sink to the closed position. Sorry, the video player failed to load.
- Step 2. Take off the handle to the Peerless faucet by removing the screw at the bottom of the handle with an Allen...
- Step 3. Use pliers or the tip of a screwdriver to push the plastic washer under the handle (now on top of the...
How to replace a kitchen faucet with two handles?
- Switch off the water supply valve
- A decorative cap hides the bolt that holds the handle to the faucet. ...
- Unscrew the bolt using a screwdriver.
- Take off the nob so that you can reach the valve stem.
- Where you have taken the knob off, replace it with a new one. ...
- Insert the large screw into the knob and start screwing it using a screwdriver.
How to stop a peerless faucet from dripping?
- If the handle has a cap, remove it with a flat head screwdriver. Use a Phillips screwdriver to unscrew the handle.
- Remove the faceplate behind the handle from the shower wall. ...
- Find the metal sleeve over the shower valve. ...
- If the shower valve has a locking clip, pry it off with needle nose pliers or a screwdriver.
How to replace a diverter valve in a peerless faucet?
Two-Handled Faucet Diverter
- Reach under the sink to rotate the hot and cold water supply valve clockwise. ...
- Place a rag over the cap behind the two-handled faucet spout. ...
- Insert a butter knife or a nickel into the slot at the top of the diverter. ...
- Wrap the clean diverter threads in one or two layers of thread-seal tape. ...
- Replace the faucet cap on the faucet body. ...
How to disassemble a peerless kitchen faucet?
- Turn off the water shutoff valves under the sink and open the faucet to drain water.
- Unscrew the handle retaining screw underneath the lever with a 1/8-inch Allen wrench.
- Wrap a rubber glove around the metal collar that holds the valve in place and grip the collar with adjustable pliers.

How do you fix a dripping Peerless Faucet?
What do I do if my single-handle kitchen or lavatory faucet drips from the aerator?Remove the aerator (it should twist off by hand).Turn off the water supplies.Turn the faucet handle to the "on" position.Turn the water on at the supply.Flush the faucet and supply lines for one minute.More items...
How do I fix my Delta Peerless Faucet?
0:004:37Delta Peerless Bathroom Single Handle Faucet Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd how to replace the washer and seats turn off the shut-off valves to the faucet. And then closeMoreAnd how to replace the washer and seats turn off the shut-off valves to the faucet. And then close the stopper or put a rag down so none of the parts fall into the drain.
How do you tighten a peerless faucet?
Use pliers or the tip of a screwdriver to push the plastic washer under the handle (now on top of the faucet head) left to loosen it. Then push it back right to tighten it, reassemble the faucet and test it.
How do I know what model my Peerless Faucet is?
Your faucet's model number may be found on the packaging, and also on the Installation instructions provided with your faucet.
How do you remove a peerless faucet stem?
1:025:31Delta/Peerless Faucet Cartridge Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn it off by turning these a quarter of a turn. We turn off both sides. Because water can flowMoreTurn it off by turning these a quarter of a turn. We turn off both sides. Because water can flow from one side of the other when you take this assembly apart.
How do you remove a peerless faucet handle without a visible allen screw?
If the set screw is visible, hold the faucet in place and tighten the screw. If you can't see the screw, it will be under the cap, which you can remove with a flathead screwdriver or your small knife. Tighten the screw while holding the handle in place. Once the screw is tight, the handle should stop shaking.
Why is my peerless faucet dripping?
If your Peerless faucet is leaking from under the handle, it's usually because the retaining nut holding the cartridge or ball valve is loose. Luckily it can be fixed in a couple of simple steps: To access it, you have to remove the handle and the dome-shaped collar. Then, you can tighten it with pliers.
Do they still make Peerless faucets?
Some Peerless faucets are still manufactured in Delta's North American plants. Masco is one American faucet manufacturer that has resisted exporting all of its manufacturing to China. Delta makes faucets in Greensburg, Indiana; Jackson, Tennessee; and Morgantown, Kentucky.
How do you take apart a single handle bathroom faucet?
1:204:00How to Replace the Seats & Springs in a Single Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the needle nose pliers to unscrew the adjusting ring. Place a cloth over top and use the channelMoreUse the needle nose pliers to unscrew the adjusting ring. Place a cloth over top and use the channel lock pliers to unscrew the cap. Now pull out the ball the cam and packing.
Does Peerless have a lifetime warranty?
You're probably wondering about the "limited" part of that warranty, aren't you? Our Lifetime Limited Warranty applies to Peerless faucets manufactured after January 1, 1995. And it's one of the most extensive in the industry (provided you are the original purchaser).
Are Delta and Peerless faucets the same?
Peerless bathroom and kitchen faucets can be found at FaucetDirect.com. Peerless is a proud partner of the Delta Faucet brand of plumbing products. And with this name and reputation of innovation behind them, you can be confident that Peerless faucets are just as reliable and durable as every other Delta brand faucet.
