Replace the Impeller - Using the Vice grip method mentioned previously, hold the motor
Electric motor
An electric motor is an electrical machine that converts electrical energy into mechanical energy. The reverse of this would be the conversion of mechanical energy into electrical energy and is done by an electric generator.
Full Answer
How to repair the leaking pump in your pool?
Suction Side Leaks
- Pump Lid. The first thing you’ll want to check is the lid on the pump itself. ...
- Cracked Pipes & Valves. Once you’ve checked the pump lid, your next stop should be the pipes and valves. ...
- Low Water Level. You want to be sure not to overlook your pool’s water level. ...
- Strainer Basket Drain Plug. Finally, locate your strainer basket drain plug. ...
How to replace an impeller in a pump?
- Turn off all of the water to your home by turning the shut-off valves to the right until they will no longer turn.
- Lay down a couple of towels under the pump and keep a few more on hand to prevent water leakage from damaging your flooring.
- Use a wrench to remove the 4 bolts on the outside of the water pump.
What is an impeller on a pool pump?
Why Is My Pool Pump Leaking
- When the Seal Breaks, the Pool Pump is Leaking. Every pool pump has a seal around the mechanical shaft that keeps water from leaking behind the impeller.
- Pump Housing. The pump housing can also leak water where it connects to the seal plate at the wet end of the pump.
- Pump Drain Plugs
- Outlet Fitting Leaks. ...
- Inlet Fitting. ...
- Pump Lid. ...
How to clean an Intex pool filter pump?
Use the garden hose with a spray nozzle to spray the filter and remove the debris. If the filter is not catching the debris or looks worn, replace the filter with a new one. Place the clean or new filter back in the pump housing. Place the cover seal on the housing.
How do I know if my pool impeller is bad?
What are the symptoms of a clogged impeller? If your pool pump impeller is clogged, it's probably making some unpleasant noises (a low, grinding sound). If you look at your filter pressure, it's likely only half of what it normally reads and the water in your pump is moving slowly or making a swirling motion.
Can you change an impeller in a pool pump?
Pool pumps aren't cheap, so when yours stops running properly, you should understand how it works and determine whether you can fix the problem yourself to save yourself some money on the repair. That's the case with the impeller. If it breaks, you can replace it on your own. You just need to know how to do it.
How do you unclog a pool pump impeller?
1:022:19How To: Clean Out A Pool Pump Impeller - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll need to unscrew the pump lid and remove the strainer basket. Next using a pair of pliers.MoreYou'll need to unscrew the pump lid and remove the strainer basket. Next using a pair of pliers. Make a small 1/2 inch to 3/4 inch hook at the end of a metal coat hanger.
How do you take apart a pool impeller?
0:074:23Inyopools.com - How to replace a pool pump impeller - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe impeller that we'll be removing is the black piece in this clip. Unscrew the four bolts that areMoreThe impeller that we'll be removing is the black piece in this clip. Unscrew the four bolts that are holding the motor housing to the pump remove the bolts and take the motor away from the pump.
Why is my impeller not spinning?
If the impeller is not spinning at all, make sure the unit is turned off and try manually spinning it with a tool, such as a screwdriver or a pen. If you are unable to manually spin the impeller, the part will need to be replaced. A pump impeller may cease to spin after not being in use for a period of time.
How do you replace an impeller?
5:3511:13How to replace an outboard impeller in 15 minutes, water pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide that down gently over the driveshaft. Line up full indents on the impeller with the key pushMoreSlide that down gently over the driveshaft. Line up full indents on the impeller with the key push right down on top. And then we'll go ahead and get our Impala or water pump housing.
How long does a pool pump impeller last?
Most pool pumps need to be replaced after 8 to 12 years of regular use.
Why is my pool pump not pulling water?
It could be something blocking it, a dirty pool filter, or too much air in the system. If there's something blocking your pump's suction, check your filter gauge. If it's 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump's flow.
Why is my pool not circulating water?
Low pressure means there is a clog somewhere. High pressure indicates it needs to be backwashed or the filter cleaned. If you have low pressure, it is possible something got through the baskets or pump pot and clogged the impeller. This is common.
How do you use an impeller puller?
2:373:52Jabsco - Using an Impeller Puller - PN 50070-0200 et al. - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's pretty straightforward make sure your crank down on the two wing nuts on either side. So thatMoreIt's pretty straightforward make sure your crank down on the two wing nuts on either side. So that these little tides rip into the rubber.
Why is my pool pump humming and not working?
If your pump doesn't turn on and instead makes a humming sound, it could be a problem with your capacitor or a jammed motor. But if it makes a humming sound that continues until your circuit breaker trips, you can be fairly certain it's a flawed capacitor.
