Cut the damaged section of PEX pipe on a 90-degree angle and remove it, using a PEX cutter. Step 2 Slide a crimp ring over the end of each side of the removed damaged area. Slide the ring onto the pipe so it is at least 2 inches from the end.
Full Answer
How do you fix PEX that has been damaged?
REPAIRING DAMAGED PEX 1-800-716-340661 PEX COMPRESSION REPAIR COUPLING Making the repair: STEP 1 Start by cutting out the damaged piece of PEX, make sure the cut is square using a suitable tubing cutter. STEP 2–3 After cutting the tubing, slide the nut then the compression ring onto each tubing end.
Can you cut PEX pipe on a 90 degree angle?
Use a PEX cutter to cut PEX pipe on a 90-degree angle. PEX pipe is a flexible plastic tubing product used for supplying water in buildings. It is made from cross-linked polyethylene. PEX pipe can become damaged during installation, from freezing or other unforeseen events.
How do you attach PEX fittings to PEX pipe?
Press a straight insert fitting into each side of the damaged area that was removed until the fitting is pushed into the pipe as far as it will go. Slide the crimp ring over the end of the pipe and fitting until it is aligned over both the PEX tubing and fitting.
How do you cut PEX tubing to size?
STEP 1 Start by making a square cut at the end of the tube using a suitable tubing cutter. If PEX-AL-PEX tubing is used, also ream the tubing using our reaming tool. STEP 2 After reaming the tubing, push the tubing into the fitting making sure that the tubing seat all the way at the bottom.
Can PEX tubing be repaired?
Repairing PEX Tubing Much like installing PEX tubing, repairing it is also an easy process. If you're using a crimp or clamp connection systems (both being very popular), using brass PEX fittings with copper or stainless steel crimp rings is the most inexpensive method of repairing PEX tubing.
How do you fix a leaking PEX joint?
0:282:05Leaking PEX Pipes : Plumbing Help - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this tool right here has different sizes on there so whatever size pipe that you have you'll takeMoreSo this tool right here has different sizes on there so whatever size pipe that you have you'll take and place this right over the ring. And a lot of times these pecs crimpers adjust themselves so
Can you're crimp PEX fittings?
When done correctly, it's possible to reuse PEX fittings after the copper crimp rings have been removed.
Why do my PEX fittings leak?
The leaching of zinc also makes the fittings weaker, resulting in dezincification. In PEX pipes, the zinc build-up can cause your kitchen and bathroom fixtures to clog. It also causes fittings to crack or break, leaking water within your walls or underneath your house.
How do you splice PEX?
7:089:37How to join pex (plastic pipe) five different ways. Plumbing Tips!YouTubeStart of suggested clipEnd of suggested clipAnd it's quite simple as far as how it works there's holes in here you push the plastic on. And you'MoreAnd it's quite simple as far as how it works there's holes in here you push the plastic on. And you'll see that okay the plastic has gone all the way into the fitting.
How do you check for PEX leaks?
10:1217:25Skoolie Plumbing: Pex Pressure Test - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd see if make sure there's no leaks anywhere. So here we go we should be able to hear a hissing.MoreAnd see if make sure there's no leaks anywhere. So here we go we should be able to hear a hissing. Sound. If there's a leak.
Can PEX push fittings be reused?
In case of PEX, only use a PEX pipe cutter. Always make a clean, square cut. Avoid reusing push fittings. The O-ring inside the fitting has a food grade lubricant applied to it, which is gradually wiped off when pipe is removed and re-inserted or fitting is re-used.
Can I crimp PEX with pliers?
You should use a crimping tool that crimps the PEX. Good luck with the crimping. The tool can be rented or purchased. Diagonal cutting pliers or end cutting pliers can be used to cut the clamps.
Can you crimp PEX without tool?
1:413:14Shark bite clamps and How to crimp pex connections without crimp tool!YouTubeStart of suggested clipEnd of suggested clipAnd as you can see work perfectly so if you want to do this without buying the hundred dollar toolMoreAnd as you can see work perfectly so if you want to do this without buying the hundred dollar tool and just use a pair of diagonal cutters to crimp into this little guy here.
How do you repair a PEX fitting?
0:302:28How to Fix Pex A and Pex B - 2 Different Ways - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you just take a heat gun to it leave it there and give it even heat distribution it'll fix itselfMoreIf you just take a heat gun to it leave it there and give it even heat distribution it'll fix itself.
How do you stop a push fit joint from leaking?
3:088:14How to Fix Leaking Quick-Connect Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make a little mark right at about 3/4 of an inch on the tubing itself. And then when you put itMoreAnd make a little mark right at about 3/4 of an inch on the tubing itself. And then when you put it into the fitting. The tubing should go in far enough that that line disappears under the collet.
How long do PEX fittings last?
Generally, PEX pipes last for 25 to 40 years before they need to be replaced. By comparison, copper pipes last for around 50 to 70 years. PVC pipes also last 50 to 80 years. CPVC pipes last 50 to 75 years.
Step 1
Cut the damaged section of PEX pipe on a 90-degree angle and remove it, using a PEX cutter.
Step 2
Slide a crimp ring over the end of each side of the removed damaged area. Slide the ring onto the pipe so it is at least 2 inches from the end.
Step 3
Press a straight insert fitting into each side of the damaged area that was removed until the fitting is pushed into the pipe as far as it will go.
Step 4
Slide the crimp ring over the end of the pipe and fitting until it is aligned over both the PEX tubing and fitting.
Step 5
Crimp the band with a PEX crimper and secure the PEX tubing over the fitting.
Step 6
Measure the distance between the fittings with a tape measure, starting from the end of the seat on each straight insert fitting.
Step 9
Press the tubing onto the open end of each side of the area being replaced until the tubing is as far as it can be pushed onto the fitting.
So back to your question of how to repair a leaking water line
The easiest way to repair a leaking water line is to cut out the damaged part of the PEX line and use a stab-in connection or crimp type band clamp. If the PEX has a simple cut or hole, you can just cut the bad area out and slip the ends into the stab-in connection.
Some plumbing experts recommend the crimp band
Some “old school” plumbing experts are not convinced the compression fittings will hold and recommend the crimp band, which requires a special tool.
HAVE A QUESTION FOR DAVE?
Ask it here. Please be as brief as possible. Attach a photo or two if it might help Dave with his response.