Where do I find my faucet model number?
Identifying Your Faucet ModelThe model number is printed on a tag that is attached to the cold water supply line of the faucet.The supply line is located below the sink, countertop, bath rim, or behind the bowl of a bidet.The model number, or part number, is typically preceded by "P/N."More items...
How do I know if my faucet cartridge is bad?
Signs that a cartridge faucet needs repair are water dripping from the spout, difficulty in adjusting the water temperature, hot water entering cold water outlets like toilet supply lines and inadequately heated water at some faucets.
How do you fix a Delta single handle kitchen faucet?
1:078:56Delta Kitchen Faucet Leak Repair (Single Handle) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a double check to make sure that your water is off use a 1 8 inch hex head wrench to removeMoreThis is a double check to make sure that your water is off use a 1 8 inch hex head wrench to remove the set screw in the handle. Put the set screw in a parts pole to ensure that you will not lose.
How do you change a stem assembly on a Delta faucet?
1:493:15How To Fix A Leaky Delta Two Handle Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut the bonnet nut on over the cartridge and hand tighten it use the pliers or wrench to Snug it upMorePut the bonnet nut on over the cartridge and hand tighten it use the pliers or wrench to Snug it up but do not over tighten. Now reassemble the parts of the faucet handle.
How do you fix a kitchen faucet that won't swivel?
1:424:26Archive - How to Keep Kitchen Faucet Rotating Smoothly - YouTubeYouTubeStart of suggested clipEnd of suggested clipSet it aside. And now I've exposed the top and the lower row rings which allows your faucet toMoreSet it aside. And now I've exposed the top and the lower row rings which allows your faucet to swivel those are the Rings we're going to grease grabbing my silicon lubricant.
What do I need to repair a peerless faucet?
Things You'll Need. Allen wrench. Pliers or wrench. Towel. Replacement ball valve for Peerless faucets. To repair a Peerless faucets, you will use the same process used for several similar faucets made by other manufacturers. You will partially disassemble the faucet, so it helps to have some experience taking things apart.
How do I fix a leaky faucet?
Use pliers or the tip of a screwdriver to push the plastic washer under the handle (now on top of the faucet head) left to loosen it. Then push it back right to tighten it, reassemble the faucet and test it. This will correct leaks in some cases. If the leak persists, move on to the next step.
How to remove a bonnet nut from a faucet?
Loosen the bonnet nut (small dome-shaped nut) on the faucet head with a pair of pliers. Drape a towel over the nut before gripping it with pliers to avoid scratching the part. Remove the nut after you loosen it.
What is a peerless faucet?
Peerless faucets represent the low end of Masco's faucet line, and Peerless faucet reviews, including the one from Starcraft Custom Builders, are generally lukewarm due to their predominantly plastic construction and utilitarian appearance. However, what they lack in style, they make up in design simplicity and repairability, ...
What is the advantage of peerless faucets?
One of the advantages of choosing a budget faucet, such as a Peerless, is the ready availability of such parts, which come in model-specific repair kits, . And if your Peerless faucet is leaking, you'll probably need one of these kits. Advertisement.
What to do if aerator doesn't work?
Scale can also clog the valve, so if cleaning the aerator doesn't work, try removing the valve and soaking it in vinegar. If the faucet has a cartridge valve, and the valve is clogged with limescale, you may have a hard time removing it.
How to stop a faucet from leaking?
Finally, if the faucet is leaking from the handle, you can usually stop the leak by tightening the valve retaining nut.
Is it expensive to replace gaskets?
The parts aren't expensive , and replacing all of them, especially the gaskets, O-rings and springs, is the surest way to guarantee a successful repair. Advertisement.
Do Delta faucets have ball valves?
This could account for the large number of ball-valve models available, as ball valves are a feature of Delta faucets. Besides ball valves, a significant number of Peerless faucets have cartridge valves, particularly double-handled widespread models and tub-and-shower faucets.
Techniques for solving a tough faucet problem
Repair a drippy ball-type faucet using these pro tricks to deal with stubborn screws. You may have to replace the handle, but not the entire faucet.
Kitchen Faucet Repair: Loosen a stuck screw on a single-handle faucet
If the Allen screw is stuck, or if you strip it so it won’t come out, remove the cap with the handle still in place. You can’t grab the flattened edges with the handle in place. Instead, for this kitchen faucet repair, cushion the jaws of pliers and grip the round edge below.
How to Remove Faucet Handle
If you can’t loosen the Allen screw on the handle of a ball-type faucet, don’t let that 15¢ screw force you into a $100 faucet replacement… just yet! Normally you have to remove the handle to get the worn rubber seats that cause the drip (Figure A). First try spraying the screw with penetrating oil every day for a week.
Required Tools for this kitchen faucet repair Project
Have the necessary tools for this DIY kitchen faucet repair project lined up before you start—you’ll save time and frustration.
Required Materials for this kitchen faucet repair Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