Where is the impeller on a pool pump?
A pump impeller sits behind the pump basket in the part of the pool pump called the Volute (aka Impeller Housing). The pump basket is in place to prevent small debris from entering the volute, and possibly clogging the impeller.
How do you remove the impeller from a Pentair pool pump?
0:404:13Pentair WhisperFlo Impeller Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing you need is a little allen key okay that's going to be the little set screw here onMoreThe first thing you need is a little allen key okay that's going to be the little set screw here on the diffuser.
Why is my pool pump humming and not working?
If your pump doesn't turn on and instead makes a humming sound, it could be a problem with your capacitor or a jammed motor. But if it makes a humming sound that continues until your circuit breaker trips, you can be fairly certain it's a flawed capacitor.
How can we remove impeller from centrifugal pump?
0:212:08SMP Centrifugal Pump Open Impeller Wrench - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can now remove the impeller wrench using the knurled section of the socket. You can loosen theMoreYou can now remove the impeller wrench using the knurled section of the socket. You can loosen the impeller safely until you can remove it from the pump shaft.
How to remove impeller from pump?
The first step in preparing to remove your pump's impeller is to turn off all power to the motor. For maximum safety turn off the power at the circuit breaker to the motor - usually located next to the timer box.
Can you put a shaft seal upside down?
It is possible to place this seal upside down. Note: You may have to also have to remove the metal collar if the new shaft seal also has one. Several people have written in saying that the new seal won't fit because they were trying to place the new collar on top of the old one.
How to tell if pump impeller is clogged?
How to Tell if Your Pump Impeller is Clogged. The pump is making cavitation noises – loud, low grinding noise. The filter pressure is about half of what it normally reads. The pump basket doesn’t fill up with water (as seen through a clear lid). The water in pump is slowly moving, or swirling.
How to separate a volute pump?
Separate the volute, by removing the clamp band or 6-8 bolts that hold the seal plate to the volute. Don’t mistakenly remove the 4 motor bolts. Pull the motor straight back (it may be HOT), to separate the pump, and stand the motor on end, to look into the impeller.
What is an open vane impeller?
Most impellers nowadays are known as ‘closed vane’ impellers, which has a cover on the front of the impeller, to create the suction and draw the water in and out of the pump. Open vane impellers, also called vortex impellers, clog very rarely – but these types of impellers are only seen on old brass pool pumps, or large trash pumps.
Why do you put a pump basket in a volute?
The pump basket is in place to prevent small debris from entering the volute, and possibly clogging the impeller . Even with the pump basket in place, very small debris can pass through the pump basket, and clog the impeller. Nearly anything can clog a pump impeller, if it is the right size.
What is trapped in a pump basket?
Larger debris is trapped in the pump basket. Only debris of the right size – too small for the pump basket, but too big for the pump impeller, will clog your impeller, such as: Pine Needles. Flowering Tree Stamens. Small seeds.
What to do if your pump looks damaged?
If it looks damaged, it may need to be replaced. Once you have checked these, you should also check the pump impeller for any clogging. Once all of these things have been taken care of, you'll probably then need to prime the pump to get it going again. 3.
Why is my pool pump not pumping?
The pump runs, but isn't pumping. In this situation, something has interrupted the suction or the water flow that causes the system to work properly. In other words, it has lost its prime. This could mean an obstruction, dirty pool filter or too much air getting into the plumbing system.
Why isn't my pump basket filling up?
The pump basket isn't filling with water. If your pump basket isn’t filling up with water, the problem is probably that the pump is sucking air somewhere just like we talked about in #5. But it could also be a dirty or clogged filter or pump basket.
How to tell if a pump is leaking?
If there is a leak under the shaving cream, you'll start to see one area of foam start to pit as it gets sucked in.
How to fix low pool level?
If your swimming pool level is low, the problem can usually be fixed by filling it up. You'll also need to check your skimmer basket. If it has debris in it, clean it out well and hose it off. You may also need to fill your strainer basket with water and reseal it.
Why does my pump make a noise?
The pump is making a lot of noise. If your motor sounds a little off, it could be a problem. You’ve probably gotten used to its regular grumblings, so you know when the sounds are different than normal. If it sounds a little like one of those old vibrating beds in a cheap hotel, the problem could be cavitation.
How long should a pool pump last?
But don’t hesitate to call a professional if you need help or even just some advice. Your pool pump should give you a good 8 to 10 years of service, so if it’s nearing that age and you're starting to have serious issues, it’s probably time to start looking for a new one.